Question about Nissan Cars & Trucks

Open Question

2002 gu patrol 4.2 turbo diesel ac belt diagram

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Saaboheme
  • 76 Answers

SOURCE: 1993 saab 900 belt diagram

Sorry, I don't have access to a Bentley now. There are 4 belts, 2 for alternator etc, 1 for aircon and 1 for pwr steering.
The power steering belt goes round the power steering pump & crank pulley only.
The paired belts go round crank pulley, alternator and water pump.
The aircon belt goes round crank pulley, aircon compressor and tensioner.
Alternator / water pump pair are closest to the engine.
Power steering is in the middle (with aircon) or closest to the bulkhead (without aircon).
Aircon (if fitted) is closest to the bulkhead.

(1) If you do not have an AC compressor, skip this step and go to step 2. If you dohave one, begin by cutting any cable ties that hold the main wiringharness to the AC hoses. Lift the harness up and over onto the camcover until it's near the PCV valve, and is now out of your way.

All nuts & bolts in this step are 13 mm.

Then, slacken the 2 bolts attaching the AC tensioner pulley mount (athick triangular steel plate) to the head. Use a long box wrench (ringspanner, in Englishicon_cheesygrin.gif ).

Using a deep-wall socket (or an offset ratchet wrench, or plain wrench)on the adjuster nut, back it off until there's no more tension in thebelt (you won't be able to remove the belt yet, though).

Now, remove the upper of the 2 mounting bolts and its washer, and pivot the tensioner down; remove the belt.

Remove the lower bolt, and lift out the tensioner. Look the triangularplate over for cracks, and spin the pulley to see if its bearing issmooth and quiet. (If you find problems, the pulley is about $15 and www.eeuroparts.com sells the entiretensioner assembly for something like $70.) Back off the adjuster nutuntil it's about 1/4" (1/2 cm) from the end of its threaded rod (usevise-grips to clamp the rod's other end onto the triangular plate, orput the whole thing in a vise).

(2) Slacken the bolt and nut holding the power steering pump to thehead and to the RH engine mount, respectively. Slacken the adjuster nut(yes, anotherthreaded-rod type thing) by about 1/2" (1 cm). You can use a normalwrench for this, but it takes forever--so I made a special tool bytaking a cheapo 13 mm open-jaw wrench and bending it to a 45-degreeangle just below the jaws (cut it to length if it's too hard tomaneuver). Loosen the mounting nut until it's almost off (but not completely off,or you'll lose the bolt it screws onto--this bolt was designed to fallout when the nut is removed). Pull the nut end of the threaded rodtowards the firewall to get it of the adjuster fork. Push the pumptowards the engine centerline and pull its belt off (you may need topry with a screwdriver to get it out of the pump pulley completely).

(3) Slacken the 16 mm nut on top of the alternator. Back off the alt.adjuster's 10 mm nut about 1/2" (1 cm)--a ratcheting wrench helps here.(This is the last threaded rod--I promise.) Completely remove the 16 mmnut, and pull the adjuster towards the firewall until it's out of thealt.

Now for the clever part: Cut yourself a wedge from a piece of wood (2 x4 is perfect), with a rise of 3" (8 cm) and a run of about 12" (30 cm).Push the alt. towards the engine, and shove the wedge in between theside of the alt. and the coil-spring tower (master cylinder mountingbracket works, too). Keep pushing the alt. and driving the wedge downuntil the alt. is so close to the engine that it's compressing thelower heater hose.

Pull the outer belt off the alt. pulley. Working from the RH side ofthe car, lift the belt off the water pump pulley and then disengage itfrom the crank pulley. Now, pull the inner belt into the outergroove of the water pump pulley. Go back to the LH side of the car, andmove the inner belt into the alt. pulley's outer groove. Try removingit from this pulley; if too difficult, either wedge the alt. closer tothe engine or try pulling the belt off the water pump pulley from theRH side of the car (a helper is very useful for all this).

(4) Install the new inner belt by fitting it into its groove in thecrank pulley first. Work it into the outer grooves of the alt. andwater pump pulleys, then into the inner ones. Install the outerbelt--again, first onto the crank pulley, then the water pump and alt.pulleys.

Remove wedge. Insert tensioner into alt. making sure the threaded rodsettles into its fork, and refit its 16 mm nut--but don't fully tightenit yet. Tighten 10 mm adjuster nut until belts can be pushed in only1/2" (1 cm) by thumb pressure (applied 1/2 way between water pump andcrank pulleys).

(5) Push PS pump as close to engine centerline as possible, andfinger-tighten its mounting bolt to hold it there. Fit a new beltaround the crank pulley first, then work it into the pump pulley groovefrom the bottom of the pulley until it pops in. You may need to use both hands, and/or carefully pry the belt on with a screwdriver.

Loosen the bolt you just tightened. Pull the pump away from enginecenterline, insert threaded rod into its fork (you may have to back theadjuster nut off some more), tighten the mounting nut (but notcompletely), and screw in the adjuster nut until the belt deflects asdescribed in (4) above.

(6) Start the engine. Blip throttle, watching the belts deflect as theengine speed goes up and down. If the "blur" you see midway down eachbelt is over 1" (2 cm) wide, tighten the belt(s) until it isn't. Tighten the PS pump mounting nut and bolt, and the 16mm nut on the alt.

