Question about 2005 Nissan Murano

8 Answers

Sun visor on 2005 Nissan Murano won't stay up/falls down

The driver's side sun visor falls down and will not stay up. I've tried to see where to tighten screws, but find only plastic covering. Does anyone know how to fix? Or remove plastic covering to get to screws?

Posted by on

  • 16 more comments 
  • NissOwner Jan 26, 2009

    Visor falls down continuously for me as well, and has actually become a serious driving hazard. Never had a visor do this. Dealership says it's out of warrantee (past 36K miles). I couldn't get them to explain how mileage affects a sunvisor (much the same as it would affect a glove compartment or door handles). Nissan dealership "offered" to fix it for $450 (before tax). Nissan stated there were electronics involved which caused the price to be so high. The electronics are a battery operated light in the visor which probably costs all of 10 bucks. I can't find a way to adjust the visor either. If someone has come across an idea of how to fix this, I'd be much obliged. (I've tried velcro, tape, a wire contraption that looked like ****, but the visor is hell-bent on falling down no matter what you do)

  • Anonymous Jan 26, 2009

    This is a widespread problem on these vehicles and Nissan won't own up as usual. Nissan sucks...buy American.

  • ruapeper Jan 30, 2009

    Thank you, Scott99; I haven't yet tried this but sounds like a good idea. I'm with you, it beats the heck out of $350 or more.



    Think I'll send a note to Nissan--maybe if they get enough complaints, they'll finally do something about it!

  • Anonymous Feb 12, 2009

    Same problem

  • Yvonneus Feb 16, 2009

    I have Murano 07 with broken sun visor.Could you please report this problem at www.nhtsa.gov. There is a chance for recall. Thank you.

  • Anonymous Feb 18, 2009

    Same Problem...

  • lnscon3 Mar 05, 2009

    2006 Sun visor on drivers side will not stay up. Dealer quoted $431 to replace it.
    Anyone know how to fix it or where I can buy one myself so I can try to fix it.


  • annb361 Mar 06, 2009

    I have a 2004 Nissan Murano SE...The driver's side sun visor will not stay up. It is a driving hazard. Can't afford a new one at $400.00. Any idea how to fix this. This is obviously a manufacturing defect.Annb

  • Anonymous Mar 19, 2009

    I have the same problem. 2005 Murano, drivers side sun visor won't stay up. Quoted $200 - $300 to fix.

  • Anonymous Mar 23, 2009

    I have a Nissan Murrano 2006 and the driver's side visor wont saty up. I know know it is a problem with the Murrano. Iwas looking online to finr a replacement visor. I was unable to find one and the dealer wants mad cash. I do not want to put Velcro. Does anyone know where you can find a new visor?

  • Anonymous Mar 27, 2009

    I also have the same fricking problem i bought a 2004 nissan murano, and the sun visor on the passenger's same not to stay, it keeps falling.

  • Anonymous Apr 01, 2009

    Sun visor on 2005 Nissan Murano won't stay up/falls down" problem,too. I need to know how to fix the problem as well. mingda

  • bella7772 Apr 14, 2009

    My 2005 Nissan Murano Driver side visor won't stay up. Didn't realize I wasn't the only one with this problem... $350 bucks is ridiculous for a replacement. Sounds like an epidemic...

  • MadAZ Murano Apr 15, 2009

    Same deal as all the posting on here, I have a 2006 Murano and I just came from the Nissan Dealership where they offered to rape me and lead me out the door with a $400+ "VISOR" RIDICULOUS.



    Note to Nissan, make better parts or charge realistic prices for your replacement parts. Oh and I also checked on a piece of a metal frame for my driver side seat $700 for that one.



    Sorry Nissan, not in this lifetime.



    Mad 'AZ' Murano Owner.

  • Anonymous Apr 15, 2009

    Visor has drooped since day ONE on our 2003 Murona. Nissan dealer replaced a clip which did not correct it but since we had to replace 3 alternators, 1 door harness and the digital clock that did not keep time we figured we would just dump it and never buy another Nissan. Problem solved....kind of.

