Question about 2001 Chevrolet Blazer

Open Question

2001 chevy blazer alternator went bad how do i remove it

What are the steps to remove an alternator in a 2001 Chevy Blazer?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Engine replacement 1996 Chevy Blazer

I just replaced my engine in my 1996 blazer myself. Body need not come off, but what an ordeal if its a 4 X 4.

Posted on Oct 01, 2008

Ad
  • 625 Answers

SOURCE: fan clutch removal

crank the engine and see wich way the fan turns and that's the way to loose it if turns to rt it looses to rt if to the left it looses to the left

Posted on May 28, 2008

  • 58 Answers

SOURCE: 2001 chevy blazer

It is inside the transmission. It is called a reaction sun shell, it strips out, which causes the grind noise your talking about.

Posted on Dec 21, 2008

  • 5 Answers

SOURCE: 2000 Chevy Blazer

i am working on a s 10 of the same yaer and problem i will post my results after tomorrow when i have finished the job i bout this truck cause of the forum i own one that is a great one and this one is for experimental purpose i will let u know so far you cant lift the motor with a jack or a hoist so we r going another route in the mornin

Posted on Dec 27, 2008

emissionwiz
  • 76164 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace power window in driver door of 2001 chevy blazer?


are you replacing the power window regulator ?follow this u-tube link for excellent step by step instructions , if not the regulator let me know and i'll see if i can help further
How To Install Replace Power Window Regulator Chevy S10 Blazer GMC S15...

Sep 19, 2014 | 2001 Chevrolet Blazer

1 Answer

Starter on 2001 chevy blazer wont come by bframe


place the front of the car on jack stands than take off the front passenger side wheel and remove the starter from the inner wheel well

Oct 24, 2012 | 2001 Chevrolet Chevrolet Blazer

1 Answer

How do I change wiper blades 2001 Chevy blazer


Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage.
Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pQJ39h
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pJlPaV
  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

    Jan 15, 2011 | 2001 Chevrolet Blazer

    1 Answer

    99 Chevy Blazer loosing power while driving


    Check for power on the small wire on the alternator plug. If it has power than you might of just got a bad alternator.

    Jul 25, 2010 | 1996 Chevrolet Blazer

    1 Answer

    2001 Chevy Blazer Stalls on turns and deceleration.


    this could be a tuffy possible fuel pump in take more likely elec is check engine light on go back to auto zone check for codes, check engine power & grounds

    Aug 30, 2009 | 2001 Chevrolet Blazer

    1 Answer

    Removing fuel meter from plenium on 01 chevy blazer


    You are missing a bolt, or you will have to remove one of the heads.

    Dec 29, 2008 | 2001 Chevrolet Blazer

    3 Answers

    2003 Chevy Blazer won't start


    have the computer checked out. may need reprogramming and have updates added. also check for loose or corroded connections at the terminals.

    Aug 27, 2008 | 2003 Chevrolet Blazer

    3 Answers

    Brake light on 2001 chevy blazer LT 2wd


    When my blazer did this they had to replace part of the wiring harness in the steering wheel. It took forever for them to get the parts because we live in nowhereville, but once it was in it works again and no problems. I had to take it to the actual chevy dealer because none of the other places had a clue. good luck.

    Jun 30, 2008 | 2001 Chevrolet Blazer

    Not finding what you are looking for?
    2001 Chevrolet Blazer Logo

    Related Topics:

    37 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...