Question about 2000 Mazda 626

Open Question

How to replace valve cover gasket 2000 mazda 626

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 47 Answers

SOURCE: Check Engine light code 1506

this code indicates under-speed error has ocurred.
sets when PCM detects idle speed is 100 RPM lowerthan expected for 14 sec while break pedal depressedand steering wheel is straight ahead.

possible causes: IAC valve failure,intake leak,throttle body failure,opens or shorts in wiring between IAC and PCM.

Posted on Sep 16, 2009

Ad
  • 2 Answers

SOURCE: Which Mazda diesel engine do I have? RF, RF-CX or RF-N

The engine is a RF- CX the CX denotes comprex pressure wave supercgarger

Posted on Dec 24, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

  • 1 Answer

SOURCE: oil leak in my 98 mazda protege

Could be a rear main seal.

Posted on Feb 01, 2010

  • 244 Answers

SOURCE: How to replace valve cover gaskets on a 2000 mazda

just look at the valve covers some are held in place with 6 bolts some only 3 do one at a time and keep working area clean and free of dirt n grease. clean valve cover good and have clean hands when handling gasket, and there your done just replace and bolt down , check bolts again for tightness in a couple weeks.

Posted on Apr 25, 2010

Testimonial: "Thanks for the quick reply...This info is priceless!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 mazda 626 lx 2.0 the car ideled rough with ac or defroster replaced front and rear motor mounts,now it idels rougher and vibrates the car.


These cars tend to have bad spark plug wires, they will arc where the boot goes down into the valve cover.Check to make sure there is no oil in the spark plug well,if the is you will need to replace valve cover gasket and orings.Souds like you need a new set of plugs and wires.Look for corosion where the wires connect to distributor also as you may also need a new cap and or coil.

Mar 27, 2011 | Mazda 626 Cars & Trucks

1 Answer

Hi is it a hard job to replace gasket on a 1990 mazda 626 2ltr water pump


what gasket are you talking about the head gasket? if so its about a week to do the job typically cause have to take heads off and can figure run into multiple problems along the way and need a new valve cover gasket cause it will fall apart and a new water pump and new water pump gasket

Sep 25, 2010 | 1990 Mazda 626

1 Answer

My Mazda 626 is running rough and has sparks coming from the sides of the spark plug leads also i can hear air coming from the engine bay.


Remove you spark plug leads and see if they are soaked with oil. If so you will have to remove your valve covers and replace the valve cover gaskets. They tend to leak oil into the area of the spark plug holes. You will have to replace the plug wires also. Just replace them one at a time so you will not losthe firing order.Hope this helps. Leave comment.

Jul 11, 2010 | 1992 Mazda 626

1 Answer

Throuble 626 mazda 1994, oil in top cylindre head.


sound's like the valve cover gasket is leaking

Jun 05, 2010 | Mazda 626 Cars & Trucks

2 Answers

99 mazda 626 lx -i have a slow oil leak. only leaks when i drive.


It sounds like it's actually burning the oil, rather than leaking it then, I'm assuming that your usage is a lot more than the drop you mention. The entire car has 234k on it? (or did you mean just the trans?) With that many miles I wouldnt be surprised if your valves are letting a little oil slip into the combustion chamber. If the usage is bad enough, it may be time for a valve job, or even a rebuild.

Apr 27, 2010 | 2000 Mazda 626

1 Answer

How to replace valve cover gaskets on a 2000 mazda millenia w/ 2.3 DOHC Supercharger?


just look at the valve covers some are held in place with 6 bolts some only 3 do one at a time and keep working area clean and free of dirt n grease. clean valve cover good and have clean hands when handling gasket, and there your done just replace and bolt down , check bolts again for tightness in a couple weeks.

Apr 25, 2010 | 2000 Mazda Millenia

1 Answer

2000 mazda 626 check engine light went on . code


probley not egr valve it probley egr control solenoid or wiring

Apr 11, 2010 | 2000 Mazda 626

1 Answer

Check Engine light code 1506 for 2000 Mazda 626


Here is some problem in your car wiring, some of the jack is lose or unplug near relay box,

Sep 16, 2009 | 2000 Mazda MPV

2 Answers

Check Engine light code 1506


Dear Sir,

P1506 error refers to Idle Air Control System Overspeed Detected.
So solution is check your Air control system wires,and check air control speed once again.
If this not solves your problem back with the result,leave a feedback we happy to help you.


Have a nice day

Good luck


Sep 16, 2009 | 1995 Mazda 626

1 Answer

Stalled out like it was out of fuel or bad timing. Turned over and puffed and ghugged for a minute now wont run. Replaced plugs, wires. It has good spark and getting enough fuel through the rail. Maybe a...


Oh, great...just bought a '95 626 for my daughter and we're going thru the same problems. Was told to replace valve cover gasket and plugs and wires. replaced filters and put in new oil and fluids. Also read somewhere it could be alternator issues.

Jul 16, 2009 | 1995 Mazda 626

Not finding what you are looking for?
2000 Mazda 626 Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...