Question about 2004 Hyundai Santa Fe

Open Question

How to change a throttle position sensor on a 2004 santa fe

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: location of crank position sensor 2003 santa fe 4

hi the sensor is in with the timing belt. You will have to remove the timing belt cover and belt to put a new one in. You will also see a small gold metal rotor that spins on this sensor also replace that or it will trash the new sensor.

Posted on Mar 27, 2009

  • 6 Answers

SOURCE: how to change spark plugs on hyundai 2004 2.4L

Remove the plastic cover that goes over the engine (the one with the Hyundai logo).
At this point, you will see the cables that goe to each fo the spark plugs.
Noting their position, remove them.
The spark plugs are ready to be removed, turn counterclockwise and replace with manufacturer recomended ones.

Posted on May 16, 2009

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

c17hydro
  • 2984 Answers

SOURCE: 2004 Hyundai Santa Fe 3.5L V6 What all do I

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the retaining bolts.
  4. Remove the sensor from its mounting.
To install:
  1. Installation is the reverse of the removal procedure.
  2. Clearance between the sensor and the sensor wheel should be 0.020–0.059 inch.
Crankshaft Position Sensor The crankshaft position sensor is located at the front of the engine near the timing belt.

30c0fde.jpg

Posted on Oct 31, 2009

tracer_steve
  • 59 Answers

SOURCE: 2004 Hyundai Santa Fe 2.7 all wheel. Crank sensor

Hi

On the 2.7 engine it is located beside the starter. You will have to remove the starters heat shield to gain excess to the crank sensor.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate throttle body sensor on hyundai santa fe 2004 2.4L and replacing it


Well, we both know it is on the throttle body. follow the air filter box to the engine. Where it connects is the throttle body. Do you have drive by wire or cable? f you have cable the sensor is across from where the cables connect. If you have drive by wire, You have to replace the entire throttle body. It is a computer in it self.

Oct 07, 2016 | 2004 Hyundai Santa Fe

1 Answer

No spark, 2004 hyundai 3.5L santa fe


a cam sensor symptom is car running rough if no spark sounds like crankshaft sensor

Apr 19, 2014 | 2004 Hyundai Santa Fe

1 Answer

2002 Hyundai Santa Fe V-6 pedal position sensor location


ACEELERATOR PEDAL POSITION SENSOR IS USUALLY BUILT INTO ACCELERATOR PEDAL ASSEMBLY .........LOOK FOR WIRES COMING OUT OF ACCELERSTOR PEDAL ASSEMBLY ON THE INSIDE OF CAR NEAR OR UNDER ACC PEDAL ASSEMBLY

Jan 12, 2014 | 2002 Hyundai Santa Fe

1 Answer

2004 hyundai santa fe parked it last night, went to use it today and it doesn't accelerate, engine runs fine, no warning lights on dashboard lit, can put it in gear and move it, but absolutely no...


The 04 Santa Fe came with three different engines. 4 cylinder (2.4 lit), and two different V6's (2.7 lit & 3.5 lit). The 2.4 & 2.7 use throttle cables connected directly to the throttle plate, but the 3.5 uses ETS (Electronic Throttle System) which uses two sensors (APS & TPS) and a control module (ETSCM). APS=Accelerator Position Sensor, TPS=Throttle Position Sensor, ETSCM= Electronic Throttle System Control Module. There are different diagnostic procedures for each system.
Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, campaigns, illustrations and procedures, etc.

Sep 10, 2011 | 2004 Hyundai Santa Fe

2 Answers

I have a 2004 Hyundai Santa Fe that is idling high. If you pull up on the gas pedal it idles normal...is this the crank position sensor I am having problems with?


Crank Position Sensor ? I guess you don't know what that is !

You already answered your own question,when you pulled
on the gas pedal

Jul 24, 2011 | 2004 Hyundai Santa Fe

1 Answer

My Santa Fe loses exceleration and when diagnosed got code p2135. I was told there was a recall by hyundai for this. Is this right


Thanks for the inquiry.
P2135:
Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation
P2106:
Throttle Actuator Control System - Forced Limited Power
I would replace the throttle pedal position sensor

Best regards,
TF


Jun 03, 2011 | 2007 Hyundai Santa Fe Limited

1 Answer

Where is the throttle/pedal position sensor/switch located on a Hyundai Santa Fe (2004) and is this a repair I can do myself if I purchase the part?


Yes you can do it yourself. Here is an image showing the location of sensors on your vehicle (TPS) Throttle Position Sensor...located on the throttle body. Should have 2 screws holding it in place. You can view it in Opera and blow the image up or print the image out and blow it up on a copier if you need to. Hope it helps
If this helps you resolve your problem, please
consider giving me a good rating and a quick
thanks or good job.It will help me as well.
Thank you.

Oct 27, 2010 | 2004 Hyundai Santa Fe

1 Answer

OBD2 reader,reads P2125 ... on a Hyndai santa fe 2004 ....then it gives me this reading,Accelerator Position Circuit - Malfunction... what can i do to resolve this...


Sounds like a throttle position sensor. That is what it is called on american made cars but would serve the same function. The throttle position sensor would do exactly that, tell the engine where your foot is on the throttle ( or gas pedal) it is generally not an expensive fix, check with your parts store.

Dec 12, 2009 | 2004 Hyundai Santa Fe

1 Answer

I have a 2004 hyundia santa fe it has a very


It sounds like you have a faulty tps (throttel position sensor). If the car has a check engine light on, any auto parts store can check them for free. You should also take a good look at the vacuum lines, intake tube, and the air filter. Any vacuum leaks can cause erratic behavior. You may also want to buy a can of mass air cleaner to spray down the mass air sensor and tps as well as any other sensors on the intake. I hope this information is helpful.

Aug 30, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...