Question about 2002 Pontiac Montana
On most GM models, you turn the key on but don't start the engine.
Depress the gas pedal to the floor quickly three times.
The light should flash a few times then go away.
Posted on Dec 09, 2012
Testimonial: "Thanks for the quick response it worked"
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
check the coolant level fiirst...if that is low it wont give you any heat.....to change the thermostat you have to follow the top radiator hose to the engine.at the send of it you will see a clamp take it loose...then you will see the thermostat housing its held in place by 2 bolts . once you remove them you have the thermostat....make sure you clean all the old gasket material off both the housing and mount.also make sure you get a new gasket.
Posted on Jan 29, 2009
Turn key to the on position and press the gas pedal to the floor 3 times.then turn key back off then start it if it blinks at you 3 to 4 times real fast its reset..
Posted on Mar 30, 2009
turn the key on to the power position but do not start the vehicle, then press the accelerator pedal to the floor three times within a ten second period.
Good luck dont forget to rate
Posted on Apr 01, 2009
With the ignition key in RUN but engine off, repeatedly push the trip reset button until OIL is displayed on the driver info center. Once OIL is displayed, push and hold the reset button for five seconds. The number will disappear and be replaced by 100% of oil life remaining. The percentage will return to 100 and oil life indicator will be reset. Repeat steps if not reset to 100.
Posted on Dec 10, 2009
OK FOLLOW YOUR TOP RAD, HOSE TO YOUR ENGINE THAT WILL BE THE THERMOSTAT HOUSING ON A 3.4 IT IS BEHIND EXHAUST CROSSOVER PIPE THE BOOK CALLS FOR YOU TO TAKE THIS OFF. ONCE YOU GET IEXHAUST OFF THERE IS TWO BOLTS ON THE HOUSING PULL THEM PAY ATTEN. TO WHICH WAY THE THERMOSTAT IS SETTING (VERY IMPORTANT) THEN PUT TOGETHER IN REVERSE. P.S I HAVE DID THIS WITH OUT PULLING EXHAUST PIPE.
Posted on Feb 12, 2010
Tips for a great answer:
Mar 25, 2013 | 2002 Pontiac Montana
Feb 03, 2013 | 2004 Pontiac Montana
Aug 09, 2011 | 2002 Pontiac Montana
Apr 09, 2011 | Pontiac Montana Cars & Trucks
Mar 26, 2011 | 2000 Pontiac Montana
Mar 26, 2011 | 2002 Pontiac Montana
How to Reset the CHANGE ENGINE OIL Message
1. With the ignition key in RUN but the engine off,
fully push and release the accelerator pedal slowly
three times within five seconds.
2. Turn the key to OFF.
If the CHANGE ENGINE OIL message comes
back on, the engine oil life monitor has not reset.
Repeat the procedure.
You can also download a PDF version of your owner's manual for free.
2000 Pontiac Montana Owner's Manual
Feb 19, 2011 | 2000 Pontiac Montana
Oct 11, 2010 | 2002 Pontiac Montana
Dec 10, 2009 | 2005 Pontiac Montana SV6
Mar 30, 2009 | 2005 Pontiac Montana SV6
229 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: