Question about 1996 Chevrolet Beretta

Open Question

Show me a video of someeone instaling the heater core in a 96 berretta z26

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ZJLimited
  • 17970 Answers

SOURCE: How do I cange the heater core in my 1995 Chevy

Start by removing the panel under the dash on the passenger side. You will need a regular phillips screwdriver and a snubby 2-3" phillips later. Also get a 1/4" socket set. First thing, go under the car and remove the heater hoses from the firewall and twist out the drain spiggot. Then go back inside the car. The heater core sits under the radio. Under the core is a tray used to catch the leaking antifreeze and drain it out the firewall. You need to remove this tray. It has 6-8 screws holding it. Once the screws are out it is tricky removing it with the center console in, but it can be done-twist and bend. Then remove the screws holding the core in place and pull out the heater core. One note on the replacement-got mine from Oreilly's for $20-the two lines coming out of the heater core swivel to line up with the holes through the firewall. If you don't swivel them it will never seem to fit. Then reverse the above order, fill up the fluid, bleed the air off and away you go. Took me about 3 hours total in a parking lot. Ruined a shirt, but got it done. You will also cuss being upside down under the dash. It's a small place for a 240 lb. guy :) This was for a 1993 Beretta. Expect some bloody knuckles and a few mental breakdowns.

Good luck, and rated the help!!!
REMOVAL & INSTALLATION CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

For heater core removal on these vehicles, please refer to the procedure for vehicles with A/C.
1994-96 VEHICLES
See Figures 1, 2 and 3

  1. Properly disable the SIR system, as outlined earlier in this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Raise and safely support the vehicle.
  5. Disconnect the drain tube from the heater case.
  6. Detach the heater hoses from the heater core.
  7. Carefully lower the vehicle.
  8. Remove the right and left sound insulators.
  9. Remove the steering column opening filler.
  10. Remove the floor air outlet duct.
  11. Remove the heater core cover.
  12. Unfasten the heater core mounting clamps, then remove the heater core from the vehicle.
bda4cf8.gif
Fig. 1: The heater core is located in the passenger's side footwell, below the glove compartment

d3686c3.gif
Fig. 2: Exploded view of the heater core and related components (1 of 2) - 1994-96 vehicles

45d1f7c.gif
Fig. 3: Component list for the heater core and related system components (2 of 2) - 1994-96 vehicles

To install:
  1. Position the heater core in the vehicle and secure with the mounting straps.
  2. Install the heater core cover.
  3. Install the floor air outlet duct.
  4. Install the right and left sound insulators.
  5. Install the steering column opening filler.
  6. Raise and safely support the vehicle.
  7. Connect the heater hoses to the heater core.
  8. Attach the drain tube to the heater case.
  9. Carefully lower the vehicle.
  10. Connect the negative battery cable.
  11. Enable the SIR system, as outlined earlier in this section.
  12. Connect the negative battery cable, then start the engine and check for coolant leaks. Check the coolant level, and add if necessary.
WWW.AUTOZONE.COM

Posted on Aug 11, 2009

Testimonial: "Thaks much yor directions helped alot. Thank You. LittleThunder128@comcast.net"

  • 30 Answers

SOURCE: low coolant light on in 1996 chevy berretta

get a scan tool for that car i believe a tech 2 scanner will work adn clear the codes, if it comes back on then you are going to have to do some more digging

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove intake manifold on a 96 Chevrolet Beretta Z26


This is not the kind of job that can be described here. If you do not have a manual, special tools and more importantly the experience I would advise you take time to watch some youtube videos and find a baretta owners forum and get to know the people there.

Mar 16, 2015 | 1996 Chevrolet Beretta

1 Answer

How to replace heater core


Hi Quinton, I'm glad to help!

Quinton, this is a job that's very hard if you've never repaired cars before. The entire dash must be removed to gain access to the heater box that must also be removed to change out the core. You can google: how to replace heater core on 96 Lincoln town car. This will give you video's on how its done and give you an idea of the work involved. Hope this helps and have an awesome day Quinton.

Mar 05, 2014 | 1996 Lincoln Town Car

1 Answer

Where is the heater core on a 96 suzuki truck


truck? the 96 sidekick?
the heater core is behind the glove box
and see here for full extraction
very hard job.
both the FSM pages are linked and a slide show , showing ALL.
http://www.fixkick.com/Cooling-engine/heater-core-madness/shrunk/html/index.html

Apr 12, 2013 | Suzuki Cars & Trucks

2 Answers

How to remove and replace heater gore


Welcome to Fixya

Remove the heater assembly if necessary, the cooling system must be drained before removing the heater core. When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing

  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement. The heater housing is disassembled to get to the heater core.

