Question about 1997 Dodge Stratus

Open Question

Need torque specs for oil pan on 1997 dodge stratus with 2.4l engine

What is the torque specs for oil pan? the engine is a 2.4l

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 218 Answers

SOURCE: I need some torque specs for the connecting rod

20 FT LBS + A 1/4 TURN

Posted on May 04, 2009

Ad
  • 1796 Answers

SOURCE: I need to know what the valve cover torque specs

Hi!!

My book says 89 in-lbs.

good luck

Posted on Mar 30, 2010

ZJLimited
  • 17970 Answers

SOURCE: I need torque specs for the head bolts on a 2004

For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Posted on Aug 02, 2010

Testimonial: "I appreciate your quick response. Thanks"

tunde007
  • 2382 Answers

SOURCE: I need to know where

Hi, the Oil Pressure Switch is located Under hood, center, rear right side of the engine area, mounted on lower block. The switch is covered by a triangular shaped heat shield that is secured by three bolts.

Posted on Jan 17, 2011

nighttrain_r
  • 444 Answers

SOURCE: torque specs and sequence for 97 dodge 2.4l stratus

for which procedure? i recommend spending the 10-15 bucks for a service manual. 90% of the questions i see here are detailed and answered in a typical service manual

Posted on Mar 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

Removal of oil pan 2003 dodge stratus


To get the oil pan off of your 2003 Dodge Stratus 2.7L engine, you must remove the following:
> Engine oil dipstick and tube
> Engine oil filter
> Structural collar (metal plate that bolts on the bottom between the oil pan and transmission housing)
> Exhaust cross-under pipe
> Torque converter housing cover
> The lower bolt attaching the A/C compressor to the oil pan
> Oil pan fasteners, Oil pan and gasket
Please note that attempting to remove the exhaust cross-under pipe can be a real challenge if you do not have the equipment to heat the nuts/studs that fasten it to the manifolds.
Non-availability of the required equipment in this case may mean that you will have to remove the exhaust manifold(s) to drill out broken studs.

May 16, 2012 | 2002 Dodge Stratus

1 Answer

Torque specs and sequence for 97 dodge 2.4l stratus


for which procedure? i recommend spending the 10-15 bucks for a service manual. 90% of the questions i see here are detailed and answered in a typical service manual

Mar 23, 2012 | 1997 Dodge Stratus

1 Answer

How do you get the oil pan off of a 2006 dodge stratus 2.7L


Hope this helps and please don't forget to rate!


  1. Disconnect the negative battery cable.
  2. Remove the engine oil dipstick and tube.
  3. Raise and safely support the vehicle.
  4. Drain the engine oil and remove the oil filter.
  5. Remove the structural collar.
  6. Remove the exhaust cross-under pipe.
  7. Remove the torque converter housing cover.
  8. Remove the lower bolt attaching the A/C compressor to the oil pan.
WARNING!!!!!
Be sure to remove the 2 bolts attaching the timing cover to the oil pan, as damage to the timing cover and/or oil pan may occur.
  1. Remove the oil pan attaching fasteners.
  2. Remove the oil pan and gasket.

May 08, 2011 | 2006 Dodge Stratus

2 Answers

I need to know how to tighten valve cover bolts on 97 dodge stratus


Welcome to FixYa.com What engine do you have?
Thank you for Using FixYa.com Kind Regards, Lee Your FixYa Expert and Master Technician
leedavidian_183.png

Feb 12, 2011 | 1997 Dodge Stratus

1 Answer

How do I replace the front engine mount(composit center-piece) on a 1997 Dodge Stratus ES(V6)?


Should be as "simple" as putting a wooden block under the oil pan and slightly jacking up the engine, to releave weight from the mounts. Then remove bolts and remove the mount.

Sep 12, 2010 | 1997 Dodge Stratus

1 Answer

Oil leek around plug on 99 dodge


A replacment pan would be the logical answer,with a new plug and gasket and tighten to the proper torque, as per factory specs.

Mar 06, 2010 | 1999 Dodge Stratus

1 Answer

Need to the torque for the oil pan for a 2005 dodge caravan with a 2.4 engine


Hello rkz3: The correct torque specs for the oil pan is 105 inch pounds. Should you need further help just ask.Thak you for using FixYa. Please rate the information as it helps a lot. Thank you again Roger

Apr 16, 2009 | 2005 Dodge Caravan

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

1 Answer

Transmission toque specs


The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Jul 27, 2008 | 2003 Dodge Stratus

Not finding what you are looking for?
1997 Dodge Stratus Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...