Question about Cars & Trucks

Open Question

Where can i find the adjustment screw for the butterfly on my nissan sunny b13 carburator

I need to adjust the butterfly on the my b13 carburator

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

3dmaster
  • 183 Answers

SOURCE: Idle problem

Yes you can,

do this with your RPM setting,

you ahve to just set you engine race settings,

try & having funn with your car,

THNX

Posted on May 18, 2008

emissionwiz
  • 75005 Answers

SOURCE: nissan ga15 engine idle adjustment locations

The idle speed is computer controled, it is not adjustable, you most likely have sludge in the throttle valve and the idle speed control air bypass valve, clean them with carb spray with the engine running.

Posted on Sep 17, 2008

  • 15 Answers

SOURCE: want to find idle and mixer,choke adjustment screws

Please indicate the type of engine?

Posted on Aug 06, 2009

  • 1986 Answers

SOURCE: adjusting headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

  • 9 Answers

SOURCE: Nissan B13 sentra isn't starting.

All engines need 3 components: fuel, spark, and oxygen.
You'll need to check all 3 of these. start by checking your spark plugs to see if they aren't gapped or melted. Then check to make sure that fuel is reaching the engine. make sure that the fuel filter isn't clogged.
If you have the tools, run a vacuum pressure test on the lines.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan 1400 consuming too much petrol. How do you adjust air ratio in the carburator


No reference to your model 1400...but if it has a carburetor the air/fuel mixture is set with 2 screws on the front side...to adjust each one...car must be running, turn each screw clockwise until your motor starts to stall...then back out (counter-clockwise 1 1/2 turns from stall...should smooth out as fine tune adjusting...each screw must be re-set this way...could also be dirty or clogged air filter, dirty carb throttle body...and need new spark plugs...probably needs the standard parts tune-up...Hope this helps.

Jun 09, 2015 | Nissan Cars & Trucks

1 Answer

Opel kaddet 1995 model. How do I adjust the


There are only two adjustments on a carburetor, the air mixture setting and the butterfly valve position setting. The air mixture screw is on the side close to the mounting flange, and has a spring behind the screw head to keep it in position.
To adjust it, look for the throttle valve screw which is also on the side, it ix the one that attaches close to where the throttle cable attaches to the carb. Turn the set screw down to let the car idle as slowly as possible. Now go to the air mixture screw. Turn it slowly first in one direction until the revs drop, then turn it out to the point where the revs are maximum. You might have to turn the screw back and forth until you find the best position. Now turn the throttle adjustment back to idle speed.

Aug 28, 2014 | Opel Kadett Cars & Trucks

1 Answer

Stalls when it warms up leave it for 5 minutes then it starts then does it again on a 1987 Volkswagen cabaret


Is it carburated? If it is then adjust the coke until the butterfly is barley closed when cold. This is accomplished by loosening the choke spring cover screws and turning counter clockwise to loosen the spring tension on the butterfly. If the spring is too tight it causes the engine to food and die.

Jul 29, 2014 | Cars & Trucks

1 Answer

Nissan ga13 carburetor diagram


hi i need a ga13 nissan sunny model b13 carpretor kit diagram how and ga13 manual timing,engine,distridutor (manual)and rack power steering manual and staring switch

Jun 16, 2013 | Cars & Trucks

2 Answers

What do I do if My 1981 corvette idles at high rpm (1500) and will not back off.


you may have a vacuam hose off somewhere, else adjust the throttle plate stop on the carb where the linkage comes to rest

Apr 18, 2013 | 1981 Chevrolet Corvette

2 Answers

I just rebuilt my F-150 1 barrel Carter carb (1985)once started runs great under all power ranges.Problem? Hard to start.


should adjust the butterfly to about 3/8" opening at 50 degrees farenheit when engine is cold. Usually about 1 mark to the lean side on the choke spring housing. If unsure set the choke to the center mark than richen up one mark at a time until the engine starts and idles up when cold after properly setting choke by fully depressing and releasing the accelerator before cranking. If it doesn't idle up enough turn up the fast idle screw 1/2 turn at a time. Another common problem with the YFA is the choke heat riser tube rusting off at the manifold and the choke not unloading when the engine warms. Install a new riser tube after using a drill bit the same diameter as the tube to drill out the remainder of the old tube in manifold before inserting the new tube and attaching to choke housing.

Aug 04, 2010 | 1985 Ford F150

1 Answer

Rebuilt carburator and truck runs rich. Cant get adjusted right and under accelereation truck boggs down


im pretty sure that the float adjustment is set wrong, if to high it will act as if truck is flooding out, and be very rich. if to low you will not get the power you need. readjust float level. make sure there is no dirt inside carburator. for adjustment turn screws way in and back out 1 and a half turns.start from there.

Jun 03, 2010 | 1985 Nissan Pickup

3 Answers

Nissan ga15 engine idle adjustment locations


The idle speed is computer controled, it is not adjustable, you most likely have sludge in the throttle valve and the idle speed control air bypass valve, clean them with carb spray with the engine running.

Sep 17, 2008 | 1996 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...