Question about Mitsubishi Eclipse Spyder

Open Question

3g eclipse camshaft sensor - Eclipse Spyder Mitsubishi Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cansmo
  • 2431 Answers

SOURCE: How is the right way to install a camshaft sensor in a 1998 4 cyl eclipse non turbo ?

If the ASD (in your case MFI) is working and your getting fuel and no spark.You need to test the coil for power ,look at the coil terminal the middle is power (B+) or 12 volts. Each other side is for ignition signal for that cylinder, Just measure the middle of the 3 wire with key on if you have 12 volts you are going to need a ECM ,There is no programing needed just match it drop in and play

Posted on Mar 07, 2012

  • 1 Answer

SOURCE: I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?

Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Posted on Mar 22, 2012

danr990
  • 1 Answer

SOURCE: 2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?

would this sensor make the car not start when it is hot?

Posted on Jun 05, 2012

  • 1 Answer

SOURCE: 1995 eclipse turns over no spark

camshaft wont cause it to not start just will cause it to run like **** take the crank sencer out and take it to the auto store and have checked out

Posted on Sep 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location for camshaft position sensor on 2.4 2005 eclipse


Remove air flow duct away from engine enough to look under it.. Cam sensor is located there.. Held on by one 10 mm bolt and clip. should be red wire, green with yellow stripe and a black one if my memory serves me right.. I have same car different year same engine.. I hope this helps you. please rate my answer thank you

Feb 21, 2013 | 2005 Mitsubishi Eclipse

1 Answer

1995 eclipse turns over no spark


camshaft wont cause it to not start just will cause it to run like **** take the crank sencer out and take it to the auto store and have checked out

Jun 11, 2012 | 1995 Mitsubishi Eclipse

1 Answer

I have replaced the camshaft sensor, Crankshaft sencor, computer, crankshaft pully, and new spark plugs on my 1999 Mitsubishi Eclipse and it still won't start, what could it be?


Engine needs spark, fuel and air to run. I assume the starter is turning the engine over. Have you verified you have spark at the plugs? Have you verified you have fuel pressure? Can you hear the fuel pump when you first turn the ignition key? If, yes to those, check the timing belt settings to make sure something hasn't caused the timing to change.

Mar 22, 2012 | 1999 Mitsubishi Eclipse

2 Answers

P0340 eclipse


Hi,

You need to inspect the entire Camshaft Sensor Circuit, right back to the PCM.

Finally, you should also inspect the entire CRANKSHAFT sensor circuit and wiring, right back to the PCM....as Crankshaft circuit failure can sometimes trigger this code.

Nov 12, 2011 | 1995 Mitsubishi Eclipse

1 Answer

My 1997 Mitsubishi Eclipse wont pass emissions because trouble code P1390. I dont know what this means? Ive researched it everyway I know? My check engine light wont come on at all? Help anyone? Thanks!


This is the direct definition of this code
Mitsubishi DTC P1390 - Timing Belt Skipped 1 Tooth or More.
Probable Causes,
-Timing belt improperly installed
-Camshaft position sensor improperly installed
-Camshaft position sensor connector improperly connected
-Crankshaft position sensor connector improperly connected
-Camshaft's relative position not relearned after one of the following have been serviced: Camshaft, Camshaft sprocket, timing belt tension-er, cylinder head, head gasket, crankshaft sprocket, crankshaft cylinder block or the PCM.

Sounds like something to do with the timing belt it self. You can go to any Autozone or Checker and ask for a code reader (they will let you use it for free) and it will show this code again. You can also reset the cars computer with the code reader to see if it comes back with the same code.

Nov 03, 2010 | 1997 Mitsubishi Eclipse

1 Answer

1995 eclipse timing missing Plz Help!


you have idle air control valve and purge valve

Mar 14, 2010 | 1995 Mitsubishi Eclipse

1 Answer

2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?


would this sensor make the car not start when it is hot?

Apr 22, 2009 | 1996 Mitsubishi Eclipse

1 Answer

Were is the Camshaft sensor in the engine?


its near the crankshaft pulley. under the timing cover.

Mar 06, 2009 | 2002 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...