Question about Dodge Ram 2500

Open Question

Location of egr valve on 1996 dodge 2500 v10 - Ram 2500 Dodge Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BCally1
  • 133 Answers

SOURCE: EGR Valve location

4.7 does not use an egr valve

Posted on Jan 06, 2009

  • 1596 Answers

SOURCE: 2005 Dodge 1500 code p0404 EGR valve.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

  • 1348 Answers

SOURCE: 2001 dodge ram 2500 v10 oil pressure drops to 0 then back up

you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1996 dodge. ram 3500 with the v10. There is s knocking noise from under left valve cover. it goes away at about 2500 rpm untill it shifts then it's right back.


If it's upper engine noise it could just be sticking hydraulic lifters if the sound isn't constant. If it's more pronounced at a cold start that is probably all it is. A couple of things to try is Lucas Oil Stabilizer in your oil. If the sound reduces more than usual then it's the lifters. You can also try doing a seafoam treatment on the engine. There are several instructional videos on youtube for that. Also check to see if there are any Dodge v10 truck forums. They could have more specific info on the lifter tick.

Nov 24, 2012 | Cars & Trucks

1 Answer

2001 dodge ram 2500 v10 oil pressure drops to 0 then back up


you need to put an oil pressure gauge on it and see what happens.what you will find is that the sender unit is no good.

May 18, 2010 | 2001 Dodge Ram 2500 Truck

2 Answers

Where is the cam sensor located on a dodge v10


It is located under the injection pump but you may have to pull the pump to get it it a tight fit.


Sep 21, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

Location of egr valve?


The EGR Valve and transducer is mounted near the throttle body. 42224993.gif

Visit http://autorepair.about.com/library/faqs/bl948e.htm


Rate this fixya.

May 27, 2009 | 1996 Dodge Grand Caravan

2 Answers

Engine maintenance required light , stays on


I have a 1995 dodge 2500 with a v10 and it runs rough at idle and the maintenance required light came on. I have tuned it up and replaced o2 sensors also profesionally cleaned the injectors and ran sea foam cleaner thru the intake and all vacum stuff besides egr valve or injectors wut can i do plus do i have to shut off the maintenance required light for the 02 sensors to work right

Jul 31, 2008 | Dodge Ram 350 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...