Question about 2002 Mitsubishi Lancer

1 Answer

Timing belt diagram lancer 1.5 1988

Diagram to replace timing belt and tensioner

Posted by on

  • Anonymous Mar 29, 2014

    Drive belt diagram

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 362 Answers

Here's the picture of the timing marks.

timing belt diagram lancer 1.5   1988 - 0e3bbfd.png

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a tension pulley on a 2008 Mitsubishi lancer GTS


Remove drive belt. Remove bolt and belt tensioner assembly. Reverse procedure to install

Mar 23, 2012 | 2008 Mitsubishi Lancer GTS CVT Sedan

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How to install need diagram of timing belt replacement


    2003 Mitsubishi Lancer 2.0L MFI 4cyl

    zjlimited_403.jpg

    Fig. Accessory drive belt routing-1.8L, 2.0L (SOHC), and 2.4L (4G69) engines


    zjlimited_404.jpg

    Fig. Accessory drive belt routing-2.0L (DOHC) engine




    zjlimited_405.jpg



    Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines


    Hope helps (remember to rate this ansswewr).

    Jan 05, 2011 | 2003 Mitsubishi Lancer

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    Were do you set the timeing at on a timeing belt for the lacer


    Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 2003 Mitsubishi Lancer. Plus additional Instructional and Directional Diagrams.

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

    http://www.2carpros.com/car_repair_information/year/2003/make/mitsubishi/model/lancer/2003_mitsubishi_lancer_timing_belt_diagram_marks.htm

    Mar 15, 2010 | 2003 Mitsubishi Lancer

    1 Answer

    Change timing belt galant 04 mivec 2.4


    49885ff.gif
    Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


    1. Disconnect the negative battery cable. Remove the engine under cover.
    2. Remove the crankshaft damper pulley.
    3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
    4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
    5. Remove the auto tensioner. Remove the lower timing belt cover.
    6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
    7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.

      NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.

    8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
    9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
    10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
    11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
    12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
    13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.


    284eb62.gif
    Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

    To install:


    78b2d67.gif
    Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


    b8fcecc.gif
    Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


    bad1ef9.gif
    Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

    Feb 27, 2010 | 2004 Mitsubishi Galant

    1 Answer

    How to change the Serpentine belt on a 2008 lancer?


    First, you need to have the diagram for how the belt is routed when you replace it.
    Serpentine routing diagram...


    a55b974.jpg
    Here is a link to a video on how to replace the serpentine belt. I hope it helps!

    http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229

    Nov 21, 2009 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How to loosen alternator tension on a 2003 Lancer


    I have not seen this vehicle but, the center bolt or nut that holds the tensioner to the block is backed off two turns first.
    Then the adustment bolt (most are accesed from under the vehicle) can be adjusted to give enough slack to install the new belt.
    If this is still too tight, remove one of the two or two of the three bolts that mount the Alternator to allow for another 1/8" and install the belt.
    Then remount the Alternator.
    Then readjust the tension bolt.
    Finish with the bolt or nut that mounts the tensionor to the block.
    good luck.

    Jun 27, 2009 | 2003 Mitsubishi Lancer

    2 Answers

    2003 Lancer ES High pitch squeal and constant squeak


    Shortly after replacing the serpentine belt in my lancer, the same thing happened. It is NOT the timing belt. Belts squeal when they slip. If your timing belt slipped it would cause your car to run funny.

    have somebody check the belt for wear (or do it yourself), replace if necessary. If it doesn't need replacement, just tighten it.

    If you have the 4cyl engine that I have, the tightening is kind of a pain in the ****. Not a great design by mitsubishi. There's a pulley near the front right corner of the engine in front of the alternator. the belt should be running around this pulley GROOVE SIDE OUT. This is the tension pulley.

    To tighten:
    1) Lightly loosen the bolt in the center of the pulley (slightly loosen, DO NOT REMOVE).
    2) Under that pulley there's another bolt. You can see that the bolt goes through a piece of metal
    attached to the back of the pulley. Figure out which way you need to turn the bolt to move the
    pulley toward the front of the car. (i don't remember if it's right hand thread, or left hand) This
    puts extra tension on the belt. You probably don't need much. Over tensioning the belt can
    cause pulley bearing failure. If you haven't done this work before, ask someone for
    help
    . It's better to tighten a little bit, a few times rather than overtighten once.
    3) Don't forget to ReTighten the bolt in the center of the pulley.

    If there's lots of cracks and pieces missing on the ribs or grooves of the belt you should replace it first.

    Happy repairing,
    Cliff

    Mar 07, 2009 | 2003 Mitsubishi Lancer

    1 Answer

    Timing Belt


    haines/ chilton/ mitchell repair manual. but if you are not the mechanically inclined, take it to a pro. it is possible to more harm than good.

    Sep 26, 2008 | 2002 Mitsubishi Lancer

    Not finding what you are looking for?
    2002 Mitsubishi Lancer Logo

    Related Topics:

    1,601 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    60960 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...