  • texritter Apr 29, 2009

    I have 04 Murano with the same problem,it just falls down when you hit a bump on the road.How can this be fixed?

  • Anonymous May 17, 2009

    sunvisor only stays in certain positions

  • philip Aug 07, 2013

    Inside the visor there is a cover and clamp over the arm that basically puts tension on the arm preventing it from being floppy. The plastic arm that the visor rotates on pretty much desintegrates and/or in my case there is a flat part which also gets worn and rounded. I kind of doubt a plastic bond will hold up to the repair; but I may give it a try. Not sure with what though.

×

8 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Go to a dealership with a screwdriver and your broken sun visor in hand. take out a nissan murano with an interior that matches yours for a test drive and perform a switch on the sun visors. install your broken visor in place of the one that works, and take the one that works out of the car that your test driving.

Problem solved, its free, and you didn't have to get creative to fix the problem. Plus, they can't blame you for a broken visor considering that they fail in these cars all the time. You're welcome!!!

Posted on Jun 27, 2010

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I resolved this same problem on my 2004 Murano after also being told that it ($350 Visor) was not covered under my extended warranty. This problem is primarily caused by the heavier than normal visor. It cost me a total of $2.69 and about 30 minutes to fix.
To resolve this problem follow the following steps:

1) Go to the hardware store and purchase the Velcro package that contains (2) 18”, 1/2 inch strips (I chose the beige color since I have a tan interior) 2) Using a small screw driver, carefully pry off and remove the small cover that hides the mounting screws for the Driver’s visor. 3) Remove the 2 Phillips screws and drop the visor down slightly so that you can unplug the wires that go to the visor light and now remove the visor 4) Using the plastic velcro strip ONLY , (NOT the fuzzy strip), trim the end of the strip so that it will fit under the visor mount and also punch a small hole in that end of the strip so that one of the screws will go through it. (There is NO NEED to remove the adhesive backing from the Velcro strip)
5) Carefully mount the visor so that one of the mounting screws also goes through the Velcro strip 6) Be sure that the sticky side of the Velcro strip faces down or towards the visor
7) Once the visor is loosely mounted, pull the Velcro strip slightly and then tighten the 2 mounting screws securely. 8) Once mounted, hold the Velcro strip against the headliner and then raise the visor against the strip and the headliner and it SHOULD stick in place since it can’t drop down because one end of the Velcro strip is secured to the visor mount 9) Trim the exposed end of the velcro strip so that only 1 inch is exposed (or less) in case you need to lower the visor at a later time. (I removed a half inch of the backing and folded the exposed end on itself so that it's easy to grasp.) In this way you don’t have to glue anything to the headliner OR the visor.

(If your visor is a vinyl material, you will have to stick/glue the fuzzy velcro strip to the top side and/or edge of the visor so that there will be something for the plastic strip to stick to)

I hope this helps others…. It works for me! (and it sure beats $350!!)


Scott99

Posted on Jan 30, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Removed and now replacing my broken visor on my 2006 Nissan Murano with just enough time to sell my vehicle. Shame on you Nissan for making such a crappy part and for raping the customer on a new visor. I will never ever ever ever ever buy a nissan again.... C YA!

Posted on Aug 23, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I fixed mine on a 2007 Nissan Murano but buying some strong small magnets at Lowes. Put one through the hole after taking off the visor. I stuck the other on the back of the mirror with velcro. Stays up like a charm. Magnets at Lowes were about $5.00. Beats $300 at the dealer.

Posted on Jan 05, 2014

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I have the same problem with the visor on my Nissan Murano 2003. Got some visor from the junk yard for little to nothing compare to $350 Nissan were goin to charge me. Ask for both visors (driver and passenger side) and clips....problem solved.

