Question about 2000 Mitsubishi Eclipse

1 Answer

Throttle position sensor installation - 2000 Mitsubishi Eclipse

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Should just be two star bit screws with a pigtail plugged into it. unplug the electrical connector(pigtail) remove the 2 screws and replace the new one the same way the old came out...... Make sure to disconnect the negative battery cable whenever your working on anything electrical or replacing a sensor.

Posted on Dec 14, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle positing senser on a 99ranger I changed it now the idle is way to high


The positioning of the new TPS IS OFFSET....It is possible to install it wrong by accident..I have seen this happen before..The pressure from the sensor plastic actuator has been installed and slightly twisted against the throttle lever inside which causes throttle to raise slightly....Wear safety glasses and disconnect battery..Remove sensor slowly and carefully while removing and watch the throttle lever inside to see if it moves in any direction...Carefully install it again making sure it doesn't twist the throttle lever inside where sensor mounts...The lever on the sensor should stay in its position...Carefully install sensor making sure it doesn't twist...Connect wiring and battery and start for a safety check.....It is possible to have a wrong sensor or faulty new sensor...Double check that it is the correct sensor...

Mar 01, 2015 | Cars & Trucks

1 Answer

Where is the thorttleposition sensor on 2001jeep cherokee


The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:

selectachapter.gif

Cherokee, Grand Cherokee, 1999-2005
Throttle Position Sensor

Print


Operation

The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:


Ignition timing advance Fuel injection pulse-width Idle (learned value or minimum TPS) Off-idle (0.06 volt) Wide Open Throttle (WOT) open loop (2.608 volts above learned idle voltage) Deceleration fuel lean out Fuel cutoff during cranking at WOT (2.608 volts above learned idle voltage) A/C WOT cutoff (certain automatic transmissions only)


Removal & Installation

3.7L & 4.0L

  1. Disconnect TPS electrical connector.
  2. Remove TPS mounting screws.
  3. Remove TPS.

To Install:
The TPS is mounted to the throttle body. The throttle shaft end of throttle body slides into a socket in the TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.
  1. Install TPS and retaining screws.
  2. Tighten screws to 7 Nm (60 inch lbs.) torque.
  3. Connect TPS electrical connector to TPS.
  4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.

4.7L
  1. Remove air duct and air resonator box at throttle body.
  2. Disconnect TPS electrical connector.
  3. Remove two TPS mounting bolts (screws).
  4. Remove TPS from throttle body.

To Install:
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs. The TPS will be under slight tension when rotated.
  1. Install TPS and two retaining bolts.
  2. Tighten bolts to 7 Nm (60 inch lbs.) torque.
  3. Manually operate throttle control lever by hand to check for any binding of TPS.
  4. Connect TPS electrical connector to TPS.
  5. Install air duct/air box to throttle body.

Hope this helps

Dec 31, 2011 | 2001 Jeep Grand Cherokee

1 Answer

Where is the throttle positions sensor located


The Throttle Position Sensor, or TPS is connected to the throttle shaft on the throttle body.

zjlimited_2070.jpg

Fig. 2: Disengage the Throttle Position Sensor (TPS) wiring harness connector

According with the Grand Cherokee Repair Manual, check this removal & installation procedure...
(see Figures 5 and 6)
  1. Remove the air intake tube at the throttle body.
  2. Disengage the TPS wiring connector and remove the two mounting screws.
  3. Carefully remove the TPS from the throttle body.
To install:
  1. The throttle shaft end has a tang that can be fitted into the TPS two different ways. Only one of the installed positions is correct. When correctly positioned, the TPS can be rotated a few degrees. To determine correct positioning, place the TPS onto the throttle body with the throttle shaft tang on one side of the TPS socket. Verify that the TPS can be rotated. If the TPS cannot be rotated, place the TPS on the throttle body with the throttle shaft tang on the other side.
  2. Tighten the two TPS mounting bolts to 60 inch lbs. (7 Nm) and engage the wiring connector.
  3. Manually operate the throttle and check for any binding.
  4. Install the air intake tube.
zjlimited_2071.jpg

Fig. 5: Remove the throttle position sensor retainers...

zjlimited_2072.jpg

Fig. 6: ...then, remove the throttle position sensor

Additionally, its possible that you are interesting in some section about this repair manual: Jeep Grand Cherokee 1993-1998 (ZJ Series).

