Question about 1996 Oldsmobile Cutlass Ciera

Open Question

Head torque specs 96 cutlass ciera - 1996 Oldsmobile Cutlass Ciera

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: 92 cutlass ciera not starting

Sounds like it could be the fuel pump or injectors.

Posted on Dec 23, 2008

Ad
  • 2 Answers

SOURCE: The windows in the 95 oldsmobile cutlass ciera won't work at all

maybe the wire is severed where the door (drver dr) pivots. thats what was wrong with mine. there is a rubber boot with crinkles in it that hold all the wires together. you can also try replacing the switch board that controls the wndws on the drvr dr. hope that helps.

Posted on Jan 20, 2009

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

Healeyman
  • 1198 Answers

SOURCE: 1994 old cutlass ciera 3100 blown head gasket.

Get a Chilton's book on the car. It will take you thru the whole job, and give you the torque specs for putting it back together. You will need a torque wrench, foot pounds, and a good socket set.

Posted on May 04, 2009

  • 14036 Answers

SOURCE: Changing spark plugs on a 1995 Oldsmobile Cutlass Ciera

ALL YOU NEED IS 3/8 RATCHET WITH A 5/8 SPARK PLUG SOCKET.YOU NEED EXTENSIONS AND UNIVERSAL JOINTS TO GET TO HARD TO REACH PLACES.YOU NEED A SPARK PLUG GAUGE.YOUR SPARK PLUG GAP SETTING WILL BE. 0.060 THAT WILL BE FOR THE 2.2 AND 3.1 ENGINES.

Posted on Aug 17, 2009

Testimonial: "Thank you very much for your advice and time!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caliper torque specs?


Google ,what is the torque specs on (make,year,model front or rear) mounting bolts on the caliper

May 04, 2016 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

Torque specs


Which engine do you have?

May 08, 2013 | 1994 Oldsmobile Cutlass Ciera

1 Answer

1994 cutlass Ciera... I just swapped engines 3.1 from a 96 to a 94...everything went great, except the temperature gage doesn't work. I see in the 94 there is a sending unit on the back head just...


Your 94 engine has separate coolant temp sensor and gauge sender. The 96 engine incorporates both in the engine coolant temp sensor. The coolant temp sensor is near the t-stat, below the throttle body. Check to see how many wires are in this plug. If it only has two, you may be able to use the plug from the 96 motor and wire it into the wire where the original sensor was. You should be able to just color match. Not sure if you can get away with this but the 96 plug should have a third wire, and it's woth a try.

Aug 22, 2011 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Need torque sequence and specs for cylinder heads on a 1988 olds cutlass cierra with a 2.5 liter 4 cylinder engine


WELL ..THE FINAL PASS ON IT IS 65 FT LBS
YOU WANT TO DO THREE PASSES OF EQUAL INCREMENT'S LEADING TO 65 FT LBS
STARTING FROM THE CENTER TWO BOLTS AND WORKING YOUR WAY OUT IN A CROSS
SO BASICALLY THE FIRST PASS WOULD BE 21 FT LB.THE SECOND PASS WOULD BE ROUGHLY 43 LBS THEN THE FINAL PASS OF 65 FT LBS.


Dec 26, 2010 | 1988 Oldsmobile Cutlass Ciera

2 Answers

Need l head bolt for cutlass ciera. l998


Go to your local GM dealer and ask for the head bolt you need. They will supply it for you

May 26, 2009 | 1995 Oldsmobile Cutlass Ciera

1 Answer

1994 old cutlass ciera 3100 blown head gasket.


Get a Chilton's book on the car. It will take you thru the whole job, and give you the torque specs for putting it back together. You will need a torque wrench, foot pounds, and a good socket set.

May 04, 2009 | 1994 Oldsmobile Cutlass Ciera

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Need to replace intake gasket 1989 Oldsmobile Cutlass Ciera


I am doing intake gaskets right now on an expedition and you have to look carefully around and take your time and you will find what is holding you up from taking it out because nowhere in the book does it state you had to take the two bolts out for the thermastat housing on the expedition that I am working on you can also go to auto zone and they can give you a diagram because you will need the torque specs anyways

Dec 07, 2008 | 1989 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1996 Oldsmobile Cutlass Ciera Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...