Question about 2004 Dodge Ram 1500

Open Question

2002 dodge dakota 4.7l v-8 error code P108 - 2004 Dodge Ram 1500

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sprintfanm
  • 2 Answers

SOURCE: I need information on how to change spark plugs on a 2004 Dodge Dakota 4.7 liter V-8

Make sure that you buy the correct type plugs(Champion RC12MCC4 or equivalent). Also it may be a good idea to have a flexible-extension for your ratchet.

Posted on Jun 26, 2008

csmock132
  • 4669 Answers

SOURCE: 2000 dodge durango,engine light on had it checked. p108

P0108 is a map sensor code.

Posted on May 03, 2009

  • 14036 Answers

SOURCE: 96 dakota p1391 error

intermittent loss of ckp or cmp.problem is in the distributor.make sure rotor not loose or distributor hold down bolt loose.camsensor on the distributor.also check to see if crank sensor is loose and out of adjustment.

Posted on Jun 07, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: Error codes P0442 and P0455 in Dodge Dakota 2001

Hello shoretex...Yes sir you can repair this yourself...
p0442 is medium leak detected ...p0456 is small leak....and p0440 is a general evap system failure.. evap codes are a common thing. gas caps are an inexpensive place to start. There are two types of evap hoses on the Dodge... hard plastic and soft rubber.... before you replace parts check the soft rubber first at the evap cans and pump located about a foot in front of the gas tank fill pipe on trucks located next to the transfer case or right behind the trans on the driver side. hard plastic lines will brake or rub through...check spots where lines come in contact with anything. this is a common thing with older trucks...hair line cracks will kick a p0442 code, and a p0445 code...When you find a leak, repair it, and rescan...sometimes there are several leaks, continue with inspection and repairs until you get it all fixed up.... Remember..start at simple and work from there...
i will post the evap. system in more detail to help you troubleshoot the problem.
EVAP System: The Evaporative Emission (EVAP) Control system used on all vehicles is the charcoal canister storage method. This method transfers fuel vapor from the fuel tank to an activated carbon (charcoal) storage device (canister) to hold the vapors when the vehicle is not operating. When the engine is operating, the fuel vapor is purged from the carbon element by intake air flow and consumed in the normal combustion process. The evaporative system includes the following components: *Fuel tank *Evaporative emission canister vent solenoid *Fuel tank pressure sensor *Fuel pipes and hoses *Vapor lines *Fuel cap *Evaporative emission canister *Purge lines *Purge valve solenoid EVAP System Operation: The EVAP purge solenoid valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a ground to energize the EVAP purge solenoid valve (purge on). The EVAP purge solenoid control is Pulse Width Modulated (PWM) or turned on and off several times a second. The EVAP canister purge PWM duty cycle varies according to the operating conditions determined by the mass air flow, the fuel trim, the engine coolant temperature, and the intake air temperature. For certain EVAP tests, the diagnostic will be disabled if the TP angle increases to above 75% . The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring for vacuum decay. The fuel level sensor input to the PCM is used to determine if the fuel level in the tank is correct to run the EVAP diagnostic tests. To ensure sufficient volume in the tank to begin the various diagnostic tests, the fuel level must be between 15% and 85% . The PCM monitors the fuel tank pressure/vacuum level via the fuel tank pressure sensor input. Results of Incorrect Operation: Poor idle, stalling and poor driveability can be caused by the following: *Malfunctioning purge solenoid. *Damaged canister. *Hoses/lines split, cracked and/or not connected properly. Evidence of fuel loss or fuel vapor odor can be caused by the following: *Liquid fuel leaking from the fuel lines *Cracked or damaged canister *Inoperative canister control valve Vacuum hoses that are: *Disconnected *Mis-routed *Kinked *Deteriorated *Damaged The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM monitors vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid are turned on, allowing engine vacuum to draw a small vacuum on the entire evaporative emission system. After the desired vacuum level has been achieved, the EVAP purge solenoid is turned off, sealing the system. A leak is detected by monitoring for a decrease in vacuum level over a given time period, all other variables remaining constant. A small leak in the system causes DTC P0442 to be set. If the desired vacuum level cannot be achieved in the test described above, a large leak or a faulty EVAP purge solenoid is indicated. This can be caused by the following conditions: *Disconnected or faulty fuel tank pressure sensor. *Missing or faulty fuel cap. *Disconnected, damaged, pinched, or blocked EVAP purge line. *Disconnected or damaged EVAP vent hose. *Disconnected, damaged, pinched, or blocked fuel tank vapor line. *Disconnected or faulty EVAP canister solenoid. *Disconnected or faulty EVAP vent solenoid. *Open ignition feed circuit to the EVAP vent or purge solenoid. *Damaged EVAP canister. Any of the above conditions sets DTC P0440. A restricted or blocked EVAP canister vent path is detected by drawing vacuum into the EVAP system. The PCM turns off the EVAP vent solenoid and the EVAP purge solenoid (EVAP vent solenoid Open, EVAP purge PWM 0% ). The PCM monitors the fuel tank pressure sensor input. With the EVAP vent solenoid open, any vacuum in the system should decrease quickly unless the vent is blocked. A blockage is caused by the following conditions: *Faulty EVAP vent solenoid (stuck closed). *Plugged, kinked, or pinched vent hose. *Shorted EVAP vent solenoid driver circuit. *Plugged evaporative canister.

