Question about Cars & Trucks

1 Answer

No brake lights on 1999 gmc k3500

Changed brake stop switch at peddel and changed turn signel hazzard switch on steering colum. have running lights,both turn signels and hazzard lights at back of truck,but no stop lights.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,431 Answers

Where the brake lamp attatches to is called a tail lamp assembly,some call it a rear light module,they are sold in pair and they do fail,you did the brake switch and the combination switch,either the wire is disconnected some how or the lamp assemby both side failed,

Posted on Dec 09, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

emissionwiz
  • 75189 Answers

SOURCE: gauges go out, car runs fine, radio works, abs light on turn signal works

this is a body control module (BCM) fault, replace it..

Posted on May 30, 2009

  • 1509 Answers

SOURCE: 1996 Chev Silverado K3500 dually, no brake lights

The chevys with red brake lights and turn signals do two things and I've fixeds alot of them. Looking at the tail lights with the hazard flashers on. both sides flash with nothingeles on? Or are the hazards yellow? if they're red and the third eye does work the turn signal switch is possible problem but it doesn't let the blubs and the circuit boards in the taillights out as they can fail and do some really bad stories the wires for the brakes and the turns and the hazards are the same ones and if the turns look right and the hazards look right then the turn signal switch transmites the turn too as this doesn't work part of your story can't be true

Posted on Aug 19, 2009

  • 5 Answers

SOURCE: 1997 gmc 3500 box truck. no brake lights. changed

Check the fuse.

Posted on Sep 18, 2009

  • 12 Answers

SOURCE: 1999 GMC Suburban, K1500 4WD. Top brake light bar

third light is different circuit. saftey reason check fuses grounds wires

Posted on Oct 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

K3500 pick up has no brake lights


The brake switch may be bad or out of adjustment. also check wiring all the way from switch to box and to the lamps.

Dec 09, 2012 | GMC Cars & Trucks

1 Answer

1995 GMC Jimmy brake lights not working


Brake lights run through the hazzard switch. There are known problems with this, and the multifunction switch. You may need to buy a new hazzard switch and OR the multifunction switch. Before you do that, check the pigtail that goes into the brake switch up by the fender, make sure it's not shorting out up there. Happened to me!

May 06, 2017 | 1995 GMC Jimmy

1 Answer

Driver side turn signal not working, changed bulb and when hazzard lights on this one still does not work


some possible causes are there could be a bad light socket,loss of power for the wire that operates the signal.have you checked to see if the light works when you push on the brake pedal.if its not then you could have a bad signal switch in the steering colume.i`m guessing the front light is working as you don`t say.

Jul 05, 2011 | 2006 Ford Fusion

1 Answer

What could cause brake lights to work every now and then


I would check your brake light swich located under dash just fallow your brake pedle with a test light see if you have power going to it slitely press brake pedle see if other side of switch has power (key on car not running) if not try ajusting it by pulling on it or unscewing it if all checks out ok replace turn signal switch disconnect battery remove center part of steerring remove center bolt with steerring puller pull steering wheel with locking plate puller pull locking plate remove turn signal handle emergency button three scews holding turn signal under dash fallow steering colum disconect wires on right side (passenger side) tape a long wire to end of connector pull turn signal without pulling tape wire all the way out so you can tape it to new turn signal wire connector to be able to pull wires back down steerring colume (you might have to losen steerring colume and bracket two scews under dash four on steering colume)

Jun 27, 2011 | 1998 Dodge Ram 3500 2WD

2 Answers

1998 gmc truck 5.7 liter, I need to know the


Should be located above break peddel next to steering colume under dash.

Aug 30, 2009 | 1998 GMC Sierra

1 Answer

Blowing fuse in fuse box for brake and hazzard


its possable there is one of those lights turned in the wrong way or to much or shorting out in the socket crossing .
maybe no promises.but a good check for sure.
also check for the wrong bulb types.

hope this helps
thank you
jm

Jun 18, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

Brake lights out


have you tried replacing the bulb

May 31, 2009 | 2005 Ford Mustang

1 Answer

Blowing brake light fuses everytime you hit brakes.


Sounds like a short in the steering colume, maybe the turn signal switch, or a wire that the insulation got wore thru in the colume. Unhook break light switch and try the turn signals and hazards again and see what happens, maybe you can isolate it that way. Also if you havent done it already chk.the sockets in tailight housing for corrosion and bear wires, or anything, even ground wires.

Apr 10, 2009 | 1998 GMC Jimmy

1 Answer

My flasher work but brake light not work just roof lighting went aply brake


Chk. fuse, emergency flashers, and middle break light, and the other break lights are on seperate curcit (a fuse for each), if fuse is ok than it could be break light switch, witch is located under dash on steering colume and works off break peddel arm.

Mar 28, 2009 | 1998 Chevrolet Blazer

3 Answers

Brake lights/rear turn signals


I had the same problem with my 1999 Yukon. The electric board needed to be replaced. Rust starts to build up and shorts out or blows the bulb. The dealership charged $73.60 for the part and I installed it myself (Saved $30).

Dec 14, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...