Question about 1985 Ford F350

1 Answer

On accelleration or when pulling a trailer or loaded I seem to no power but engine starts and runs perfect.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

I would check out the fuel filter or the EGR valve

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loses power on accelleration


run fault codes and look for MAP/MAF sensor and accelerator position sensor problems

Dec 14, 2013 | 2002 Kia Sedona

1 Answer

1999 Chev K2500 Suburban (Old Body) 5.7 / auto started running rough at accelleration, under slight load (hills, trailer, starts). No codes or MIL light. Replaced plugs & wires (only owned truck for...


If you can determine the ignition system is ok, I would look at fuel pressure and the fuel filter. If the distributor was loose you may have to check base timing.

Dec 05, 2012 | Cars & Trucks

2 Answers

Engine idles rough, lopes, but at highway speeds runs good. under load like pulling trailer temp climbs almost to overheating any ideas?


have auto zone run a scan on the truck its free overheating you need a seperate cooler for you trans pulling trailer put a high load on trans this will make the trans last longer and run cooler I would put the cooler as low as possible in the very front of your radiators

Mar 03, 2011 | 1994 Ford Ranger Supercab

1 Answer

Just bought a 1995 F250 with a 7.3 power stroke turbo. Wasn't paying to much attention at first but thought the temperature was running about 190, but know i have to baby it to not let it go over 215 when...


ENGINE AND TRANSMISSION WILL OVERHEAT WHEN YOU HAULING HEAVY LOADS OR PULLING HEAVY TRAILER.CHECK TO MAKE SURE CLUTCH FAN DONT FREE WHEEL WHEN ENGINE HOT.IF SO CLUTCH BAD FREE WHEELING KEEP COOLING FAN FROM LOCKING UP TO COOL ENGINE.MAKE SURE COOLANT LEVEL AND TRANSMISSION FLUID LEVEL CORRECT.

Dec 08, 2010 | 1997 Ford F250 SuperCab

1 Answer

My 2001 GMC Yukon 5.3l 4WD SUV is having (2) transmission problems. 1.) When cold, it shifts HARD from 1st into 2nd but after the 1st time while the engine is warm, it shifts smoothly. It started doing...


Does the trany fluid smell burnt? Might want to have the trany flushed - torque converter too - and replace the filter in the trans. FYI you may know this but it is not recomended that overdrive be enabled when pulling a trailer - especially a heavily loaded one. Does your town have lots of hills - this is an added stain on the trany.

Nov 18, 2010 | 2001 GMC Yukon XL

1 Answer

Utility trailer lights


More than likely it's a problem with the wiring. Check the wiring diagram for the trailer again and make sure the wiring is correct. It does seem like a strange problem, but something similar happened to me when I wired my trailer a little loosely on the connectors. Good luck. http://arrowtrailer.com/new.htm

May 09, 2010 | 2002 Ford F150 Regular Cab

2 Answers

Rough accelleration from Idle


try changing the ignition control module in the bottom of the distributor this controls the firing of the plugs and usually when they get hot is when they start acting up. not very expensive plus you can take yours off and have it tested at a parts store.

Aug 24, 2009 | 1998 GMC Sierra

1 Answer

1997 GMC Suburban losing power hesitation


I just went through this with a ford at the shop we threw parts at this car for days. It turned out to be the PCM. You can have all the best fuel pressures plugs, and MAF input but if the computer isn't reading it properly it can't work properly. The batterybeing disconnected is resetting the PCM taking it out of limp mode thats why it runs ok for short bursts. Its probably over-heating.

Feb 01, 2009 | 1995 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...