Good luck shoretex, hope this helps...please take time to rate me a fixya.

Posted on Jul 20, 2009

  • 181 Answers

SOURCE: 2002 dodge dakota code p0733 p0734

This code means gear ratio dont match from in to out on transmission in 3rd po733 4th po734 first thing to do is do a filter change and replace the fluid.LOOK for metal shavings. If you see alot could be interal problems. I have seen this fixed by a good trans flush Hope this helps

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix codes p31,p51, and p136 on a dodge dakota 2002 3.9


Try going into your local auto parts store normally if your nice they will help you out.

Oct 06, 2014 | 2002 Dodge Dakota Club Cab

1 Answer

Error code PO303 on 2002 dodge dakota


cylender 3 mis fire check plugs and wires first then do comprission test

Nov 20, 2013 | 2002 Dodge Dakota Club Cab

1 Answer

2002 dodge dakota quad cab error codes P0442 & P0446


They are common Generic Codes you can find anywhere on the internet

PO442-Evap System (Small Leak)

PO 446- Evap System Vent Control Circuit Malfunction

Oct 26, 2012 | Dodge Cars & Trucks

1 Answer

Engine code on a 2002 dodge dakota with a 3.9 code p 1762


p1762 is governor pressure to low or to high, if you can not check the pressure. you may have to take it to a dodge dealership to get it fixed.<!-- from fixya rte -->

Aug 16, 2010 | 2002 Dodge Dakota Club Cab

1 Answer

O2 sensors how to replace in 2002 dodge dakota 3.9


all you need is a 7/8 wrench. the o2 sensors are located in the exhaust system. just un plug them and unscrew them. not that hard to do if doing it for the first time.

Mar 30, 2010 | 2002 Dodge Dakota Club Cab

1 Answer

Got a 2002 Dodge Dakota 4x4 Quad 4 door witha 5.9


this indicates that a misfire has occurred in cylinder number three.

Mar 03, 2010 | Dodge Dakota Cars & Trucks

1 Answer

My dodge dakota idles erractically


Check for any air leaks on the intake or manifold. It could also be an intake gasket, but then you would most likely have an error code (check engine light coming on). Some other thoughts, fuel pressure could be erratic (check filter and line pressure). best wishes

Aug 22, 2009 | 2002 Dodge Dakota Club Cab

1 Answer

Error codes 0442 and 0445


Hi..my name is Keith..and the error code P0442 means...Evaporative emission control system,small leak detected ...and error code P0445 means....Evaporative emission control system,short in purge control valve circuit..i hope this has helped

Jul 04, 2009 | 2002 Dodge Dakota Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...