Question about Cars & Trucks

Open Question

Peugeot expert cant remove inlet manifold with bolts removed

Remove inlet manifold

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Can't remove intake manifold on 94 Chevy 5.7L TBI

Yes, the allen bolts need to come out.

Posted on Jan 05, 2009

Ad
  • 1861 Answers

SOURCE: removing starter from toyota corolla 1998

No. Removal of the intake manifold is not an attractive option.
...That will cost you more time and money in the long run.
You will need to replace the intake manifold gasket, and several others.

Posted on Jan 15, 2009

  • 1 Answer

SOURCE: How to access plugs on 2002 stratus RT 3.0 V6

This web site has the steps to taking the manifold off http://home.pacbell.net/fong8/gstuff/tjc_plenum.htm

Posted on Mar 26, 2009

  • 67 Answers

SOURCE: 2005 Hyundai sonata 6 cylinder remove intake

there are 3 bolts in the back1 on left 1 in middle and 1 on the right. hope that helps

Posted on Apr 18, 2009

venexcsd
  • 1185 Answers

SOURCE: FOCUS 1.6 ZETEC CLIMATE TDCI 2006- FAULT CODE P242F

If the cat was blocked you would have noticed a massive power loss and your speed would have been down to - 40kph

If that was the case then yes the cat has collapsed and needs replacing

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Exhaust manifold


Reach from under the car after exhaust pipe is removed from manifold.

Apr 22, 2014 | 2001 Peugeot 206 1.6

1 Answer

Manifold absolute pressure switch


The MAP switch is located on the underside of the inlet manifold on the front. Remove the inlet elbow and you would see it. Mostly it is made by Bosch and is fitted with one small bolt. Buy a Haynes Workshop Manual of 406 (PN 3982) in the long run.

Feb 11, 2014 | 1999 Peugeot 406

1 Answer

Need to remove the water pump


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


WATER PUMP REMOVAL
  1. REMOVE RH ENGINE UNDER COVER
  2. DRAIN ENGINE COOLANT
  3. REMOVE GENERATOR (See page CH-8)
91329747


  1. REMOVE INTAKE MANIFOLD STAY
  1. REMOVE WATER INLET PIPE
(a) Disconnect the following hoses: 91329748


(1) Water inlet hose (2) Heater inlet hose (3) Water bypass hose 91329749


(b) Remove the bolt, water inlet pipe and 0-ring.
  1. REMOVE OIL DIPSTICK GUIDE AND GENERATOR ADJUSTING BAR
(a) Remove the oil dipstick. (b) Remove the mounting bolt of the dipstick guide clamp and generator adjusting bar. 91329750


(c) Pull out the dipstick guide. Plug the guide installation hole of the oil pump. (d) Remove the 0-ring from the dipstick guide. 91329751


  1. REMOVE WATER PUMP
    • Remove the bolt, 2 nuts and water pump.

Jan 02, 2011 | 1992 Toyota Tercel

1 Answer

Location of thermostat on 2002 olds alero 2.2


Thermostat Removal & Installation 2.2L Engine To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt.
      1. Tighten bolt to 89 in lbs (10 Nm).
    • Exhaust manifold if equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L Engine To Remove:
Thermostat assembly 2.4L 87953024.gif

  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield.
  3. Remove the coolant inlet housing mounting bolts through the exhaust manifold.
  4. Raise and safely support the vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove wheel and tire assembly.
  7. Remove the engine splash shield.
  8. Remove the mounting bolts from the transaxle-to-engine block support. Remove the support.
  9. Remove the coolant housing pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the coolant housing pipe.
  3. Install and secure the transaxle support-to-engine block mounting bolts.
  4. Install the engine splash shield.
  5. Install the wheel and tire assembly.
  6. Install the coolant inlet housing stud to the oil pan.
    • Tighten to 19 ft lb (26 Nm).
  7. Lower the vehicle.
  8. Install the coolant inlet housing bolts through the exhaust manifold.
    • Tighten the coolant inlet housing bolts to 10 ft lb (14 Nm).
  9. Install the exhaust manifold heat shield.
  10. Fill the cooling system.
  11. Inspect the system for leaks.
3.4L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat.
To Install:
  1. Install the thermostat and housing outlet.
  2. Install the thermostat housing bolts.
    • Tighten the thermostat housing bolts to 18 ft lb (25 Nm).
  3. Install exhaust crossover pipe.
  4. Connect the surge tank line fitting to the coolant outlet.
    • Tighten the fittings to 15 ft lb (21 Nm).
  5. Install the air cleaner.
  6. Fill the cooling system.
  7. Inspect the system for leaks
prev.gif next.gif

Oct 14, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

I cant find where the thermostat goes to replace it on a 2.4L engine. For a buick skylark


Very odd arrangement. You have to reach thru the exhaust manifold. I will paste instructions from Autozone.com below.