If your car doesn't have AC, your belt replacement is over!

(7) If you haveAC, reattach the tensioner to the head with the lower bolt only (andleave this bolt finger-tight). Fit the new belt around the crankpulley, then around the compressor pulley and, finally, around thetensioner.

Reinstall the top tensioner bolt and its washer. Be careful and patienthere--you're threading a steel bolt into aluminum, so make sure it goesin straight. You may have to back off the tensioner nut a little. Leavethis bolt finger-tight.

Screw in the adjuster nut to get the deflection as described in (4)above. Start the engine, and blip the throttle. Watch belt's "blur" on LHside of engine. Adjust as in (6). Switch on compressor, and repeat.

If satisfied, tighten the 2 tensioner bolts. Return wiring harness toits original position, and re-secure with cable ties if needed.

Posted on Dec 16, 2008

Ad
  • 840 Answers

SOURCE: Need serpentine belt diagram for Dodge Ram 3500 diesel truck

no you should be able to do it There should be a routing label on the underside of hood or on the radiator support/ Its should not be very hard if you have one already just loosen the Alternator it will slide down get the other one ready look to see the way its routed then slide the new one and tighten up the alternator thats it/ Please rate my response thank you very much

Posted on Jan 31, 2009

jingB
  • 19 Answers

SOURCE: wont start when hot!

hello there, wow my dream p-up. nissan pathfinder 4x4,  unfortunately i have to settle with my nissan navara truck. anyways, the possible problems would be the injectors and injection pump. injectors are really direct on the combustion chamber so everytime the engine runs it is severely exposed to very high temperatures. the nozzle tips are the ones very much abused. the injectors have 2 seals. the first one which hugs the body of the injectors which is usually made of hard copper and the 2nd is called the chamber washer which is a stainless steel type concaved washer which serves as the nozzle tip seal and heat nozzle tip heat dispenser. if the nozzle tip floats there is a tendency that the tips are flame red due to heat thus, diesel is boiling to the point of turning to vapors enough to push the remaining fuel back to the injection pump when you shut the engine. then the one way valves of the injection pump comes into play. the valves might be weak and due to the high pressure, fuel slowly creeps back into the pump body. hope this helps.

Posted on Apr 16, 2009

bschilz
  • 2049 Answers

SOURCE: 2006 Dodge diesel belt routing diagram

Here's a link to the diagram you need...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S8023

Posted on Sep 23, 2009

Testimonial: "Awesome! thank you so much for the quick response!"

greg_margo
  • 1959 Answers

SOURCE: belt install diagram 3.4 liter

Below is the diagram you requested. Kindly return to rate this solution and thank you for using Fixya!
Greg
e4ea7d0.jpg

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for fan belt fitment non turbo non AC diesel berlingo 2002 model please


your local citroen dealer should be happy to print this of for you.

Apr 29, 2016 | AC Cars & Trucks

1 Answer

I have a 1999 nissan patrol gu 4.2 st ute and it out heats when i go over 100 km/ hr


Hi Damien, Did you lately have any work carried out to the valve timing assembly? If a timing belt or chain has been replaced and the timing has no been set correctly, misalignment can cause over heating. It would help to know what engine is fitted into your vehicle and if it is diesel or petrol. Regards John

Oct 20, 2013 | Cars & Trucks

1 Answer

Mercedes 1998 C250 Turbo diesel auxiliary belt


try google images there are many variants on this if not tryl and error to refit it

Aug 03, 2013 | Mercedes-Benz Sprinter Cars & Trucks

1 Answer

How to replace a fuel filter on a nissan patrol st turbo diesel 2000


not sure what year model it changed over but it either unscrews from the filter housing(and the water sensor in the bottom of it),or you undo a cover and it is in a canister

May 30, 2012 | 1989 Nissan Patrol Wagon

1 Answer

Timing diagram for nissan zd30ddt diesel engine


I have attached a website on for a 2003 Nissan Patrol Diesel engine as the file is to large to send> it has pictures and directions>Good Luck>> http://ictehe602.blogspot.com/2008/05/my-car-nissan-patrol-grx-30-turbo.html

Mar 23, 2012 | 2005 Nissan Patrol 3.0

1 Answer

IS THERE A RECALL ON BLISTERING DASHBOARDS IN NISSAN PATROL 2006


Hi there:
I suggest called my local Nissan dealer and they did not know anything about it.

Also, you can check out this thread for some experiences of forum members so far with this recall: nissan-patrol-gu-gr-10/gu-series-4-pimpily-dash-52267

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 15, 2012 | Cars & Trucks

1 Answer

IS THERE A RECALL ON BLISTERING DASHBOARDS IN NISSAN PATROL 2006


Just called my local Nissan dealer and they did not know anything about it.

Also, you can check out this thread for some experiences of forum members so far with this recall: nissan-patrol-gu-gr-10/gu-series-4-pimpily-dash-52267

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 15, 2012 | Cars & Trucks

2 Answers

IS THERE A RECALL ON BLISTERING DASHBOARDS IN NISSAN PATROL 2006


Hi there:
I suggest to called my local Nissan dealer and they did not know anything about it.

Also, you can check out this thread for some experiences of forum members so far with this recall: nissan-patrol-gu-gr-10/gu-series-4-pimpily-dash-52267

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 15, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...