Posted on Aug 25, 2013

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I just cut my visor apart tonight and here is the situation. The arm/shaft for the visor has plastic molded onto it. It then runs through two steel loops with space in the middle for a tensioning clip. Regretably, you must cut off the fabric cover near the arm and through some styrofoam that makes up the shape of the visor to get to the arm and tension clip. The clip apparently wears off the plastic that is molded to the arm and when that happens it will not hold its shape. I was only half successful on my complete fix. To truly reach the arm/shaft, you first need to pry off the cap from the (towards back of car) back side then take out the two screws and at same time unplug the electric connection. Then remove mirror/lamp on one side of visor to remove shaft after you unplug the mirror/light There are two screws under the white light cover. Then you can cut the fabric cover near the arm to about 4" toward the middle of the visor to get at the clamp/clip etc. You will need to cut through the styrofoam too. The clip is not easy to take off and you will deform the foam. It will take two screwdrivers. It is hard to get back on too. I cut out the remaining plastic on the metal arm/shaft. The shaft can be slid out after disconnecting the wires from the lamp mirror. You dont have to take off the clip, but maybe you would have a way (better) to fix it w/out removing the clip. There is a paper disc that is tied to the wires before you can the shaft out. You need to untie it. I wish I had a better fix than just cutting off the existing platic off the shaft and wrapping it with soft wire then putting the clip back on. Now my visor falls down but it will stay up when pushed to block the sun. If I get a better answer/solution I will comment again. I did have to carefully hotmelt glue the styrofoam back together and then sew the fabric back on but at least I know how its put together now. Enjoy.

Posted on Jun 19, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Inside the visor there is a cover and clamp over the arm that basically puts tension on the arm preventing it from being floppy. The plastic arm that the visor rotates on pretty much desintegrates and/or in my case there is a flat part which also gets worn and rounded. I kind of doubt a plastic bond will hold up to the repair; but I may give it a try. Not sure with what though.Sun visor on 2005 Nissan Murano won't stay up/fall - e0e9fcf0-ddd4-4cd1-9178-dcc12046f047.jpg

Posted on Aug 07, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

BUY AMERICAN

Posted on Apr 10, 2013

  • joseweghor
    joseweghor Apr 10, 2013

    BUY AMERICAN

×

5 Suggested Answers

  • 26 Answers

SOURCE: 2005 Nissan Murano

There is a small tensioning screw that should be apperant near the bent metal visor swing arm. Sometimes this screw will loosen up with use. I am not sure what type of head is needed to tighten this screw on your model of car. (Phillips tip is most common.)
Tighten it up a little at a time until it is like you like it.
Presto.

Posted on Aug 22, 2009

  • 2976 Answers

SOURCE: driver side sun visor falls down

If you have anything on top of the visor, remove it. If there are any screws visible near the pivot rod, tighten them. You can remove the visor and slightly bend the pivot rod, inside the visor. You can just buy a new one and replace it yourself. It's only a few screws.

Posted on Sep 16, 2009

junmag
  • 175 Answers

SOURCE: Driver side sun visor on '04 Murano fall down.

a creative solution is to use velcro tape. a piece on the visor and a matching piece on the roof liner

Posted on Jun 02, 2009

  • 6 Answers

SOURCE: 2006 murano sun visor

I have found a few complaints at the following gov. site.
I have tried velcro which worked for awhile but now the glue won't stick to the roof material.

File a complaint here: (VIN # needed)
http://www-odi.nhtsa.dot.gov/ivoq/index.cfm

Search for the complaint - Visibility section
http://www-odi.nhtsa.dot.gov/complaints/index.cfm

Posted on Oct 16, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sun visor won't fully retract


look up in the corner of the visor where it mounts.. usually there is a small screw there .. raise the visor up in place and tighten the screw..it should stay up..if not ..use a bit of velcro on the visor and the headliner above it..cheap fix but it works..also invest in a windshield cover they are only a few bucks and work for other uses also.. they make a great emergency mat if you need to look under the car on naty ground(rain, snow, mud,etc)

Dec 08, 2013 | 2006 Saturn ION

1 Answer

The driver's sun visor won't stay up, it falls down


Already reported as being a repetitive problem with Murano vehicule owner eventhough they have it alreay replaced.
You can fight as long as you want with your dealer that this is a security issue no recall has been expressed about that so far.

