Question about 2003 Dodge Durango

1 Answer

Lost front drive shaft in 2003 dodge durango.....are there any seals that will need to be replaced ??? HAve not messed with it yet ..

Posted by on

1 Answer

Get under it & find out what you think is the issue

Then get back to us

I like to pull all drive shafts & whether I replace joints
or have them done,I only go to a drive shaft shop,only
with my parts & have it balanced

Posted on Dec 09, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

  • 245 Answers

SOURCE: location of speed sensor for a 2003 dodge durango

the speed sensor for this vehicle is actually in the rear differential of the vehicle. this is the sensor that runs the speedometer also known as the vehicle speed sensor. there are also two speed sensors in the front one on each wheel known as wheel speed sensors these are for the abs system only

Posted on May 17, 2009

  • 2 Answers

SOURCE: 2003 Dodge Durango clunking noise in front end can

With the information given this is not a sure solution. Questions that need to be asked is when does this happen, turning at slow speedm high speed, when hitting a pot hole etc? Since you have replaced a lot of things already, assuming you have NEW good quality parts so you did not replace bad parts with new bad parts i would definitelu check the pitman arm. This runs from the stering gear to the tierod. It can give you some good clunks while steering, especially at low speed when there is a lot of resistance. Check it by having someone turning the steering wheel when watchin/feeling it.

Posted on Sep 18, 2009

  • 1757 Answers

SOURCE: 2003 dodge durango front heater/ac blower motor

Check the Blower Motor Resistor. This controls the Blower Motor/Fan Speed.

Posted on Dec 27, 2009

wracefans24
  • 1985 Answers

SOURCE: 2003 dodge durango front heater will not blow

Since your blower is working and it is a heat issue,thats where we'll start,First thing is have you checked the coolant level in the radiator when engine is cold,make sure it is filled to top,next verify you have coolant in reserve ,Start your van and get it up to normal operation temperature,If your heat gauge on the dash works correctly it should be 190 degrees,Now lift the hood and locate the two heater hoses going into the heater assembly at the fire wall,Both hoses should be hot to hold on to,if both are hot and no heat inside your problem will be the blend air door in heater assembly.
if neither hose is that hot you need to replace the thermostat in the engine to get it up to 195 degrees.
if one hose is hot and one is luke warm then the heater core is blocked and to blame. hope this helps you.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a tranny in my 2005 Dodge Durango and I can't get the front drive shaft to go back in. There is simply not enough room. How do I get it to go back in?


Hate to tell you this but the front drive shaft has to be put in before you completely install the front drive axle. Do this lift front of ground put jack stands under body loosen up the front drive axle to the point you can get the drive axle installed. Good luck.

Jul 28, 2015 | 2005 Dodge Durango

1 Answer

Front left wheel grinds when you put my 2001 dodge Durango when you put itin 4 wheel drive..how do I fix this?


The c/v axle and output shaft on the front axle are worn where they spline together, they need to be replaced

Dec 14, 2014 | 2001 Dodge Durango

1 Answer

2002 Dodge Durango SXT 4.7L RWD shaking (serious vibration) badly between 70 to 80 mph


If it were me I would take out the drive shaft and check the play in the universal joints (I know you said they were replaced). Unlike ball joints they should exhibit good freedom of movement and flop from one position to the next as the shaft is rotated in the hand. Check that the bearing cup retaining clips are present on all sides. If there is any tightness in a bearing it is possible that either one of the cups has been pressed (hammered?) in too far or that a needle bearing was dropped from the outer race into the cup during assembly. Also check that the cup holders (arms) are not bent, sometimes if care is not taken to support the back of the 'arms' when installing the bearing cups the 'arms' will bend.

Feb 28, 2017 | 2002 Dodge Durango

3 Answers

I have a hard clicking sound coming from the front left tire of my 2003 durango. The clicking occurs when turning in reverse and accelerating going straight. When I lifted the front left wheel I could...


could have been lose lugs
or ABS sencer
or something cought in tire area back of rim or even the wheel well splash gard lose
stock tires will not have this issue but over sized ones might
just some areas to check on

Nov 28, 2010 | 2003 Dodge Durango

1 Answer

How to replace a front seal on a 200 dodge


Hello, not hard to do. You need to remove the drive shaft, to get to the nut that holds the rear yoke from the differential. Once the rear yoke has been removed, you can replace the O ring seal from the differential by using a screw driver to pry out the old seal. Try not to damage it to much so you can use it to help tap in the new seal. Once the seal is out place the new seal in place by hand and then place the old old seal on it and tap in the new seal with a small hammer. Take care to ensure that the new seal goes in straight and place some grease on the seal before you place the yoke back in to place. Tighten up the yoke nut and you may want to replace the U joint at this time too since it's off the truck. Once everything it back together, check the differential oil level and top off. Good luck and hope this helps, you can get the parts at Auto Zone and they can also give you the step by step instructions to getting the job done with common tools. The hardest part that i can see you having is the removal of the yoke nut, the job takes about an hour to do so if your going to have a garage to the job the most would be 1.5 hours but should take them about 30 min to do.

Thanks

Jul 27, 2010 | 2000 Dodge Durango

1 Answer

How do you change the front axel seal


Which seal do you mean?? The CV boot on the front hal fshafts or the seal on the outside of the differential assembly?

Either one is not too tough, but the rough part in either case is removing the half shaft assembly on the side of the leak.

Don

Apr 10, 2010 | 2003 Dodge Durango

1 Answer

2001 dodge durango 4 wheel drive not working loud knocking


You need to check the cv joints in the front end or the u joints in the front drive shaft.If none of the above then the problem is internal in the front diff.

Jan 28, 2010 | 2001 Dodge Durango

1 Answer

Popping and clicking in 2003 dodge durango steering column, it feels as if the column is loose at some point, it's not in the front end, it seems to be from the firewall up to the steering wheel


i believe there is a replacement steering shaft from dodge to get rid of this noise,the dakotas have the same problem,it comes from the shaft design and the flex of the body mounts when u accel or deccel,hope this helps

Sep 05, 2009 | 2003 Dodge Durango

1 Answer

Getting rear gears out of the difential case 1999 dodge durango


  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Feb 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2003 Dodge Durango Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...