Question about Hyundai Cars & Trucks

Open Question

How do you remove headlight assembly 2012 santa fe

Bolts and nut removed still will not come out

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: remove headlight assembly

there is a nut on the left side of the light on drivers side,just the opposite on passenger side. you will need a deep socket. there are 2 10mm bolts on top of the assy. and on the back is a 10mm nut you will have to remove on order to remove the assy.

Posted on May 15, 2008

Ad
STEVIE_N_24
  • 147 Answers

SOURCE: I need to remove complete headlight assembly on a '07 escalade

moz-screenshot.jpgmoz-screenshot-1.jpgmoz-screenshot-2.jpgBolts are located on the top, left upper grille side and right lower through outer fender assy.

Posted on Mar 29, 2009

  • 9 Answers

SOURCE: 2001 Buick LeSabre. How to remove headlight

the bolts you are looking to remove are located on the top of the light housing. It only takes 2 of them to remove the housing. One is about 6 to 8 inches long, and the other one is much shorter than that. Just unscrew and remove them, and pull the housing straight out.

Posted on Aug 31, 2009

Testimonial: "Thanks a bunch!"

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

  • 102 Answers

SOURCE: I would like to replace the headlight assembly of

There is a little aluminum stick in the assembly holding it in. On the top of the headlight twist the stick and remove it. It will look like a tent stake. Remove this stick and then the head light assembly will almost fall out.

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 2012 santa fe rear rotors ?


Remove wheel
Remove calipert bolts
Remove caliper bracket
May have screwsin between studs that need to b removed...
Might need a few hits on center of rotor area to loosen any rusty areas..

Sep 01, 2014 | Cars & Trucks

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

1 Answer

How do i remove a power steering pump on my 2003 hyundai santa fe. i removed the bottom bolt but i cant figure out how to remove the top bolt.


I presume your Santa Fe sports the 3.5 liter V6 engine? If it's got the NUT, it's at the front & there's a nut stud. If it's got the BOLT, it's accessed from the opposite (anterior) side using a long, long extension. If you have a vehicle hoist/lift, you can easily see it. If you're on your back with the vehicle on jack stands, it's much more difficult to see the 14mm bolt between the exhaust flex pipe and heat shield of the exhaust manifold at the right hand side of the engine.
Say you're directly beneath the engine oil pan, move toward the transmission and look upward and forward between the 1:00 and 2:00 oclock positions of the engine (toward the power steering pump) - 14mm bolt

Feb 06, 2011 | 2003 Hyundai Santa Fe

1 Answer

Need to change my fuel filter


The fuel filter is part of the fuel pump assembly located in the tank.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Disconnect the negative battery cable.
  4. Remove the two fitting nuts while holding the filter.
  5. Remove the filter mounting bolts and the filter from the clamp.
  6. Installation is the reverse of removal. Tighten the fitting nuts to 22-29 ft. lbs. (30-40 Nm).
  7. Connect the negative battery cable.
  8. Start the engine and check for leaks.

The fuel filter is part of the fuel pump assembly located in the tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Disconnect the negative battery cable.
  4. Remove the two fitting nuts while holding the filter.
  5. Remove the filter mounting bolts and the filter from the clamp.

To install:
  1. Installation is the reverse of removal. Tighten the fitting nuts to 22-29 ft. lbs. (30-40 Nm).
  2. Connect the negative battery cable.
  3. Start the engine and check for leaks.

Jan 24, 2011 | 2005 Hyundai Santa Fe

1 Answer

Once I remove the nuts and bolts, I can't get the headlight to move


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative (-) battery terminal.
  3. Loosen the mounting bolts and nut of headlight assembly (A).
    22140_sant_g0056.gif

    Loosen the mounting bolts and nut of headlight assembly (A)-Santa Fe
    Click to Enlarge 22140_sant_g0057.gif

    Loosen the mounting bolts and nut of headlight assembly-Veracruz
    Click to Enlarge

  4. Take care that retaining clip (A) is not to be damaged-Santa Fe.
    22140_sant_g0058.gif

    Take care that retaining clip (A) is not to be damaged-Santa Fe

  5. Disconnect the headlight electrical connectors.
  6. Remove the headlight assembly.
  7. Remove the headlight bulb:
    • Remove the headlight bulb(s) with a counterclockwise turn-Santa Fe.
    • Remove the headlight bulb after removing the bulb caps (A)-Veracruz.
      22140_sant_g0060.gif

      Remove the head lamp bulb(s) with a counterclockwise turn-Santa Fe
      22140_sant_g0059.gif

      Remove the headlight bulb after removing the bulb caps (A)-Veracruz

To install:

  1. Install the headlight bulbs.
  2. Install the headlight bulb caps-Veracruz.
  3. Connect the headlight electrical connector.
  4. Install the headlight assembly.
  5. Connect the negative (-) battery terminashinehutt_36.gif

once bolts out lift up on the headlight unit hope this helps plz vote comment reply if you need more help

Jan 17, 2011 | 2007 Hyundai Santa Fe Limited

1 Answer

I need to change the low beam headlight bulb


  1. Remove headlight mounting bolts and nut
  2. Remove assembly
  3. Install headlight assembly (with new bulb)
  4. Replace/tighten headlight mounting bolts and nut
e2ac826.gif


Oct 30, 2009 | Hyundai Motor 2003 Elantra

1 Answer

How do I replace fog lights on my 2002 Hyundai Santa Fe?


Look up into the bumper and see if you can access the fog light. The bulb should just twist out of the back. If not, the assembly should either pop forward or back to come out. I've heard though, that many santa fe's require the removal of the entire front bumper fascia just to get to the bulbs in which case you'd have to remove your headlights to get to the screws holding the bumper fascia on

Sep 09, 2009 | 2002 Hyundai Santa Fe

1 Answer

How do you change fog light on 2005 santa fe


remove the headlight assembly 10 mm bolts hold it in and the fog assembly will be accessed from there

Sep 02, 2009 | 2005 Hyundai Santa Fe

1 Answer

Broken crankshaft pully, need to know how to remove to replace


Normally...three bolts for the pulley assembly, and one large center bolt, and yes...a steering wheel puller will work, but make sure the puller doesn't sit into the center hole threads, or they will be destroyed. Sometimes a nut in here will prevent that.

Jul 28, 2009 | 2003 Hyundai Santa Fe

1 Answer

Can not remove the alternator on my 2001 Santa Fe The main pivot bolt at bottom of alternator seems to be long and can't be pushed back through the hole in alternator base enough to allow the alternator to...


The mounting bracket where that long bolt goes through is slotted. By loosing the the nut on it slightly, then ply the alternator up out of the mount( nut and bolt still attached to the alternator ).

Apr 08, 2009 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...