Question about Volkswagen Passat

1 Answer

Steam cleaned engine now have po 237 fault code

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 2,122 Answers

Hi Carl, Seems you have some condensation in the turbo boost circuit. Have it blown out with compressed air and hope that it clears the fault. The fault code refers to low signal turbo boost control. It's not a good idea to have vehicles with electronic systems steam cleaned. Regards John

Posted on Dec 09, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 141 Answers

SOURCE: Po 108 fault code

Sounds more like a mass air flow sensor problem.

Posted on Jan 09, 2009

redds55
  • 2620 Answers

SOURCE: fault po 113 and po 0102

First replace the air filter then remove the mass air flow sensor and clean the small wires inside of it with a non-chlronated brake cleaner then let it dry for 10-15 minutes then re-install it and reset the computer.This should fix your problem.

Posted on Oct 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault codes PO 193 FRP -- PO 101 MAF -- PO 380 -- PO a 09dc/dc -- PO 238 TURBO/ super charger-- PO 118 ECT -- PO 283 fuel temp sensor -- U 2023 brake sensor


101,380 and 118. These together is a no start. Take it to a garage. Just a guess, but I would be looking into the wiring. You waited to long to have a problem fixed. One bad part over time will lead to many codes. The PCM is trying to adjust to make the engine run right. Throwing other sensor out of range. Out of range pops a code.

Aug 06, 2016 | Ford Cars & Trucks

1 Answer

Po 300 Po 316 Po420 Po430 2004 Ford Taurus. The car idle high or ruff when I start it in the morning but never shut off. After I got tune up it's worse it even shut off after running for a few mins


code p 0300 refers to random /multiple cylinder/s ---misfire detected ===causes spark plug/s---HT lead/s ---injector/s --ignition coil/s ---low compression---wiring
code p 0316 refers to misfire detected during start up--first 1000 revolutions ===causes --engine mechanical fault ---wiring---ignition system---fuel system--injector/s
code p 0420 refers to cat converter system, bank 1---efficiency below threshold === causes cat converter---HO2S 2
code p 430 refers to the same problem and causes as code p 0420
Here is a news flash .
engines under the control of an engine control module (ECM) do not need you to do a tune up as it tunes the engine 60 times a minute and reports to you by fault codes when it can no longer tune up the engine

Nov 04, 2015 | Ford Cars & Trucks

1 Answer

I am getting codes PO 128, PO 300 and PO 506 on my chevy Impala, 2002, LS 3.8


code P0128 ECT ( electronic coolant temperature ) engine temperature to low ( replace thermostat ).

code P0300 engine miss fire detected ( replace spark plugs and spark plug wires )

code P0506 IAC ( idle air control ) system idle to low ( clean the IAC valve if problem persists replace the IAC valve )

Apr 15, 2011 | 2002 Chevrolet Impala

1 Answer

I need to know what the fault codes PO1116 & PO1127 that was scanned on my Ford F150 300 six 4x4.


PO 1116 is a engine coolant temp sensor code, and PO 1127 is a O2 sensor code

Apr 07, 2011 | 1996 Ford F150 Regular Cab

1 Answer

I have a 95 Maxima that occasionally stalls when I come to a stop. The check engine light was on so I hooked it up to an OD2 sensor and it gave the following 7 codes: P 1320 - Distributor Signal...


Trying to clean the MAP sensor will damage it. Install a New Air filter and The Fuel filter, then replace the MAP sensor. Do not touch, or spray(compressed air or solvent) on the element when installing it. Have all of the OBD II Stored codes Deleted. Add a can of B&G 44K fuel additive to a full tank of fuel. The B&G is the best on the market, do not substitute. It is only available Through dealerships (Toyota). It will condition fuel pump and injectors. The ECU in your car is very dependable and rarely needs replacing. Always Replace cheapest parts first. Test drive the car and Then recheck The OBD II for new faults. The dimming of your lights before shut down was due to RPM of the engine dropping below 750 RPMs. Alternator will not produce voltage below 750 Rpms. 30 Amps at 14 Volts is required to run the engine.

Mar 03, 2017 | 1995 Nissan Maxima

2 Answers

Po 140 and Po 138 codes for a Nissan pathfinder 2001


Hello! Which O2 sensor did you change? P0138 and P0140 are indicating Bank #1 Sensor #2... Is this the sensor that was changed? If it was, The sensor is reacting to a different fault...A rich condition will contaminate the sensor; It then generates a fault...Actually the O2 fault is an effect not a cause...

Does the engine run OK? Hard starting, stalls or breaks-up when you give it gas. Give me a little back ground...

There is a common fault on 2001 Nissan's that you can check; Lack of a non-resistive ground to the body...

Use an ohm meter set on the X1 scale...#1 read from negative terminal of battery to body...Then from the engine to the body...Both readings should = Zero ohms...If not .......That's the fault


Guru............saailer

May 22, 2010 | 2001 Nissan Pathfinder

2 Answers

Code PO 171


http://www.automotiveforums.com/t473813.html

PO 171 is a system to lean code. This link will explain why this is and how to fix it,

Mar 02, 2010 | 1998 GMC Sonoma

1 Answer

What is error code po 304 and po316


P0304 is Cylinder 4-misfire detected-probable cause is as follows. Engine mechanical fault, wiring, ignition/fuel system, injector, ECT/MAF sensor, ECM

P0316 Misfire detected during startup-first 1000 revolutions- probable cause is as follows-Engine mechanical fault, wiring, ignition/fuel system, injector

Aug 18, 2009 | 2003 Mercury Sable

1 Answer

Po 108 fault code


Sounds more like a mass air flow sensor problem.

Jan 09, 2009 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...