Question about Cars & Trucks

1 Answer

I have a 95 F250 121000m original flywheel broke with a perfect circle around inner bolt pattern, replace flywheel same think happened, Help?

Flywheel will brake driving along the road with no banging or sound. The perfect circle looks like it was cut with a tool,

Posted by on

Ad

1 Answer

The torque converter ballooned & put pressure
on it

That will also cause the rear main crank brg to fail
also

Posted on Dec 10, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 625 Answers

SOURCE: flywheel

if your car is automatic and flywheel breaks then car won't go no where it will not move any more and you will hear a big knoking noise
and the cost will be between 5 to 9 hrs labor for 65 to 100 per hr plus parts depending whats the labor rate for your auto repair

Posted on May 31, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

honeymokey
  • 3113 Answers

SOURCE: 1999 RODEO PROBLEM WITH FLYWHEEL

Replace the dial pins in the back of the engine block. This aligns the transmission to the engine. It has fixed a lot of them. Sometimes they will come out when the two are separated and the mechanics put them back together without them. This will result in a cracked flywheel.

Posted on Apr 22, 2009

pippall
  • 1486 Answers

SOURCE: flywheel possibly cracked. sounds like a rod knock

you have to remove the starter to access the bolts

Posted on Jun 04, 2009

wilsodfarm
  • 986 Answers

SOURCE: 04 4.6 mustang, what are the torque specs for the

Flywheel/Driveplate Bolts 59-64 ft. lbs.I hope this helps you,and merry x mas,And please dont forget to vote on this

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is bolt torque sequence for a 2005 ford 500 3.0


Tighten them in a criss-cross pattern. First all finger tight, then each one a little at a time, in a criss-cross pattern, first one, then the one opposite, and keep moving around the flywheel like that. By the second round of tightening, you should be at the proper torque value.

Sep 12, 2014 | Cars & Trucks

1 Answer

Clutch&tranny help


you need first wipe clean fly wheel and pressure plate machined surface clean then you need to install position clutch disc and pressure plate with clutch held in place with alignment tool. tighten pressure plate to flywheel bolts only finger tight.working around pressure plate.center the clutch disc by ensuring the alignment tool is through the splined hub and into the recess in the crankshaft.wiggle tool up down or side to side as needed to bottom tool.tighten the pressure plate to flywheel bolts a little at a time working in a crisscross pattern to prevent distortion of the cover.after all bolts snug tight tighten then torque bolts 30 ft lbs for V8 if engine V6 torque bolts 15 ft lbs.be sure to use high temperature grease on release bearing inner groove place grease on transaxle input shaft bearing retainer.

Jun 16, 2013 | Cars & Trucks

1 Answer

89 toyota pickup torque specs. for flywheel and clutch bolts 22re 4x4


Thoroughly clean the flywheel bolts. Coat the first 3 or 4 threads of each bolt with sealant. Install the flywheel, aligning the previously made marks. Install the bolts finger-tight.
Tighten the bolts in a crisscross pattern and in several passes to the correct tightness:
  • 22R/22R-E manual trans-80 ft. lbs. (108 Nm)
  • 14-20 ft-lb for the clutch cover and
  • 50 ft-lb for the transmission mounting bolts.
Since you have the flywheel off, be sure and inspect the rear main seal. Now might be a good time to replace it. Be sure the rear flange of the flywheel is clean before re-install.
Be sure to inspect or, better yet, replace the bronze pilot bushing. I f you don't know how to get it out leave a comment. J


Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is really appreciated for the FREE answering of your question.

Feb 14, 2011 | 1989 Toyota Pickup SR5

1 Answer

Need a copy of the manual pages, showing how to replace the clutch


Removal & Installation To Remove:
  1. Remove the transmission.
  2. Install a flywheel locking tool.
  3. Remove the pressure plate mounting bolts from the flywheel.
  4. Remove the pressure plate and clutch disc.
To Install:
  1. Insert a clutch disc alignment tool through the disc splines and into the flywheel pilot bearing. Pressure plate balance mark location subaru-07-00-6722.gif

  2. Install the pressure plate on the flywheel with a gap of 120° or more between the "0" balance marks on the flywheel and pressure plate. Hand tighten the pressure plate mounting bolts.
  3. Tighten the pressure plate mounting bolts using a crisscross pattern 12 ft-lb (16 Nm).
  4. Remove the clutch disc alignment tool.
  5. Install the transmission.
prev.gif next.gif

Dec 28, 2010 | 1998 Subaru Legacy

1 Answer

Wanting to replace the clutch because it is slipping.


Hope this helps. Best of luck to you!
Greg

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the transaxle.
  4. Gradually loosen the clutch pressure plate bolts, in a crisscross pattern. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc.
  5. Inspect the pilot bearing. If it is worn or damaged and does not turn easily by hand, remove it using a puller/slide hammer.
  6. Check the flywheel surface for scoring, cracks or burning and machine or replace, as necessary.
  7. Install a flywheel holder to keep the flywheel from turning. Loosen the flywheel bolts evenly and gradually in a crisscross pattern. Remove the flywheel.
  8. Inspect the clutch release bearing for wear. Replace it if it sticks or does not turn easily.
  9. Inspect the release fork for wear or damage and replace as necessary.
To install: 7923kg32.gif Structural view of the hydraulic clutch system
7923kg33.gif Exploded view of the clutch assembly
Click to Enlarge
7923kg34.gif Flywheel tightening sequence
7923kg35.gif Pressure plate tightening sequence

  1. Lubricate the release fork fingers and pivot with molybdenum grease and install in the release fork boot.
  2. Install the clutch release bearing on the release fork.
  3. Install a new pilot bearing in the flywheel, if removed.
  4. Be sure the flywheel mounting surface and the crankshaft or eccentric shaft mounting surfaces are clean. Remove any old sealant from the flywheel bolt hole threads and the flywheel bolts.
  5. Install the flywheel.
  6. Apply sealant to the flywheel bolt threads and install them hand-tight. Install the flywheel holding tool. Tighten the bolts, in a crisscross pattern, to 71–76 ft. lbs. (96–103 Nm).
  7. Apply a small amount of molybdenum grease to the clutch disc splines and install the clutch disc on the flywheel, spring side toward the transaxle. Install a suitable alignment tool in the pilot bearing to position the clutch disc.
  8. Install the clutch pressure plate, aligning the dowel holes with the flywheel dowels.
  9. Install the pressure plate bolts and gradually tighten, in a crisscross pattern to 20 ft. lbs. (26 Nm). Remove the alignment tool.
  10. Install the transaxle.

May 20, 2009 | 2004 Kia Rio

3 Answers

Grinding starter on my 1988 Ford Bronco II


the sound you hear is the starter grinding against broken teeth on the flywheel, for that to be repaired the flywheel on the vehicle will need to be replaced.

MIKESTA

May 11, 2009 | 1985 Ford Bronco II

2 Answers

Have a 1979 cj7 cant find a flywheel with right bolt pattern the motor is a amc 360 but a flywheel from a 360 has a differnt bolt pattern than mine any help please


are you sure you have an amc 360 and not a 304 and also are you sure the flywheel came from an amc 360 and not a chevy 350? A 350 will bolt directly in place of the 360. You might also try a 350 flywheel.

May 10, 2009 | Jeep CJ7 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...