  1. Disconnect the negative battery cable.
  2. Properly drain and recover the coolant to a level below the thermostat.
  3. Unfasten the coolant inlet housing bolt, which is accessible through the exhaust manifold.

d8f2a03.jpg

Fig. Fig. 5: View of the thermostat and related components-2.4L engine

  1. Raise and safely support the vehicle.
  2. Remove the radiator outlet pipe stud.
  3. Remove the second coolant inlet housing bolt, then remove the coolant inlet housing.
  4. Remove the thermostat, then clean the old gasket material from the mating surfaces.

To install:
  1. Position the thermostat in its correct location, then install the coolant inlet housing using a new gasket. Tighten the retaining bolt to 19 ft. lbs. (26 Nm) on the 2.3L and 10 ft. lbs. (14 Nm) on the 2.4L engine.
  2. Install the radiator outlet pipe stud.
  3. Carefully lower the vehicle.
  4. Install the coolant inlet housing bolt through the exhaust manifold.
  5. Properly fill the cooling system.
  6. Connect the negative battery cable, remove the radiator cap, then start the engine. Allow the engine to run with radiator cap removed, until the upper radiator hose becomes hot (thermostat open). With the engine idling, add coolant to the radiator until the level is up to the bottom of the filler neck.
  7. Install the radiator cap, making sure the arrows line up with the overflow tube.

Sep 19, 2010 | 1998 Pontiac Grand Am

1 Answer

Need to remove the turbocharger from truck to replace oil cooler. Am unable to get it out. It is a 2003 ford 250 superduty tubo diesel 6.0 litre


1 - Remove the turbocharger intake tube
2 - Disconnect the charge air cooler inlet pipe
3 - Remove the push pins on turbo cowl
4 - Disconnect the turbo VGT solenoid
5 - Remove the oil supply tube
6 - Using the special tool, remove the oil feed tube
7 - Remove clamp from the turbo down pipe
8 - Remove the clamp from the turbo inlet
9 - Loosen the exhaust inlet pipe-to-EGR cooler clamp
10 - Loosen the RH & LH exhaust inlet pipe-to-exhaust manifold nuts
11 - Remove the rear turbocharger mounting bolt
12 - Remove the front mounting bolts
13 - Position the turbocharger and remove the turbocharger drain tube
14 - Remove the turbocharger

If you cant do it with these instructions put down your wrench and take to a dealership for a professional to work on it

Sep 03, 2010 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

How to replace head gasket on 1999 2.5 cyl ford ranger


Cylinder Head Removal
  1. Disconnect the battery ground cable
  2. Relieve the fuel pressure.
  3. Drain the cooling system. Disconnect the three way catalytic converter Loosen the water pump pulley bolts.
  4. Remove the drive belt.
  5. Remove the water pump pulley, fan and clutch assembly.
  6. Remove the intake manifolds
  7. Remove the ignition wires from the spark plugs .
  8. Remove the spark plugs; .
  9. Remove the oil level indicator tube
    • Remove the bolt.
    • Remove the oil level indicator tube.
    • Remove the EGR valve to exhaust manifold tube
    1. Remove the valve cover
    1. Remove the drive belt .
    1. Recover the A/C refrigerant; refer to Disconnect the engine control wiring from the A/C compressor
    2. Remove the A/C compressor mounting bracket (2882) with the power steering pump (3A674) attached and position out of the way.
    3. Disconnect the engine control sensor wiring connector from the generator
    4. Disconnect the (1) lower radiator hose and the (2) water pump inlet tube
    5. Remove the upper radiator hose
    6. Remove the water pump inlet tube.
      • Remove the bolts.
      • Remove the water pump inlet tube.
    7. Remove the generator.
      • Remove the bolts.
      • Remove the generator.
    8. Remove the generator mounting bracket.
      • Remove the bolts.
      • Remove the bracket.
      1. Remove the ignition wire and bracket; refer to Section 303-07A .
      1. Remove the outer timing belt cover; refer to the procedure in this section.
      1. Remove the timing chain/belt (6268); refer to Timing Drive Components—Timing Belt in this section.
      1. Remove the exhaust manifold (9430); refer to Exhaust Manifold in this section.
      1. Remove the cylinder head .
        • Remove the bolts and discard. (should get new ones)
        • Remove the cylinder head.
        • Remove the head gasket and discard.
Installation
  1. Clean all gasket mating surfaces.
  1. Install new gaskets as necessary.
    • Use new cylinder head bolts.
  1. Follow the removal procedure in reverse order.
  1. Tighten the bolts in sequence, in three stages, to 70 Nm (51 lb/ft).
    • Stage 1: Tighten all bolts to 70 Nm.
    • Stage 2: Retighten all bolts to 70 Nm.
    • Stage 3: Tighten all bolts an additional 90-100 degrees.
  2. Install generator bracket. Install bolts in four stages.
    • Stage 1: Hand-start bolt 1.
    • Stage 2: Install and tighten bolt 2.
    • Stage 3: Install and tighten bolt 3.
    • Stage 4: Tighten bolt 1.
  3. Install the A/C compressor mounting bracket. Install the bolts and the stud.
    • Tighten the M10 bolts and stud to 48 Nm (35 lb/ft).
    • Tighten the M8 bolt to 25 Nm (18 lb/ft).

