Question about 1993 Buick LeSabre

1 Answer

1985 oldsmobile regency middle nut

How do i get it off with the little wrench

Posted by on

1 Answer

What nut?

Posted on Dec 10, 2012

  • Chris Dec 10, 2012

    Sorry i ment i have a 85' oldsmobile regency with a middle nut holding the hubcap i was wondering where you get the tool wrench to remove it ..

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools are needed to change an alternator on a 1985 Oldsmobile 98 regency, 6 cyl


All you need are the correct size sockets or spanners to fit nuts and bolts that hold the unit and tension arms in place, normally 13mm or 1/2" depending on wether they are metric or imperial

Jul 16, 2016 | Oldsmobile Cars & Trucks

1 Answer

Cooling fan relay switch location 1985 Oldsmobile Regency .


Check in front of battery, black box or follow fan wire to location, fans usually plug into the relay. Also, check the fuse box too.

Feb 19, 2016 | Oldsmobile Cars & Trucks

1 Answer

Where can I find routing diagram for a 1985 Oldsmobile Regency 98 3.8 v6 .


You could try your local library, they have access to most service manuals for cars, but you have to go there to get access to them. Or you could Google for any Oldsmobile owners clubs, someone there may have what you're looking for.

Feb 09, 2015 | Oldsmobile Cars & Trucks

1 Answer

Ac relay diagram location 89 oldsmobile 98 regency


no diagram ,sorry , but usually located in the fuse/relay box in the engine compartment and the cover will have list of which is which

May 05, 2014 | 1985 Oldsmobile 98

2 Answers

I have a 95 oldsmobile 98 regency elite I cant find where the knock sensor goes I have a haynes manual but where it shows it wont go


Well, for starters, your problem got posted under 1985 Oldsmobile 98 - then you said it was a 95 Oldsmobile 98 Regency Elite (HUGE difference between 85 and 95)...then it would be REALLY nice to know which engine we are talking about.

I'll just go with what you said last: 1995 Oldsmobile Regency Elite (Two engine possibilities)

If you have the 3.8L Supercharged engine (VIN CODE "1") it is on the left side of the engine near the oil filter.

If you have the non-supercharged 3.8L (VIN CODE "K") there are TWO of them. One is near the oil filter and the other one is in about the same location on the other side of the engine block.

Please also note that MOST fault codes for knock sensors are not caused by the knock sensors themselves. (they do fail, but it is very rare.) Usually there is either a wiring problem to the knock sensor, or the engine has internal problems causing a "knocking" or "ticking" noise which causes the engine computer to "think" that there is a problem with pre-detonation causing an "ignition ping". The code sets when the computer has retarded the ignition timing as far as it can and the "knock" or "ping" does not go away....usually it doesn't go away because it is not caused by ignition timing. The knock sensor is just doing its job and reporting the knock. It does not know the difference between a knock caused by ignition and a knock caused by internal engine problems.

Jun 28, 2011 | 1985 Oldsmobile 98

2 Answers

I can't get the tie rods ends off my 1990 Oldsmobile Regency


If you cant get the nuts off. You need to grind them off or use a torch, you need a tierod fork.

Feb 24, 2011 | 1990 Oldsmobile Regency

2 Answers

I can't get the tie rod ends off of my 1990 Oldsmobile Regency.


grab the tie rod end very tite with vice grips. loosen clamp on tie rod near ball joint fit wrench or more vice grips on ball joint. try to turn the tie rod it would help to soak the threads awhile with w-d 40 or heat the tie rod where it screws in the bal joint with a propane or some type torch. before removing the tie rod count the number of turns it takes to get it out so when you put it back your front end will still be aligned. i believe it would be smart to knock the tie rod end loose before anything else. remove cottre pi and nut from bottom of tie rod end. you can use a tie rod separator that looks like afuning fork or just crawl under the ****** and beat the hell out of the tie rod bolt,not always easy,use heavy hammer.dont beat the bolt if you plan to reuse the tie rod end cause you'll never get a nut back on it. most rental shops have tie rod seperators auto zone loans them usually. good luck from sunny austin fx

Feb 24, 2011 | 1990 Oldsmobile Regency

2 Answers

1990 olds 98 regency ignition key


look at the key. if it has a little black chip in the middle of the key. if so than yes it does. the dealer can help.

Mar 22, 2010 | 1990 Oldsmobile Ninety Eight

1 Answer

Putting a belt back on... issue


you have to put a wrench on the belt tensioner rotate it all the way back, this allows the room you need to install the belt

Oct 10, 2009 | 1998 Oldsmobile Regency

Not finding what you are looking for?
1993 Buick LeSabre Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...