Question about Cars & Trucks

Open Question

Toyota Prado has stoplight and ABS light on

I have a Prado and the ABS and Brake light stays on

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: 2002 Mazda Protege ABS & Brake light

It is most likely caused by one of the ABS wheel speed sensors, those little cylindrical nipples on the back of your rotors with the cable attached to them. One way to confirm it is to read out the OBD2 codes for the ABS system, but there are some checks you can do. Visually check all four cables and sensors , and make sure there is no build up on the sensors. Make sure that the connector they plug into has good connections. Look at the wheel speed sensor and make sure the gap between the sensor head and the sprocket is the same on all four wheels (should be no more than a mm). Disconnect the wheel speed sensor cable and use an ohm-meter to check the resistance of all four sensors (they should all be similar, but don't remember the value exactly). There is a way to just disable the ABS by pulling out the 60A fuse, but if you do that you may have to plug in a code reader and use a grounding jumper on the ABS electical access box (don't remember which pin) to reset the ABS faults, otherwise you won't be able to drive around like that because your engine rpm at high speeds will behave erratically. Also, do not drive around without fixing this problem or bypassing ABS completely because it could get you into an accident. My ABS problem was intermittent, and the ABS would sometimes kick in on completely dry pavement as soon as I touched the break pedal, it almost caused me to rear-end a car on couple of occasions.

Posted on Jul 30, 2008

Ad
  • 3 Answers

SOURCE: abs brake problem

I found my solution on the web a few years ago. My 2002 RVS had permanent ABS lights and no ABS.

It was suggested to check the ABS electrical connections at the brake disks . There are quick connects there and I found a corroded connector on the front passenger side. My wife started the RVS and put it in gear. With the brake pedal pressed, I wiggled the connectors and the ABS light went "off and on" right away. I replaced the connector and it never happened again. It is likely 4 years ago.

Worth a try.

Posted on Jan 10, 2009

  • 1 Answer

SOURCE: brake lights stay on all of the time, ABS light on when driving

You most likely need to replace your brake switch, which is a
a $8 part. If you look up along the brake peddle you will see it depressing a switch. on the end of that switch is a electrical connector that you can press on one side to remove.
Once removed your brake lights will be disconected and your ABS
light should go off. You then need to replace the switch that it pluged in to.

Posted on Apr 12, 2009

  • 116 Answers

SOURCE: Dash board parking brake and ABS lights stay

you have an abs fault. have your abs system scanned for codes.

your base brakes will continue to function normally

Posted on Apr 13, 2009

pippall
  • 1486 Answers

SOURCE: 2007 toyota camry abs & brake lights on

Remove the abs plugs and dry out connections, and replace.Remove the battery wires before you do this.

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 toyota highlander abs and brake light stay on and it will not shift


hi there..... if you have a abs light on this means there is a problem
with the abs. and its usually a wheel sensor. but could be one of several problems. the only way to remove the light is to repair the fault
that is something that's isn't within the scope of the diy motorist.
and would require a visit to the professionals. only then will the light be
reset. and go out.

Nov 22, 2013 | 2003 Toyota Highlander

1 Answer

91 Buick park avenue abs light. This happened after my friend was driving down the freeway and his tire blew. Now it just blew the rubber off and he was able to drive t off the freeway on the belts. And...


ABS LIGHT AND MODULE TROUBLESHOOTING:



Anti lock brake system light comes up when there is issue with car brake systems. It can be low brake fluid or faulty ABS fuse or its issue with brake system or assembly. Your vehicles brake system needs inspection.


To troubleshoot these issues, I suggest you to refer the help links provided below. There are direct links with accurate solution, for these specific issues.


Click the link below and follow the procedure: ------


All types of ABS LIGHT / brake problems and repairs

http://howtobyme.blogspot.com/2011/11/abs-and-service-light-comes-on.html

-------------------


ABS light stays on but brakes work fine?

http://howtobyme.blogspot.com/2011/11/abs-light-stays-on-but-brakes-work-fine.html

----------------

VCS and ABS lights go on and off intermittently on Lexus?

http://howtobyme.blogspot.com/2011/11/vcs-and-abs-lights-go-on-and-off.html

-------------

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

-------------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------------------

Battery Light and ABS Light on Dash

http://whoisbyme.blogspot.in/2012/07/battery-light-and-abs-light-on-dash.html

-------------

Sometimes ABS light comes on while Driving?

http://howtobyme.blogspot.com/2011/12/sometimes-abs-light-comes-on-while.html

-----------

How Anti-Lock Brakes Work?

http://technoanswers.blogspot.com/2011/11/how-anti-lock-brakes-work.html

-------------

Brake System Troubleshooting?

http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html

-------------

Anti-lock brake light stays on all the time?

http://technoanswers.blogspot.com/2012/01/anti-lock-brake-light-stays-on-all-time.html

-------------------

ABS light comes on and Car makes Grinding noise?

http://repairhelpcenter.blogspot.com/2012/01/abs-light-comes-on-and-car-makes.html

---------------

ABS trouble codes for all models?

http://repairhelpcenter.blogspot.com/2011/11/abs-trouble-codes-for-all-1994-00-acura.html
------------

