Question about 2003 GMC Yukon Denali

Open Question

How to replace water pump on a 2004 gmc yukon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Sarethan
  • 76 Answers

SOURCE: how do i replace my water pump on a gmc yukon xl

First you will need to remove your tension belt from all your pullies. This is usually done finding a pully that provides tension to and takes away from the belt. HINT: It will be one that doesnt have abunch of mechanical part atached behind it. After removing hte belt in the center of the motor about mid ways up there is a pully that has a hose runing behind it. The other end of the hose goes to the radiator. Well where this plugs into the motor is the waterpump. you more than likely will need to remove the pully from the pump. afd88a0.jpgAbove is a picture of your pump with the pulley removed. The four bolts in the center are how you disconnect the pulley and the four on the side of the pump are how you disconnect from the motor. Make sure when you get done and all back together to look around the new pump for leaks.


Below is a picture of the pully of and on.96e2f39.gif

Posted on Oct 24, 2009

Ad
  • 65 Answers

SOURCE: replacement of water pump on 2004 gmc sierra

Remove or disconnect the following:

Air outlet duct Coolant Inlet radiator hose from the water pump Upper fan shroud Cooling fan and clutch assembly Drive belt Radiator outlet hose from the coolant pump Surge tank hose Heater hose Water pump

0996b43f802030d1.jpg

DO NOT use cooling system seal tabs (or similar compounds) unless otherwise instructed. The use of cooling system seal tabs (or similar compounds) may restrict coolant flow through the passages of the cooling system or the engine components. Restricted coolant flow may cause engine overheating and/or damage to the cooling system or the engine components/assembly.

Install or connect the following:

Water pump. Install the water pump bolts. Tighten the water pump bolts first pass to 11 ft. lbs. (15 Nm); tighten the bolts final pass to 22 ft. lbs. (30 Nm). Water pump drive belt pulley and bolts (if applicable). Tighten the pulley bolts first pass to 89 inch lbs. (10 Nm); tighten the bolts final pass to 18 ft. lbs. (25 Nm). Surge tank hose Heater hose Outlet radiator hose to the coolant pump Drive belt Cooling fan and clutch assembly Upper fan shroud Inlet radiator hose to the water pump Air inlet duct Coolant

Posted on Jan 15, 2010

MrScary66613
  • 1990 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000

No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

  • 12650 Answers

SOURCE: HOW DO I CHANGE MY WATER PUMP ON MY 99 GMC YUKON?

remove belt drain radiator remove fan shroud remove fan /pulley remove top hose on water pump and lower hose un bolt water pump remember mark bolts because lower longer need sealant due to they go into water jacket remove and clean around both water openings before setting in place hook up upper bypass hose easier to hook up before install--replace and rebolt everything

Posted on Oct 10, 2009

  • 10 Answers

SOURCE: Heated seats won't stay on in 2004 GMC Yukon Denali

See GM TSB 05-08-143-001, If you have Adjustable pedals, especially if they don't work with the memeory buttons, but function with thier own buttons. Its the Brake Pedal Position Sensor is shorted and mesing up the seat module which controls the heaters too. My 05 Suburban had the same issue

Posted on Dec 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 yukon would start then die i replaced the fuel filter and it will turn over but wont start the fuel pump is working what could be the problem


Mass air flow meter, crank position sensor, Water temp sensor all affect starting problems. Have a diagnostic test done on it to reveal any codes that come up that will pinpoint the parts causing the problem.

Oct 25, 2016 | 2004 GMC Yukon

1 Answer

2004 yukon 6.o new oil pump still low oil pressure


main and rod bearings; when they wear out enough they reduce oil pressure. replacement of a dipstick tube o-ring is also an indication of a tired motor, especially if it was leaking significantly.

Mar 15, 2013 | 2004 GMC Yukon

1 Answer

Fuel regulator location


It is inclusive in the fuel pump. There isnt a replacement only replace the fuel pump. I just took of the intake manifold assembly to look for it and it was not there. I then dropped the fuel tank and it is not there. The answer sad to say is replacing the fuel pump. Use the AC Delco Fuel pump the generic brands failed ed a few people multiple times.

Jul 19, 2012 | 2004 GMC Yukon

1 Answer

How to change oil pump in 2004 gmc Yukon


Remove the engine oil pan then remove the screen and pump. Replace with a new screen if replacing the pump. Load the oil pump full of Vaseline so it will prime upon starting

Sep 15, 2011 | 2004 GMC Yukon

1 Answer

Leaking radiator fluid from fan pulley? 2004 GMC Yukon Denali. How can i fix this?


you need to replace your water pump. The pulley you speak of is on the water pump, and when the seal goes out, it leaks in that specific spot.

Nov 26, 2009 | 2003 GMC Yukon Denali

1 Answer

HOW DO I CHANGE MY WATER PUMP ON MY 99 GMC YUKON?


remove belt drain radiator remove fan shroud remove fan /pulley remove top hose on water pump and lower hose un bolt water pump remember mark bolts because lower longer need sealant due to they go into water jacket remove and clean around both water openings before setting in place hook up upper bypass hose easier to hook up before install--replace and rebolt everything

Oct 10, 2009 | 1999 GMC Yukon

1 Answer

2004 gmc denali leaking antifreeze


WATER PUMP WILL LEAK FROM BOTTOM OF WATERPUMP WHEN GOING BAD CHECK CARPET ON PASSENGER SIDE UNDER DASH MAYBE HEATER CORE

May 18, 2009 | 2004 GMC Yukon

1 Answer

Thermostat for 2001 GMC Yukon XL


Not true,Although,it is located in the pump,You don't need to replace the pump if the thermostat is replace.See pix
338a358.jpg56f157c.jpg

Jan 08, 2009 | 2001 GMC Yukon

2 Answers

I have a 2004 gmc yukon when I try to start it it just cant kick over, the battery is fine it just cant get the final kick to start


Check the "knock sensors" under the intake manifold, notorious for water damage. Need to check the fuel pressure as well. Fuel pump could be bad. Has the "Service Engine Soon" been on at all? It's all a "**** shoot" without the proper testing equipment.

Dec 15, 2008 | 2004 GMC Yukon

Not finding what you are looking for?
2003 GMC Yukon Denali Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...