Question about Ford Cars & Trucks

1 Answer

I have code po 685 on diesel engine

Code po685 pop up on my 2007 super duty diesel f250 pick up

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 38 Answers

That code is your Auto shutdown relay,on your control circuit.hope this help

Posted on Dec 08, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2000 ford f250 super duty 4x4 7.3L diesel oil leak

The HPOP (high pressure oil pump) is right under the filter housing. There are 2 lines that distribute the oil to the cylinder heads. The o-rings on those fittings go out. Kit is available from Ford or International. You will need a special wrench to get to the fittings though.

Posted on Jun 23, 2008

jmgldsmth
  • 1889 Answers

SOURCE: Fuse panel diagram for 2003 - F250 Super Duty -

I beleive the diagram is on the inside of the plastic fuse cover, mine is.

Posted on Apr 21, 2009

gpgab97
  • 77 Answers

SOURCE: diagnostic code meaning

Low boost. Here's a detailed forum explaining several techniques for trouble shooting.

http://www.powerstroke.org/forum/99-03-7-3-motor-problems/60995-engine-code-p1247.html

Posted on May 03, 2009

  • 299 Answers

SOURCE: 2004 f250 super duty diesel where is low side recharge port ac

on fords ussualy at reciever drier,if not follow large ac line till you find the schrader port.

Posted on Jun 18, 2009

  • 4 Answers

SOURCE: remove and install diesel fuel injector

First, keep everything as clean as possible. Contamination below 30 microns, which cannot be seen by humans, can destory a diesel fuel injection system. Clean everything off anything having to do with connections on the fuel system and cover any connections left open.

Begin by removing the intake manifold. This will remove the clips holding the injection lines passing underneath and around the intake runners. After removing the manifold, cover the openings in the cylinder head (I use wadded-up paper towels).

Next, remove the clips at the brackets on the injection lines closer to the injectors.

Loosen all of the injection connections at the injectors. Do not remove the lines.

You can remove the water crossover tube if it is in your way, but drain about a 1/2 gallon of coolant before your remove the crossover.

Remove the oil fill tube from the timing cover. Turn the engine clockwise, using a 15/16" socket and ratchet (or breaker bar) on the center bolt of the crankshaft. As you turn the engine over, a bolt will show up at the opening where the oil fill tube was removed. Remover the bolt and keep turning the engine over until you have removed all three bolts. Do NOT use the starter to turn the engine over and, after removing the third bolt, do NOT turn the crankshaft any more.

On top of the timing cover, behind the rounded top, is the place where the injection pump is bolted to the cover from the back side. Clean the top of the timing cover where it meets the injection pump and look for a thin line scribed into the cover and one on the injection pump. Note the position of the two lines (they are usually aligned) for reassembly.

Remove the throttle cable assembly from the injection pump. Remove all the wires from the pump and note which connection the big pink wire goes to. The other wires will be green. Remove the return hose at the top of the injection pump.

There are three nuts holding the injection pump to the timing cover and you will need a 15mm socket and/or wrench to remove them. When you do, the injection pump and injection lines can be removed as a unit. Note the position of the driveshaft of the injection pump to set the new one the same way. If you are not going to put things back together right away, cut up a plastic garbage bag and make covers for the injectors. Secure the covers with rubber bands or nylon cable ties to keep dirt out of the injectors.

Carefully transfer the injection lines to the new pump. It is possible to cross them up so pay close attention while moving the lines. Transfer the fuel inlet pipe to the new pump and whatever device is mounted on the passenger side of the old injection pump to the new pump.

Get a new injection pump to timing cover gasket and install it over the timing cover studs. Install the new injection pump after setting the driveshaft to match the holes in the gear inside the timing cover. The pump can only be installed one way since it is indexed to the gear. Reinstall the nuts on the studs and set the timing marks to the same position they were when you removed the old injection pump (the lines on top of the timing cover and the flange of the injection pump). Tighten the mounting nuts. Make sure that all the injection lines line up at their injectors, but do not tighten the connections at the injectors yet.

Put the first bolt back into the gear through the oil fill tube hole. Hand tighten it and then turn the crankshaft clockwise as before to install the remaining two bolts. Then, tighten all the bolts securely and resinstall the oil fill tube. Reinstall the throttle connections on the injection pump.

Install a new piece of 1/4" fuel line from the fuel filter to the injection pump (the old one is usuall brittle since it never gets changed). Remove the covers over the opening in the cylinders heads and reinstall the intake manifold using new gaskets.

Reinstall all the injection line clips that were removed and the coolant crossover tube (if you removed it and don't forget to add coolant to the radiator). Reconnect all the wiring on the injection pump, except for the big pink wire. Install a piece of clear tubing on the top of the injection pump and connect it to the return tee in front of it (where you removed the rubber hose from the old injection pump).

Now comes the fun part: Disconnect the glow plug relay connector (two small wires in a connector) from the middle of the relay. The relay is usually on the driver's fender and close to the battery.

Crank the engine, in short bursts, until you see fuel in the clear tubing on top of the injection pump. When you do, reconnect the big pink wire on the injection pump. Continue to crank the engine in short bursts (allowing the starter to rest between cranking cycles) until you see fuel dripping out of the injection lines at the injectors. When you do, tighten the connections where fuel is dripping. When all lines have been tightened, reconnect the glow plug relay connector. Remove the clear tubing on top of the injection pump and reinstall the fuel line that was removed from that location.

Then, try starting the engine normally. If it will not start, try some WD-40 down the intake. You can use ether, but you MUST disable the glow plugs be removing the connector at the relay.

The engine may run rough or stall at first but it should smooth out after all the remaining air comes out of the system.

Torque values are as follows:

Intake manifold: 25-37 ft-lbs
Gear bolts: 13-20 ft-lbs
Injection pump mounting nuts: 25-37 ft-lbs
Injection lines: 15-24 ft-lbs ("wrench tight" is fine)
Injection pump fuel inlet fitting: 15-20 ft-lbs

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F250 diesel 2001 running then engine stalls after 30 minutes


Ford had a problem with the cam shaft sensor located on passenger side of engine on crank shaft thois will cause the engine to shut down.

Apr 20, 2014 | 2001 Ford F250 Super Duty Super Cab

1 Answer

I need a manuel how to change 6.0disel 2003 fuel injectors


At the auto parts store pick up a copy of Haynes Diesel Engine Repair Manual, part #10330. It covers that and a lot of other things for the DIYer. It costs about $20. Hope this helps.

Mar 19, 2010 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

On a 2000 ford super duty does the cab have to come off to remove cylinder head


No it does not. Your engine should either be the V8, V10 gasser or the 7.3 ltr diesel. All of these engines have timing and gears in the front side of the engine. The only ones that will need the cab removed or pulling the engine is the trucks equipped with the 6.0 liter engine as they have the gearing on the back side of the engine. These started in 2003 and went until 2007 I believe.

Feb 06, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

F250 Diesel engine won't start in cold weather


check your glow plug relay! located on the right side head

Dec 27, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Water in fuel system of a Ford F250 diesel engine.


there is an additive at most auto parts stores and even some gas stations, i forget the name but if you read the bottle it will say something about removing water from the fuel system, they are generally located next to the "octane booster" or "fuel system cleaners"

Aug 09, 2009 | 2001 Ford F250 Super Duty Super Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...