Question about 2001 Chrysler LHS

Open Question

How to replace a broken lug nut stud on a Chrysler 2001 lhs 3.5 Liter

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

localwonder
  • 6784 Answers

SOURCE: how do you replace the headlight bulb on a 2001 chrysler lhs.

This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Posted on Jan 28, 2009

  • 2039 Answers

SOURCE: where are the spark plugs located on the 3.5 liter

you have to remove the planium air intake and remove the ignition coil and plug are under it fairly a big job if our not use to it you have to remove lots of part be carefull please rate this a fixya our post was answer good luck pierre

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: broken/stripped rear lugs on pacifica that needs to be replaced

From Experience trying to clean the threads up usually results in just stripping the stud the rest of the way. Depending on how the car is set up (i.e. rear disc or rear drum brakes) replaceing the lug studs is fairly straight forward. All you need to do is remove the tire, remove either the brake drum or disc, and determine if you have room for removal and reinsertion of a new stud. If not determine what has to be removed to give you that room. Then comes the fun part. Take about a 2-3lb. hammer and knock the old one out. Yes, they just knock out. Then to instal the new one just set it in the hub where the old one came out, place a few washers that will fit over the knurled part at the base on the stud and the new lug nut and tighten it down til the back side if flat against the hub. Then just reinstall previously removed parts and you are done.

Posted on Apr 01, 2009

  • 5471 Answers

SOURCE: how to replace lug studs on 2002 chrysler town

I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Posted on Jul 08, 2009

1fastbob
  • 301 Answers

SOURCE: oil in 1 1997 chrysler lhs spark plug tube

although I am not familiar with this particular engine my son's Mazda Miata had oil in the plug holes and it only required a new valve cover gasket to fix it.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Remove and replace lug bolts on my 2001odysey


Jason, im guessing you old ones are either broken or stripped. It will really depend on how long the bolts are.
You can take a punch and hammer, drive out the old ones. If the new ones aren't to long you can slip the new ones in from the back of the hub.
If you are able to slip them in, you can place one of the lug nuts on the stud ( backwards) and proceed to tighten the lug nut until the new bolt completely seats against the hub.
The reason you place the lug nuts backwards is so you don't damage the chamfer,tapered end of the lug nut.

Get back to me if you have any other questions, Robert

Apr 21, 2017 | 2001 Honda Odyssey

1 Answer

How to replace lug studs


You will need a special tool to press the lug studs in and out of the flange, or you can follow these directions;

First you will have to pound the broken lug stud(s) out of the wheel hub/flange, use a punch or a drift that is a little smaller in diameter than the lug stud, and be sure that you do not pound on the flange itself, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down backwards with the flat end of the lug nut towards the flat washers to take up the slack and use plenty of grease on the threads.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Let me know if you require any further assistance.

Jul 31, 2010 | 1994 Honda Civic

1 Answer

I am wanting to replace the rear wheel studs that are broken. The wheel hub flange won't come off. Is there a special puller for this, do I need to apply more force or is there another method for removal?


You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Studs for rear wheel mounting broken off. How are they repleced?


First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Broken lug nut how to replace lug nut studs


take off tire. remove old stud by hammering it out with a punch. put a socket behind axle plate so as not to break the plate. when replacing, just start stud from back by hand, then use a lug nut to pull it in tight. when tight replace tire!

Apr 14, 2010 | 1999 Oldsmobile Intrigue

2 Answers

Heated seized lug nuts on aluminum rim now studs melted to rim


remove the control arm and the upper ball joint, possibly the tie rod too. your gonna need a air chisel more than likely.

Dec 18, 2009 | 2001 Chrysler LHS

2 Answers

How to remove car roters from a 2001 chrysler lhs


take off wheels, remove caliper and pads, either slide off or remove cotter pin and big nut unscrew and then slide off

Oct 11, 2009 | 2003 GMC Sierra

2 Answers

Broken lug stud on rear of 2001 Dodge Dakota


knock it out and draw in a new one wihtt the lug nut and some spacers.

Sep 23, 2009 | 2001 Dodge Dakota

1 Answer

Broken stud on left front wheel


Remove: wheel, brake caliper & rotor. Drive out the remaining stub with a hammer and punch. Insert a new stud and pull it into place by tightening the lug nut. Before running out of threads, remove the nut, insert a stack of washers or a large nut which slips over the threads without contacting them, tighten the lug nut to seat the stud.

Jul 12, 2009 | 2001 Pontiac Sunfire

1 Answer

How to replace lug studs on 2002 chrysler town


I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Jul 08, 2009 | 2009 Chrysler Town and Country

Not finding what you are looking for?
2001 Chrysler LHS Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...