Question about 2010 Dodge Caliber

1 Answer

Front caliper will not come out on my 2010 dodge caliber

Pulled out the 2 main caliper bolt yet it still wont come out

Posted by on

Ad

1 Answer

Only the rust lip on the rotor holding it on

Sand down some of the outer edge or just
pull the caliper toward you, to compress the piston

Those rotors will need machining

Try the Raybestos Ceramic Pads

Posted on Dec 08, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 49 Answers

SOURCE: front spindle caliper mount holes stripped,any fixes

they make heily coils to either down one size or up one size .make sure you put red lock tight on heily coil when you instal in the striped hole.make sure holes are CLEAN.

Posted on Feb 21, 2009

tse22
  • 103 Answers

SOURCE: Changing Rear brake pads 2005 dodge grand caravan

There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

Posted on May 13, 2009

  • 109 Answers

SOURCE: 98 dodge durango front brakes calioers wont compress decompress

YOU NEED TO REPLACE THE PROPORTIONING VALVE!!
DOES IT HAVE ABS BRAKES ON THE FRONT? (MOST DURANGOS ONLY HAVE ABS ON REAR ONLY)

Posted on Jun 30, 2009

  • 15 Answers

SOURCE: dodge ram 2500 4x4 caliper bolts won't come loose

they are usually loctited from the factory,you will have to heaten the bolt,use a small torch,or a good heat gun on the head of the bolt only,be very carefull not to burn the rubbers on the bolts. one of the small solder torches works well,it takes a few minutes each bolt,but you woon't burn the rubbers.

Posted on Oct 10, 2009

  • 1 Answer

SOURCE: what size caliper bolt for front brake assembly on

The retainer bolts in a Durango 2000 are 7 MM hexagonal heads,otherwise known as 7 MM Allen wrench.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I change my 10amp fuse from fuse box but radio still wont turn on 2010 dodge caliber


Don't worry I'm sure you will get the solution of your problem, just check the link I attach DODGE CALIBER 2010 SERVICE REPAIR MANUAL

Oct 11, 2017 | 2010 Dodge Caliber

1 Answer

How to replace Front brakes 2010 Dodge journey?


Hi Steve, I'm glad to help. First, take of the front wheel's. Then press the calipers inward, this will make it easier to remove the calipers. Next, remove the calipers with the old pads. PUSH the calipers all the way back and install the new pads. There are only 2 bolts holding a single caliper. NEXT, If you plan to replace the rotors. NOTE: Which I recommend. You'll need to remove the bracket that holds the caliper, there is only 2 bolts holding it to the spindle. NEXT, Remove the rotor and relace with new rotors. Note: sometimes the original rotors are stuck because of rust you'll need to tab them off with a hammer. After installing the new rotors, it helps to put one nut on to hold the rotor in-place. Then re-install the bracket, the caliper and thighten the bolts. CAUTION: DO NOT try to drive the vehicle until pumping the brakes and they are very firm. Install the wheels and your good to go. Hope this helps and have an awesome day Steve!

May 03, 2014 | 2009 Dodge Journey

2 Answers

My front brake pads keep holding up...when I drive they get really hot and wont release...what's the deal?


Your brake caliper or your brake hardware is sticking. Pull it apart(two bolts) and push the caliper back in with a spreader or a c-clamp. The grease the brake hardware(where the bolts go in). That might do the trick. If you have a hard time getting the caliper peston back in then you need to replace it and bleed the brake system.

Jul 01, 2011 | 1995 Toyota Tercel

1 Answer

How do i remove the front brake calibers on a 1991 chevy 4x4 k1500


The front brake calipers are held on by two long bolts with female 3/8" Allen heads on them The socket needed will be a 1/2" Drive 3/8" Allen. The bolt heads are at the rear of the caliper so leave the steering unlocked so you can turn the brake rotor in the direction that allows access. It will be esier to remove the caliper if you depress the caliper piston with a large screwdriver before trying to remove it after the bolts are removed. See bolt picture below.

emissionwiz_178.jpg

May 12, 2011 | 1991 Chevrolet K1500

1 Answer

How do you remove the front disc brakes?


To remove the front disc brakes , you must remove the break caliber assembly . Keep in mind that on some brake calipers a special Torx Drive T40 or T45 must be used to remove the caliber bolts from the spindle assembly . Also , Allen (Hex) bolts are sometimes used . Be sure you have the right tools .
1. Properly block both rear wheels at the front in the back of each wheel.
2. Loosen the lug nuts on both front wheels one turn on each nut.
3.Jack up and support the front of the car on Jack stands with the wheels one to 2in. off the ground.
4. Remove the two bolts on the inside of the caliber the secure it to the spindle .
5.Once the bolts have been removed the caliber should pull straight away from the rotor and spindle assembly .
6.Remove your old brake pads , clean the assembly , properly lubricate the moving parts as necessary , especially the floating sleeve as the assembly is called a floating caliber which means half of the Caliper is bolted to the spindle (inner) but the other half floats (outer).
7.Use a large see clamp centered between the caliper piston and caliper housing to push the piston all the way back into the caliber cylinder by turing (1 turn at a time) the screw until the piston is flush with the caliber face .
8. Install your new brake pads .
9. use the reverse procedure to assemble everything back together. Good luck and be safe....

Sep 05, 2010 | 1988 Chevrolet Suburban

1 Answer

How do i change my front brake pads? do I have to remove the 2 main caliber housing bolts or is there an easier way?


There is no easy way. Here is what you do. Prepare a rope or wire before you remove the Caliper. Have this rope or wire hanging down available to tie off the caliper when removed.
Slide the caliper off, remove the pads and replace the Hardware. The Brake Quiet compound is a good product to use. Undo the Master cylinder cap and leave open.
Take an old pad and **** it up to the caliper piston, then use a C clamp or wood block to drive the piston flush into the caliper.
Either refinish or replace the rotors and then slide the caliper over the rotor and use the new hardware. Bolt into place.
You may still need to bleed the brakes, check Master Cylinder level and replace cap.

Apr 17, 2010 | 2004 Ford Expedition

2 Answers

2007 dodge grand caravan


according to the service manual there are two bolts hold the caliber to tthe adapter plate and the caliper should roll up and out. the only problem i could imagine is if the pads are hanging in the adapter

Nov 21, 2008 | 2005 Dodge Grand Caravan

Not finding what you are looking for?
2010 Dodge Caliber Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...