Question about Cars & Trucks

Open Question

Need ford 2.3 ltr engine torque specs. like crankshaft mains, connecting rod and cylinder head bolts

I have all the parts from machine shop and i want to make sure that i torque my engine perfectly to specs

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Ad
terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

  • 181 Answers

SOURCE: torque specs for cylinder head on a 200 ford focus

  1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
  1. Tighten all bolts in a single sequence to 50 Nm
  2. Back the bolts off 1/2 turn.
  3. Tighten the bolts in sequence shown to 50 Nm .
  4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
9 3 1 5 7
8 6 2 4 10 sequence for head


Spec for rod 38Nm

Posted on May 07, 2010

drsinister69
  • 2317 Answers

SOURCE: Does anyone have the bolt torque specifications

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

Posted on May 31, 2010

Testimonial: "This was the first time I used FixYa for help. I am very impressed. I got expert advice and very quickly. Many Thanks Lawrence"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

Flywheel bolt torque specs for a 1984 454 chevy engine


Second question about torque specs for this engine? A cheap shop manual will give you this and so much more. I always replace these bolts with ARP replacements on high performance or heavy pulling engines, so they have their own torque specs that come with the bolts.

Oct 28, 2016 | Chevrolet Cars & Trucks

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you


Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

1 Answer

What are the toyota torque specifications


It all depends on the year, best info is to call your local machine shop or check with your local parts stores to see if they have a Chilton or Haynes repair Manual on hand that has already been opened. If it has you can look inside and get the correct info. Hope this helps

Jul 16, 2014 | Toyota Highlander Cars & Trucks

2 Answers

What would make the car pulsate when breaking while the brakes and rotors appear good.


Normally this is caused by uneven rotors or drums, replacing brakes and not resurfacing drums

or rotors, or replacing drums or rotors, old brake fluid in system, not flushing out lines, dirty

brake fluid causing brake calipers to hang-up. inproperly installed brakes, not torqueing down

the bolts, loose bolts. good luck!

Jun 25, 2011 | 1999 Oldsmobile Aurora

1 Answer

How do i install my pacesetter headers on my 2000 chevy blazer and is there any trouble getting the manifold out. Will I be able to do this in the garage with basic tools?


as long as you have a torque wrench and torque it back down to the eng. specs. it is perfectly fine. as for the pace setter. make sure you correctly install the gaskets. and safley remove any objects from danger of heat.

I promote the safety of shop rules, and safety glasses.
~Dan Herzberg~

Feb 23, 2010 | 2000 Chevrolet Blazer

1 Answer

2.2 Camry cyl head removal


all the specs yuneed ypu can get at the parts store. get the head checked by a machine shop, and get new bolts, make sure mating surfaces are CLEAN
Dco not touch them at all finger leave residue

Oct 19, 2009 | 1995 Toyota Camry

1 Answer

Torque specs for big ends, mains, cam caps


found local Adelaide engine reconditioning shop that knows all about g200 twin cam EFI isuzu motors for parts and engine components ( pistons, rings, bearings etc. ) and machining, Chris Milton engine reconditioning. They will do machine work for me so then i can put it together.

May 23, 2009 | 1999 Isuzu VehiCROSS

1 Answer

Torque Settings on a 1994 BMW 318i?


The torque settings is more know as torque spec's, and it just means an exact measurement of how tight a paticular part is tightend. With a new engine, many differnt parts have differnt specs, but hands down the single most important thing would be the cylinder head to engine block torque. This is often done in a 3 step process, using a torque wrench, and a torque angle gauge. Are you planing on installing an engine yourself? I can get specs for you.

Mar 08, 2009 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...