Question about 2007 Chevrolet Silverado 2500HD

Open Question

2007 chevy 2500 4 wheel drive stuck in low 4x4 drive

Will not shift back to 2 wheel drive

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1998 chevy blazer won't go in to four wheel drive

It sounds like the encoder motor. That's the black plastic box on the driver's side of the transfer case. But just to make sure, the control module for the encoder motor is located behind the passenger side kick plate (inside the vehicle, passenger side, where your feet would be, outside side). Disconnect it for a few seconds and then reconnect it. If the problem still exists, you will have to repair or change your encoder motor. I grabbed one at a scrap yard for less than $100.00.

Posted on Jan 04, 2009

Ad
  • 2 Answers

SOURCE: 1996 suburban makes grinding noise in 2 wheel drive

sounds like the clip on the rear output shaft its probably broke. do this by removing the rear driveshaft, and the tail of the transfer case, there are 4 bolts holding it in place. then grab the output shaft and see if it has any front to back movement. if so pull it all the way to the rear and you should see a groove at the front part of the shaft where the clip goes. Then you should find the pieces fo the clip in the tail housing. One person said he found the replacement clip at a local tranny shop. I am calling the dealership parts counter for a new clip for my 97 Tahoe tomorrow. Hope this helps..

Posted on Mar 15, 2009

  • 2 Answers

SOURCE: My 98 s10 is stuck in 4 wheel drive low.

Pull the kick panel on the passenger side. there is a small box mounted there that is the computer that controls the actuator for the 4wd system. this is notorious for problems due in fact that the connector likes to pull out and away from the module. I had the same problem and the solution is simple.. take a long zip tie and get it between a few of the wires and around the module. tie it in and have a nice day.. it wont come off or try to pop out anymore and you should have no issues getting into 2wd, 4wd h, 4wd L.


Posted on Jun 21, 2009

redbeard00
  • 957 Answers

SOURCE: The four wheel drive quit working while driving in

Your truck should have a solenoid attached to the front axel (more so to the right side). Unplug the solenoid and probe the harness. It should be two wires if not tell me. But it should have twelve volts on one and ground on the other (with the 4wd in-gauged) If that is fine remove the solenoid and see if it actuates when put it into 2wd and 4wd. If that checks out then the problem is either somewhere inside the front axel or maybe the transfer case. But the way you described it I would start with the front axel.

Posted on Nov 11, 2009

gladys_neal
  • 334 Answers

SOURCE: I have a 2001 Chevy 2500 4X4. Four wheel drive not

Sounds like the chain in the transfer case has broke or the linkage is out of adjustment

Posted on Dec 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried it in 4x4 high and low out of curiosity and it was fine either way but now it won't let me shift back into 2 wheel drive. It's stuck in 4x4 low. Help please. Thank you in advance.


Stuck in 4x4 low please help! - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 2004 - 2008 F150
Jul 26, 2010 - My main problem right now is that i am stuck in 4x4 low. ... I did this and my truck locked in 4x4 low and would not come out. ..... Company and is not affiliated with the Ford Motor Company or its related companies in any way. 99 Expedition stuck in four wheel drive..help!
Dec 11, 2010
No 4x4 - Was Stuck in 4WD Low
Sep 12, 2007
97 explorer 4x4 problems switch wiring-stuck in 4wd
Aug 28, 2007
More results from www.ford-trucks.com

Oct 07, 2015 | Cars & Trucks

1 Answer

The low range light has come on its stuck on 4x4 and is slowing my truck down how do i fix this


you cannot run your truck normally in 4x4 low!!!! the low is designed to go slow slow.try shifting into neutral gear on column tap the high 4x4 then shift to reverse,back up 15feet then shift to drive.it should go into high 4x4 then if you want to go back to 2wheel high shift to neutral tap the 4x4 high until the light goes off,shift to reverse and back up 15feet then shift to drive and the 4wheel drive lights should all be off. then you'll be in 2x2 rear wheel drive. thank you for choosing fixya.com

Jan 22, 2011 | Ford Excursion Cars & Trucks

3 Answers

Wont shift back from 4x4 low, to 2x2


I also have a 2002 Envoy. Shifting to and from 4wh and 4wa can be done on the fly but shifting to 4wL has to be done stoped and while in neutral. Try that. Otherwise I'm afraid its a new computer for you. Its located under the left rear seat and you need a loan for one.

Sep 05, 2009 | 2002 GMC Envoy

1 Answer

Grinding in and out of 4 wheel drive


You say 'new' truck, 09? or new used? I have had 3 Fords, 3 w/ manual trans. case, if you go into 4x4 Low range, you must come to a complete stop before shifting the trans. case to 4x4 mode, and I always put trans (automatic) in neutral before slipping into 4x4, it engages smoothly, no grinding. 4x4 high range can be put in while moving, but I would let off the gas pedal, shift to 4x4 high range, then resume accelerating. If there is any grinding going on doing it as above, something isn't right. Check the trans. case fluid level also, to make sure that's not an issue.

Aug 15, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Noise in front diff


Three probable issues;
1-The transfer case is low or out of fluid.
2-The drive shaft may be out of alignment due to worn front or back U joints (thus the clunk on shift)
3-the shift lever is out of alignment with the shift mechanism on the transmission housing.

Mar 26, 2009 | 1989 Chevrolet K1500

1 Answer

1993 4X4 BLASER 4WHEEL DRIVE


Your blazer is equipped with a shift on the fly four wheel drive. That means that at speeds less than fifteen miles per hour you can shift into or out of four wheel drive by simply pushing the four wheel high button. If you wish to shift into four wheel low. Stop, put the transmission into park or neutral, and push the four wheel low button. Same procedure for shifting back out. Never shift into or out of four wheel low while moving. And be careful in four wheel low. At full throttle your still barely moving, you don't want to blow your engine up!

Dec 31, 2008 | 1994 Chevrolet S-10 Blazer

3 Answers

Ford F150 front tires won't engage in 4 wheel drive


look on fire wall pass. side you will see 2 parts with vacume lines attached 99 percent of the time that is what went i had the same problem

Dec 15, 2008 | 1999 Ford F150 Regular Cab

3 Answers

Can,t get truck out of 4x4 low range


try putting your truck in neutral and then shifting into 2 wheel drive shift on the fly does not apply to 4 low only 4 high and on electric shift models it wont shift unless your ****** is in neutral.

Aug 26, 2008 | 1999 Ford F250 Regular Cab

Not finding what you are looking for?
2007 Chevrolet Silverado 2500HD Logo

Related Topics:

588 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...