Question about 2000 Isuzu Rodeo

Open Question

Diagram of 2000 isuzu rodeo timing

Need a diagram of timing marks on camshaft

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dsacco86
  • 1077 Answers

SOURCE: I need a serpentine belt diagram for the 2000

Here you go:
c584456.jpg

Posted on Mar 27, 2009

digritz
  • 530 Answers

SOURCE: i need a serpentine belt diagram for a 2000 isuzu

Here's two belt routing diagrams.
The first is for the 2.2L engine and the second is for the 3.2L.
Hope this helps.


94741d0.jpg





75c046e.jpg

Posted on Nov 07, 2009

Testimonial: "THANK YOU!! I was going crazy. Couldnt have done it without you help. "

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

johnjohn2
  • 5763 Answers

SOURCE: need to know the timing marks for a 99 isuzu rodeo

Heres two diagrams for aligning the timing gears for timing belt, this is for a 1999 rodeo with the 3.2 engine, hope this helps,one diagram is for the cams and the other is for the crank gear,d5220b7.gif813ac66.gif

Posted on May 20, 2010

  • 82 Answers

SOURCE: isuzu rodeo 2000, LS, anti-theft alarm needs to be reset

This has to do with the Auto's Computer system and should ONLY be done by a Factory Rep who knows what he/she are doing. not a home mechanic chore!!

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know where the timing marks are on a 96 4wd isuzu rodeo. CAN ANYBODY HELP ME PLEASE?



  • I hope you get this, I was going to go to bed until I noticed how bad you were needing some timing marks :)

  • Injection pump and camshaft alignment marks-diesel engine
ironfist109_302.jpg

ironfist109_303.jpg

  • Tensioner pulley bolt sequence (diesel)


ironfist109_304.jpg


  • Crankshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_305.jpg

  • Camshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_306.jpg
  • Timing belt installation sequence-2.3L and 2.6L engines
ironfist109_307.jpg
  • Timing belt tensioner lockbolt-2.3L and 2.6L engines
ironfist109_308.jpg

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1996 Isuzu Rodeo

1 Answer

Can u send me a pic. or diagram of the timing marks on a 2000 isuzu rodeo 3.2L


yes i can give me youre email ang i wiil give you the timing marks

Mar 20, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Need to know the timing marks for a 99 isuzu rodeo with the3.2 dohc


Heres two diagrams for aligning the timing gears for timing belt, this is for a 1999 rodeo with the 3.2 engine, hope this helps,one diagram is for the cams and the other is for the crank gear,d5220b7.gif813ac66.gif

May 20, 2010 | 1999 Isuzu Rodeo

1 Answer

Replace timing belton 1995 isuzu 3.2 V6


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1995/make/isuzu/model/rodeo/1995_isuzu_rodeo_timing_belt_diagram_marks.htm

Nov 23, 2009 | 1995 Isuzu Rodeo

2 Answers

Won't start after timing belt has been replaced


The cam pulleys turn 3 or more turns to one of the camshaft. You need to find someone that is experienced on this vehicle. Just aligning marks does not mean its in sync.

May 08, 2009 | 2000 Isuzu Rodeo

2 Answers

Timing belt alignment


A factory service manual would help, but I'm assuming that if you had one, you probably wouldn't be on this site.

To set the timing, you need to first perform the obvious: remove the accessory drive belts, cam pulley covers, and engine fan and hub. Next you'll need to rotate the engine by hand until the timing marks on the camshaft sprockets and crankshaft are aligned with their corresponding stationary marks. The 0 degree mark on the lower timing belt cover is the timing mark for the crankshaft pulley. There is a mark (small, vertical formed indentation) for the left camshaft pulley on the backing plate behind the pulley near the 1 o` clock position. The same mark exists for the right camshaft pulley only it is on the backing plate near the 8 o`clock position (making it difficult to see). With the crankshaft placed at the zero mark, you can observed where the timing discrepancy exists.

(TIP: Once the right camshaft timing is properly lined up, etch an additional mark on the pulley's face and the backing plate at the 12 o`clock position. This will make it easier to align the pulley for furture adjustments and repairs)

To set the timing correctly, move the crankshaft pulley to 12 deg. BTDC. Being careful to not disturb the position of the crankshaft once it has been moved to that position, remove the crankshaft pulley, lower timing belt cover, timing belt tensioner, and timing belt. Compress the timing belt tensioner and if the original ring pin isn't available to retain the tensioner a small allen wrench can be used to achieve the same results. Line up both camshaft marks and reinstall the timing belt and timing belt tensioner (do not remove the timing belt tensioner tool used to maintain the tensioner piston in a compressed position). When installing the timing belt, be sure to allow the least amount of slack to exisit between the left camshaft pulley and the crankshaft sprocket, but without moving the pulleys.

Next, remove the timing belt tensioner piston retention tool and mount the lower timing belt cover and crankshaft pulley (without fully installing them). Rotate the crankshaft pulley to the 0 deg. mark. If done correctly, moving the crankshaft pulley from 12 deg. BTDC to 0 deg. will remove all remaining slack from the timing belt assembly and the camshaft pulleys and crankshaft pulleys will be lined up with their corresponding marks. Once proper timing has been achieved, install all removed parts.

(Another TIP: I hope it's not necessary, but in case it is, I'll remind you that proper torque of all bolts are necessary as this is an all aluminum engine. Stripping out bolts holes due to over-tightening bolts occurs very easily and become very annoying to deal with [e.g. alternator belts not being able to be tightened completely and constantly squealing every few days, etc.])

Apr 26, 2009 | 1997 Isuzu Rodeo

1 Answer

Isuzu trooper 2002 RLV engine. camshaft timing


Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Feb 21, 2009 | 2002 Isuzu Trooper

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...