Question about Dodge Caravan

Open Question

How to lower head rest in 2000 dodge caravan

The head rests on the rear bench seat are raised and we can't figure how to get them down???? They seem to be in a locked position, won't come out, won't go down.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: cannot get adjustable head rest off the seat

On the plastic pieces surrounding the insertion hole on top of the seat back,there is a very very tiny hole on the side of this piece of plastic. You need to insert a rigid piece of wire or a very fine nail of some kind into this small hole and push until you feel it give, then pull up on the headrest. it should come out. You have to do this on each of the two insertion holes. It's easier with two people.

Posted on May 13, 2009

Ad
  • 3 Answers

SOURCE: HOW TO REMOVE 2000 DODGE CARAVAN REAR SEAT

There are 2 handles on the back of the seat where it attaches to the floor. If you hold the button on the handle and push it down it should release the seat from the floor. After this it just rolls out the back. Same for the middle seat if you need to remove it.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: Need to remove head rest to put on seat covers

I looked into new headrest for my 2005 Grand Cherokee with the monitors installed in them. I had mine off but couldn't remember how i did it. But I got the instuctions from the the company with the new headrest and they linked me to a video online. The company was on ebay. I remember that it was really simple

Posted on May 04, 2009

  • 753 Answers

SOURCE: How to remove the head rest from the driver's seat 05 sunfire

There should be tiny holes in the plastic covers at the base of the chrome rods attached to the headrest use a paper clip and push it in the holes as you pull on the headrest in the full up postion.

Posted on Dec 23, 2009

ourhowse
  • 2007 Answers

SOURCE: 07 Expedition second row seat head rest cover plate removal

There should either be a little button at the base of the headrest that you push, or a small hole in the rod part, with a hole in it. Push in the hole with a pen, or a small nail to release the headrest.

Posted on Dec 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks


push back firmly at front of seat at bottomlocating clip released with upward preasure

Nov 14, 2012 | 2010 Mitsubishi Galant

1 Answer

How to remove headrests on 2010 grand caravan


lift the head rest there is a tad that the head rest slide in squeeze the tad and pull up on the head rest.

Sep 19, 2012 | 2010 Dodge Grand Caravan

1 Answer

I have a 2000 Bentley and I can't remove the rear set to pull the manual trunk release


If I am not mistaken, you have to remove the head rests, remove the bottom bench, fold down the armrest and remove the bolts behind it (Note: At the bottom, the bolts for the seat are held in by a clip... You just take a flathead screwdriver and pry it forward and it will then release. Make sure you dont let the seat-belts retract; it be difficult to get it back.) Typically, it takes about 2 hours to remove the seats. You will also need a metric set of Allen and Socket Wrenches to remove the bolts.

Nov 16, 2011 | 2003 Bentley Continental GT

1 Answer

I have a 2005 Dodge Caravan and when I push the washer for the back window it sprays on the front window. The dealer said this van only has one pump(up front). Also the power driver seat works for front...


What happens when you push the washer for the front? if this van has a frt and rear washer then there should be two buttons for the washers, if this van has two then i have seen where the pumps where connected backward so the frt sprays in the rear and the rear spray to front but again this is for dual window washers, as far as the back rest you will need to do some testing, you wiil need to test the switch for the back rest and see if its a bad switch or motor, good day.

Jun 19, 2011 | 2006 Dodge Grand Caravan

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

4 Answers

I'm trying to remove the headrest on my 2003 mustang front seat.


On the part that you squeeze to raise the head rest is a little hole on the inside between the 2 bars. You need to push a paper clip or something like that in the hole to release the stop and keep pushing as you lift. Once that is done then you can pull the rest out.

Good luck

Apr 13, 2010 | 2000 Ford Mustang

1 Answer

2009 Toyota RAV4 rear seat headrests


do the rear seats have a recline functin ,slide seat forward , should be handle below the seat, try lowering seat and then slowly raise , this may give a better sitting angle

Jun 02, 2017 | 2009 Toyota RAV4

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

1 Answer

Rear Seats


you cant drop the rear seats down only remove them with tools the straps are to install a child seat etc(one's near head rests)

hope this helps

Jun 10, 2008 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...