I can say that some people switched the passenger side one with the driver side with little of convenience. I can't say more personnally.
The permanent fix being approx $250 unless you get it one in a scrap yard not knowing how long will be its life time! Up to you to make the decision.
Hope it will help
Dan

I have a 2003 Murano that just started having this problem a few weeks ago. As a quick fix, my husband and I switched the driver's side sun visor with the passenger's side sun visor (yes, everything is backwards now, but it's a minor inconvenience). It was very simple to do, and only took about 5 minutes. The cover pops right off to reveal two screws that hold the unit in place. Anyone could do it.
Meanwhile, we are searching local junkyards to try to find a replacement to avoid having to pay $250 (+) for a replacement visor. user_offline.gif

Dec 28, 2009 | 2005 Nissan Murano

1 Answer

Driver side sun visor falls down


If you have anything on top of the visor, remove it. If there are any screws visible near the pivot rod, tighten them. You can remove the visor and slightly bend the pivot rod, inside the visor. You can just buy a new one and replace it yourself. It's only a few screws.

Sep 16, 2009 | 2005 Nissan Murano

1 Answer

2005 Nissan Murano


There is a small tensioning screw that should be apperant near the bent metal visor swing arm. Sometimes this screw will loosen up with use. I am not sure what type of head is needed to tighten this screw on your model of car. (Phillips tip is most common.)
Tighten it up a little at a time until it is like you like it.
Presto.

Aug 22, 2009 | 2005 Nissan Murano

1 Answer

Sun visor falls down as I am driving


Look for a screw near where the arm comes down from the ceiling. Usually if you tighten this one or two screws it will stiffen up.

Some of these are not adjustable. Try a junk yard. They should not have too much trouble finding one your color and in good shape. It would not be very expensive.

Aug 20, 2009 | 2000 Toyota Celica

5 Answers

2007 Toyota Camry CE - Sun Visor (driver's side) won't stay up.


My 2008 Camry driver side sun visor just broke and it will not stay in the up position. is flops down about three inches just enough to bug the **** out of you while driving. another toyota problem that should be recalled since it seams to be common

Jul 30, 2009 | 2007 Toyota Camry

1 Answer

Sun visor droops down 2002 ram 1500


where the visor attaches to the roof there should be a plastic "cover" it can be removed but be careful to not break the tabs. You should be able to tighten the visor

May 05, 2009 | Dodge Ram 1500 Cars & Trucks

1 Answer

Sun visors won't stay flipped up.


most of the times on the visors if you look at were it mounts on the car you will see a small screw this is a set screw and if you tighten it just a little bit it should hold your visor up for you. but not all vehicles have a set screw as iam talking about. and if the impala dosent you need to get a compleat new visor
hope this helps you out

Apr 30, 2009 | 2006 Chevrolet Impala

2 Answers

Broken sun visor


On the plastic cover take a small screw driver and pry one of the open ends, in other words if you look at the cover carefully it is shaped like a U, pry on the top right side of the U to un-snap then rotate or twist the cover to remove.Then you can get to the screws that hold it into place/

Mar 25, 2009 | 2002 Ford Explorer

1 Answer

Sun Visors won't stay forward towards windshield


inside the sun visor there is a spring which is moving to side when you push down the spring pushes side so it will keep down when you want to push to the normal possition spring releces and keep to that possition any way i would like to advice you to replace sun visor.

Nov 28, 2008 | 2003 Toyota Highlander

Not finding what you are looking for?
2005 Nissan Murano Logo

14,175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...