2008 Toyota Highlander: ABS warning light Blinking and OBD Error codes Coming?

http://technoanswers.blogspot.in/2012/05/2008-toyota-highlander-abs-warning.html

--------------

2003 Lexus ES: VSC, TRAC OFF, ABS lights ON?

http://technoanswers.blogspot.in/2012/04/2003-lexus-es-vsc-trac-off-abs-lights.html

----------------

2008 Toyota Highlander Hybrid: Warning Lights Abs, Vsc & Brake Are On?

http://technoanswers.blogspot.in/2012/04/2008-toyota-highlander-hybrid-warning.html

-------------

ABS & Brake warning lights remains steady on dash?

http://schematicsdiagram.blogspot.com/2011/12/abs-brake-warning-lights-remains-steady.html

------------

Can I drive the car without ABS fuse connected?

http://schematicsdiagram.blogspot.in/2012/02/can-i-drive-car-without-abs-fuse.html

-----------

Where is ABS/TCS module located on 2005 Cadillac Deville

http://schematicsdiagram.blogspot.com/2011/12/where-is-abstcs-module-located-on-2005.html

------------------

ABS motor keeps running?

http://schematicsdiagram.blogspot.com/2012/01/abs-motor-keeps-running.html

------------

When the car stops, abs pump turns ON?

http://howtobyme.blogspot.com/2011/12/when-car-stopsabs-pump-turns-on.html

-----------

Replacing ABS unit on Buick Century?

http://technoanswers.blogspot.in/2012/02/replacing-abs-unit-on-buick-century.html

----------------

2008 Toyota Tacoma: ABS causes Brake pedal fade?

http://technoanswers.blogspot.in/2012/04/2008-toyota-tacoma-abs-causes-brake.html

--------------

Toyota Camry: Premature ABS Actuation?

http://technoanswers.blogspot.in/2012/04/toyota-camry-premature-abs-actuation.html

-----------

How to replace ABS Modulator Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-modulator-control.html

----------------


How to replace ABS Pump Assembly on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-pump-assembly-on.html

-----------


How to remove ABS Accumulator on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-accumulator-on-acura.html

---------


How to remove ABS Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-control-unit-on-acura.html

------------

These details will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

Where is brake light switch 2005 prado


The brake light switch is attached to the underside of the brake pedal. You can twist and remove it then uncouple from its wiring harness.

Feb 03, 2013 | 2005 Toyota LandCruiser Prado

1 Answer

My back lights won't turn off on my toyota tercel


  • Push the driver's seat as far back as possible, allowing you to lay on the floor on the driver's side.
  • 2 Shine a flashlight at the top of the brake pedal stalk and find the stoplight switch. It will be a plastic cube either connected to the brake stalk or directly opposite the brake stalk, depending on the vehicle.
  • 3 Depress the brake pedal and feel where the brake light switch contacts the stopping plate, a metal plate in direct line with the stoplight switch.
  • 4 Feel for an open hole where the stoplight's plunger-style button presses. If a hole is present, you simply need to replace the rubber stopper.
  • 5 Press and release the plunger-style button on the brake light switch and ask an assistant if the brake lights are turning off and on. If not, the switch is bad and must be replaced.
Stoplight Switch Stopper Replacement
  • 1 Clean out any remaining debris left behind by the old stopper from the hole that the stopper goes into.
  • 2 Press the new stopper into the hole on the metal plate until it snaps into place.
  • 3 Shine the flashlight on the stopper and check that it sits flush against the metal plate.
  • 4 Press and release the brake pedal and ask your assistant if the brake lights are turning off and on.
  • 5 Replace the stoplight switch if the lights continue to stay on.
Stoplight Switch Replacement
  • 1 Loosen and remove the bolts holding the stoplight switch in place. It could be between one and four bolts depending on the vehicle.
  • 2 Pull the stoplight switch from its mount. Disconnect the wiring harness from the stoplight switch by pressing or pulling the locking tab and puling the harness away from the switch.
  • 3 Plug the wiring harness into the new switch until the locking tab clicks into place.
  • 4 Place the new switch on the mount the old switch was removed from and tighten the bolts with a ratchet and socket.
  • 5 Press and release the brake pedal several times and have your assistant check for proper operation.

Oct 31, 2011 | 1993 Toyota Tercel

3 Answers

2003 toyota abs light Codes C1203, C1223


C1223 - Left Rear Wheel Speed Sensor Input Signal is 0 C1203 - The procedure for this fault is to check for an open or short in the harness and connector between the Skid control ECU and ECM.If no faults are found with the wiring, then - the MIL stays off when ignition on but engine not running (Requires ECM replacing)
- the MIL comes on when ignition on but engine not running (requires ABS & traction actuator assembly)
These parts wont be cheap so i hope its a wiring fault smile.gif
If you take it to a Toyota dealership they should be able to do this for you pretty easily.

Mar 02, 2011 | 2003 Toyota Sequoia

1 Answer

Abs has caused brake lights to fail


Check the wires going to the stoplight switch on the brake pedal. If one of them is broken (gray wire or green wire) it can cause this problem. Or it may be the stoplight switch itself. Let me know what you find.

Jun 24, 2010 | 1997 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...