Mar 10, 2010 | 1999 Ford Ranger SuperCab

2 Answers

How to change an exhaust manifold leak 7.5L


Right-Hand
Removal
  1. Remove spark plug heat shield (12A406).
  1. Remove distributor to spark plug wires (12286) using Spark Plug Wire Remover T74P-6666-A.
    1. Disconnect muffler inlet pipe.
    1. If equipped with secondary air injection, disconnect the secondary air injection check valve tube (9B480).
    1. Remove attaching bolts and right exhaust manifold (9430).
    1. Inspect joint faces for signs fo exhaust leaks, cracks or any defect that would make exhaust manifold unfit for use







Left-Hand Removal






1. Remove oil level indicator tube (6754).
  1. Remove spark plug heat shield.
  1. Remove distributor to spark plug wires using Spark Plug Wire Remover T74P-6666-A.
  1. Disconnect EGR valve to exhaust manifold tube (9D477). If equipped with air injection, disconnect the secondary air injection check valve tube.
  1. Disconnect muffler inlet pipe.
  1. Remove attaching bolts and exhaust manifold (9431).
  1. Inspect joint faces for signs of exhaust leaks, cracks or any defect that would make the exhaust manifold unfit for use.
Installation
  1. Clean mating surfaces of right exhaust manifold or left exhaust manifold and cylinder head (6049). Clean mounting flange of right exhaust manifold or left exhaust manifold and inlet pipe(s). Clean mounting surface for air injection tube or right exhaust manifold. Apply light film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to right exhaust manifold or left exhaust manifold.
  1. Position right exhaust manifold or left exhaust manifold on cylinder head. Install attaching bolts and washers, starting at fourth bolt hole from front of each right exhaust manifold or left exhaust manifold. Tighten bolts to 34-47 Nm (25-35 lb-ft), working from center right to both ends.
    1. Position inlet pipes to right exhaust manifold or left exhaust manifold. Install attaching nuts and tighten to 34-47 Nm (25-35 lb-ft).
    1. Position the secondary air injection check valve tube and the secondary air injection tube gasket (9C435) at rear of right-hand exhaust manifold. Install attaching bolts and tighten to 19-25 Nm (14-18 lb-ft).
    1. Attach the secondary air injection manifold tube (9B449) to left-hand exhaust manifold fitting (located under EGR tube). Tighten nut to 30-40 Nm (22-30 lb-ft).
    1. Attach the secondary air injection check valve tube to rear of right-hand cylinder head. Tighten bolts to 75-85 Nm (56-62 lb-ft).
      1. Connect EGR valve to exhaust manifold tube to left exhaust manifold, if removed. Tighten nut to 53-72 Nm (39-53 lb-ft).
      1. Install spark plug heat shield and distributor to spark plug wires.
      1. Install oil level indicator tube to left exhaust manifold, if removed. Tighten nut to 13-24 Nm (10-18 lb-ft).
      2. Start engine (6007) and check for exhaust leaks.







b913da4.gif
28b39c6.gif
Hope this helps you...WF †

Mar 10, 2010 | 1996 Ford F250 Crew Cab

2 Answers

Peugeot Expert EGR Valve


EGR is located at the back right hand side of the engine follow the silver pipe from inlet manifold , back and where it joins at the back of the lump , thats the egr!!

2x 8 mm bolts hold it in place + 5 mm allen screw if present secures a braket for wiring

Jun 15, 2009 | 2006 Peugeot 604

1 Answer

How do you remove the heater matrix on a peugeot expert


window wipers off remove trim and there is 10 mm nuts, remove them, remove speedo cluster and radio etc, there is 2 10mm bolts below each end in footwells at end bottom of dash, 1 bolt below your ash tray in front of gearstick, u got to get gear stick surround out.

Mar 30, 2009 | 2006 Peugeot 604

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...