Question about 1998 Ford F150 Regular Cab

1 Answer

Position of cam shaft censor in the ford f150

Diagram showing position of cam shaft censor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 48 Answers

Nstructions

    • 1

      Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.

    • 2

      Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioningposition of cam shaft censor in the ford f150 - icon1.png compressor's pulley.

    • 3

      Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.

    • 4

      Pull the electrical connection off the crankshaft sensor.

    • 5

      Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.

    • 6

      Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.

    • 7

      Press the electrical connection onto the crankshaft sensor.

    • 8

      Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.

    • 9

      Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley.



Read more: How to Replace the Crankshaft Sensor in a Ford F-150 ' eHow.com http://www.ehow.com/how_6769823_replace-crankshaft-sensor-ford-f_150.html#ixzz2Ebai9Ftj

Posted on Dec 10, 2012

Testimonial: "Great guys! i followed procedure F150 is up and running. Much thanks."

  • david_porath
    david_porath Dec 18, 2012

    your very welcome ive done this many times in my shop but to explain it is hard to do so i searched google and found the right one for you

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 191 Answers

SOURCE: 2004 ford f150 4x2 4.6 drive shaft has vibration

check the U-joints by grabbing the drive shaft and try to make it move from side to side or top to bottom.It is much easier to do this if the vehicle is in the air and no weight on the axle.If it does move replace that U-joint,but if you are going to replace one then I would do both since you will have the drive shaft out any way.Also check to see if the shaft weight is still there,but I doubt it has came off its pretty rare.

Posted on Jan 01, 2010

Armytech
  • 47 Answers

SOURCE: 1997 ford ranger cam shaft position sensor

If you have the 3.0 L or 4.0 L V6 engine, the cam position sensor is located on the top rear of the engine. If you have the 2.3 L 4 cyl. engine, you will find it on the left front of the engine behind the oil pump pulley.

Posted on Sep 27, 2008

  • 56 Answers

SOURCE: ford F250 6.0 litre turbo diesel won't start.

check the fuel cut-off switch under the glove box.

Posted on Jul 21, 2009

emissionwiz
  • 75235 Answers

SOURCE: spark plug wire diagram for 91 ford f150 302

here is a diagram, if u can't see it go to the link below.
http://autorepair.about.com/library/firing_orders/bl-fo-9225.htm


e8dfe7e.gif

Posted on Mar 12, 2010

  • 5 Answers

SOURCE: 2002 ford f150 4.2l wiring diagram

The COIL PACK TOWERS are numbered : coil----3---4 pack---2---6 plug----1---5 ----------------------------------------------------------------- The engine cylinders / spark plugs are numbered : passenger side , front to rear , 1 , 2 , 3 -----drivers side , front to rear , 4 , 5 , 6 ------------------------------------------------------------------- The spark plug firing order is ( 1 -4 - 2 - 5 - 3 - 6 )

Posted on Aug 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Ford Explorer. 4.0 liter. SOHC Good fuel pressure. & good fire on plugs. Changed crankshaft sensor . Still wont crank, No fuel is getting thru the Injectors.


check for a problem cam shaft censor as well as a crank position sensor as both are required to be operational for the ECM to start the engine

Jun 25, 2016 | 1998 Ford Explorer

1 Answer

What is a cam shaft position censor on a ford windstar 96 minivan for?


So the computer can calculate valve , ignition and injector timing.

Jul 04, 2014 | 1996 Ford Windstar

1 Answer

I have a 2004 f150 that won't start but can hear the fuel pump cut on


run fault codes to determine the sensor that is faulty. Check for cam/crank position sensor. Check that the cam shaft is turning(broken timing belt/chain). Check that the immobiliser is operational.

Apr 25, 2014 | 2004 Ford F150

1 Answer

Cam shaft position censor


Usually the car won't start or it would start intermittently. sometimes run rough

Apr 08, 2014 | 1996 Ford Taurus

1 Answer

Cam shaft position censor


You can have it tested or usual symptoms stalling when hitting bakes similar to major evap leak but when there isn't any leaks. Also can generate misfires but check plugs and coil pack first usually the coil pack if high miles then plugs if not regularly maintained. CPS doesn't go to often.

Apr 08, 2014 | 1996 Ford Taurus

1 Answer

Cam shaft position censor


Has to be tested-- at a repair shop

Codes for that sensor, do not mean you replace it

Could very well be, an internal mechanical problem,
on a 17 year old vehicle,so be careful

My money goes toward someone not being able to
diagnose it correctly

Apr 08, 2014 | 1996 Ford Taurus

1 Answer

No spark changed rotor,cap,coil,crankshaft position censor still nothing please help


run fault codes to check for cam/crank position sensor. check that the cam shaft is turning(broken timing belt/chain) check immobiliser operation.

Mar 11, 2014 | 1998 Jeep Cherokee

1 Answer

Misfire on 2 and 5


Hi Paula,

You didn't mention if you changed the plug wires.

You mentioned replacing the camshaft sensor. Have you checked the Crankshaft Position Sensor? Or the Mass Air Flow Sensor (may need cleaning)? Or the Throttle Position Sensor?

Jan 11, 2014 | 2000 Jeep Cherokee

1 Answer

My ford f 150 1998 is not fireing wheres the crank shaft censor located at


you don't have crank signal to fire your plugs is that what you mean if so check for correct power going to sensor and if hall effect or magnetic generating signal sensor in order to determine the proper testing procedure

Jan 19, 2010 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Ford F150 Regular Cab Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...