Question about 1999 GMC Sierra

1 Answer

Rear tail light and brake light comes on but left rear turn signal is out

Left rear tail light and brake work, but left rear turn signal is out

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Replace bulb

Posted on Dec 09, 2012

  • roosevelt george Dec 09, 2012

    That was the first thing I tried. The left rear turn signal is still out.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

2 Answers

I have 89 bronco 2 my brake lights turn signals both work my tail lights don't work have check fuse n blubs what might be the problem


The turn signals and brake lights use the same circuit and filament in the bulbs. The tail lights are on the other circuit which comes from the headlight switch.
Do you have power on the tail light fuse ?

Feb 25, 2013 | 1987 Ford Bronco II

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Brake lights not working at tail lights but the light in the rear window does come on when brake pedal is pushed.....regular tail lights come on...right and left turn signals also work ....flashers...


the upper brake light works differently than the outer lights. check your brake light switch by the brake pedal.It will have a plunger switch on it. The center brake lamp works off a power convertor instead off the brake light switch. The switch has a separate wire for that which is still working

Feb 19, 2010 | Ford Contour Cars & Trucks

1 Answer

Brake light and turn signal light not working


Did the new lens come with new sockets? If not damage may have occured there that you cant see. only other possibilty is wiring damage in the rear that may be hard to see. The condition you describe is simple "backfeeding" if you look hard enough youll either find bad sockets or damaged wires close to the lens that took the hit. Hope this helped. Thanks

Apr 06, 2009 | 2004 Jeep Liberty

2 Answers

2001 Explorer Sport ,Rear Driver Brake Light and Turn Sig. Broke


Rear lights are double filament bulbs one side for the lights other side for the brake/turn signals so it still may be a bulb. Do u have a test light or volt meter you can check to make sure u have power there when brakes or turn signals are activated. Or just try another bulb.

Feb 12, 2009 | 2001 Ford Explorer Sport

1 Answer

2006 Chevy Trailblazer Tail Lights


There was a recall on this, take to the dealer and they will replace the whole socket on this.

Nov 06, 2008 | 2006 Chevrolet Trailblazer

3 Answers

Trailer wiring for 06 GMC Canyon 4x4


exactly what does it do? please explain what happens when you press the brake turn on the light than brake signals ect.....

Aug 13, 2008 | 2006 GMC Canyon

Not finding what you are looking for?
1999 GMC Sierra Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...