Question about 2008 Mitsubishi Lancer

2 Answers

How do i remove rear bench seat from 08 lancer es

I need information about how I go about disconnecting the rear bench seat from my 08 lancer es. help?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

You pull up firmly on the front of the bottom side of the back seat it will pop up, one clip on each side between where your legs would go.

Posted on Dec 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 6,674 Answers

Not 100% sure on that particular model but usually you either have a couple of bolts at front of seat down close to floor to remove, one on each side, and if no bolts, you grab front of rear seat, push back on it hard & lift, usually a catch on each side.

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Mitsubishi lancer radio from loud squealing noise


What is causing that irritating noise? ' DSMtuners

www.dsmtuners.com > ... > Articles: Miscellaneous
Jun 1, 2009 - 2 posts - ‎1 author Check the ECU power relay in the console, under the radio. ... You hear a loud clicking type noise from under the hood when you try to start the car. .... You hear a squealing, grinding, or rubbing noise in the lower timing belt .... The Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, Mitsubishi Galant VR-4, ... LOUD squeak when turning steering wheel (Video Inside)
22 posts
Mar 5, 2011
Why does my alternator belt squeal so much on initial ...
25 posts
May 14, 2010
More results from www.dsmtuners.com

Lancer Troubleshooting [Archive] - evolutionm.net

www.evolutionm.net/forums/mitsubishi-evolution-forums/f-203.html
NEED RADIO HELP! ... Help not start Lancer GT 2012 EngineOverheating STOP SAFELY warning on ... AC ISSUES 2011 Mitsubishi Lancer ES · 2008 Lancer GTS no start please ... 2011 lancer no sound · Driver/Passenger side floor squeaky? ... plastic piece of rear shelf rattles a lot · Very loud noise on Lancer ES 2008 ...

Dec 03, 2015 | 2008 Mitsubishi Lancer GTS CVT Sedan

1 Answer

How do i tke the fuel pump off of a 2003 lancer es


Remove the LOWER seat in the rear, u will see ur fuel tank and the fuel float connector!
First disconnect the ( - ) pole of battery to, remove the screws holding the fuel float/pump, remove the rubber seals, and u can pull out the pump assembly!

Nov 23, 2010 | 2003 Mitsubishi Lancer

2 Answers

2003 mitsubishi lancer es fuel filter removal/replacement procedures


it's in the fuel tank, you really don't have to replace it unless you have problem with fuel pump.

b340f83.gif
to acess the fuel pump you need to take the rear seat off

bb527be.gif

Mar 28, 2010 | 2003 Mitsubishi Lancer

2 Answers

I want to convert my 2008 Toyota Sienna XLE AWD from 7 passenger to 8 passenger. How do I do it?


I don't think you can. I owned a 07 EL 8 passenger, now i own a 08 EL 7 passenger and the floor hooks for the seats are located differently (the 8 passenger has an extra hook, if I remember correctly), so i don't think its possible, look at your manual and only shows how to move the seats.

Feb 26, 2010 | 2008 Toyota Sienna

1 Answer

Cant get the rear bench in


The front bottom connections goes in first. You have to lift the back of the bench up and slide the u-shaped connections under the rods. Once there in, then lower the back of the bench. The back has latches that should spring open and around the rods in the floor opening. You should be able to actually drop the back of the bench and they should "seat", however it is better to place the back of the bench on top of the rods, and using the lever located on the bottom of the bench - open the latches; causing the latches to grab the rod.
Let me know if this helped, or if you have any additional information, problems, or questions. Feel free to contact me at FixYa.com!

Jan 25, 2010 | 2005 Dodge Grand Caravan

1 Answer

How to remove rear seat in 1996 dodge ram 1500


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

Aug 31, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

2 Answers

Putting the back seat down in a 97 Mazda Protege


The release on an LX or ES model is at the top of the seat backs, near the door opening, for the rear seats. The rear bench is a 60/40 split on these models. The rear seat does not lay down on the DX models.

Nov 26, 2008 | 1997 Mazda Protege

Not finding what you are looking for?
2008 Mitsubishi Lancer Logo

424 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...