Hope this helps; just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment. Thank you for using FixYa.

Jose.

Oct 20, 2011 | 1997 Jeep Grand Cherokee

2 Answers

Where is throttle positioning sensor on a suzuki forenza


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the Intake Air Temperature (IAT) sensor connector.
  3. Disconnect the breather hose from the valve cover.
  4. Remove the air intake tube.
  5. Disconnect the throttle cables by opening the throttle and moving the cable through the release slot.
  6. Disconnect the vacuum hoses from the throttle body.
  7. Disconnect the Throttle Position (TP) sensor and the idle air control valve connectors.
  8. Disconnect the coolant hoses from the throttle body.
  9. Remove the throttle body and discard the gasket.
  10. Remove the TP sensor.
  11. Remove the Idle Air Control (IAC) valve.
  12. Remove the throttle body retaining nuts.
  13. Remove the throttle body.

To install:

  1. Install the throttle body.
  2. Connect the TP sensor connector and the IAC valve connector.
  3. Connect the coolant hoses to the throttle body.
  4. Connect the vacuum hoses to the throttle body.
  5. Connect the throttle cable.
  6. Install the air intake tube.
  7. Connect the breather hose to the valve cover.
  8. Connect the IAT sensor connector.
  9. Connect the negative battery cable.
  10. Fill the cooling system
  11. shinehutt_33.gif
  12. i hope this helps tps is attatched to hrottle body on other side than throttle cable
  13. plz dont forget to vote rep[ly if you need more help

Jan 17, 2011 | 2006 Suzuki Forenza

2 Answers

Do you have a picture to show where the throttle postion sensor should go?



Throttle Position Sensor Removal & Installation The throttle position sensor is an integral part of the Throttle Body and is only serviced as a complete unit.

Oct 14, 2010 | 2003 Cadillac CTS

1 Answer

Changing throttle position sensor on a 2004


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the throttle position (TP) sensor electrical connector.
  3. Remove the screws and the TP sensor.

923d1f7.gif
Throttle position (TP) sensor electrical connector


b3a94a2.gif
TP sensor


To install:
  1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
  2. Connect the throttle position (TP) sensor electrical connector.
  3. Connect the battery ground cable.

Apr 25, 2010 | 2004 Ford Taurus

2 Answers

Throttle position switch. how much for the part? is it easy to repllace?


This sensor sends the ECU an output signal which corresponds to the opening of the throttle valve. Using this output signal, the ECU precisely controls the air/fuel ratio during acceleration, deceleration and idling. The TP sensor and the throttle switch are combined as part of an assembly. The switch signal turns ON only when the throttle is opened to the idle position or at Wide Open Throttle (WOT) acceleration.

REMOVAL & INSTALLATION
( see Figures 2, 3, 4 and 5 )


76eea07.jpg

Fig. 2: Disconnect the wire harness from the throttle position sensor-Legacy

9b5eb25.jpg

Fig. 3: Paint a matchmark on the sensor and throttle body for ease of installation and adjustment

53c335f.jpg

Fig. 4: Remove the sensor retainer screws

f9a1aec.jpg

Fig. 5: Lift off the throttle position sensor
  1. Disconnect the negative battery cable.
  2. Disconnect the throttle sensor electrical harness.
  3. Place a matchmark on the throttle position sensor and throttle body mounting surface, so that during installation, the sensor can be properly aligned.
  4. Remove the 2 screws securing the throttle sensor to the throttle body assembly.
  5. Remove the throttle sensor by pulling it in the axial direction of the throttle shaft.
  6. Remove the throttle sensor O-ring and discard.
To install:
  1. Using a new throttle O-ring, install the throttle sensor, aligning the matchmarks. Install and hand-tighten the retainer screw.
  2. Connect the throttle sensor electrical harness.
  3. Connect the negative battery cable.

Hope this help (remember rated and comment this). Good luck.

Mar 19, 2010 | 1993 Subaru Legacy

2 Answers

Where is the TPS sensor and how hard is it to fix?


it should be on the throttle body (on the top of the engine)couple screws and about 20 minutes simple fix

Nov 21, 2009 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...