Heater Core

  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.


Thank you for using Fixya!

May 14, 2011 | 1996 Subaru Impreza

1 Answer

Heat dont work fine suppost to be heater core or cooling sensor i need diagram for the heater core so i can change it


from autozone.com:

1992-96 Models

See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. From under the dash, remove the heater protector from the front of the A/C and heater unit. It is attached by two clips.


jturcotte_299.gif

Fig. Fig. 1: The heater protector is a panel attached to the front of the unit

  1. Unscrew and unclasp the heater core. Disconnect the heater pipes.
jturcotte_300.gif

Fig. Fig. 2: There are three screws holding the pipe clamps

  1. Pull the core out of the vehicle.





jturcotte_301.gif

Fig. Fig. 3: Slide the core out in this direction from the unit


To install:

  1. Place the core into the A/C and heater unit.
  2. Connect the heater pipes.
  3. Install the 3 clamps and screws to secure the unit.
  4. Install the heater protector.

9. Remove radiator cap, start car, refill system, allow car to reach normal temp with thermostat open and coolant flowing in radiator. open any bleed ports on engine to release trapped air. top off radiator and close cap.

Nov 26, 2010 | 1994 Toyota Camry

1 Answer

How to install a heater core?


1994-96 Models
(see Figure)
  1. Use quick disconnect tool T85T-18539-AH to disengage the water hoses from the core, then plug the hoses.
  2. Remove the lower left-hand trim panel by unsnapping it.
  3. Loosen the core cover screws from both sides of the case.
  4. Remove the core and seal.
b5d2fa5.jpg

Fig. : Heater core and cover assembly-1994-96 models


To install:
  1. Install the seal and core.
  2. Install the cover and tighten the retainers.
  3. Install lower trim panel.
  4. Connect the hoses and fill the cooling system.
  5. Fill the cooling system. Disconnect the heater outlet hose at the water pump until coolant begins to escape and this will bleed the system.

Hope this help (remember comment and rated this).

Apr 23, 2010 | 1995 Ford Econoline

1 Answer

Need to replace heater core on 96 tbird....I have Instrument panel out.....glove box out.....center console (climate control unit and stereo) out......have heater hoses disconnected and two mounting nuts...




Section 12-03A: Air Conditioning System—Manual A/C-Heater 1996 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION Heater Core Removal
  1. Partially drain the cooling system.
  1. Remove the tube gasket from the heater core tubes.
  1. Remove four heater core access cover retaining screws, and remove the access cover from the A/C evaporator housing (19850).
  1. Remove A/C electronic door actuator.
  1. Slide heater core (18476) and seals from the A/C evaporator housing (19850).
Installation
  1. Install the heater core (18476) in the A/C evaporator housing (19850) with the tube gasket on the outside of the case.
  1. Install the A/C electronic door actuator as described.
  1. Position the heater core cover on the A/C evaporator housing (19850). Install the four retaining screws.
  1. Refill the cooling system.


    Heater Core





    Item Part Number Description 1 18596 Heater Core Tube Gasket 2 18476 Heater Core 3 18B300 Heater Core Cover 4 390747-S2 Screw (4 Req'd) 5 18N267 Heater Core Cover Seal
  2. 3e541cd.gif

      Feb 16, 2010 | 1996 Ford Thunderbird LX

      1 Answer

      How do I cange the heater core in my 1995 Chevy Berretta


      Start by removing the panel under the dash on the passenger side. You will need a regular phillips screwdriver and a snubby 2-3" phillips later. Also get a 1/4" socket set. First thing, go under the car and remove the heater hoses from the firewall and twist out the drain spiggot. Then go back inside the car. The heater core sits under the radio. Under the core is a tray used to catch the leaking antifreeze and drain it out the firewall. You need to remove this tray. It has 6-8 screws holding it. Once the screws are out it is tricky removing it with the center console in, but it can be done-twist and bend. Then remove the screws holding the core in place and pull out the heater core. One note on the replacement-got mine from Oreilly's for $20-the two lines coming out of the heater core swivel to line up with the holes through the firewall. If you don't swivel them it will never seem to fit. Then reverse the above order, fill up the fluid, bleed the air off and away you go. Took me about 3 hours total in a parking lot. Ruined a shirt, but got it done. You will also cuss being upside down under the dash. It's a small place for a 240 lb. guy :) This was for a 1993 Beretta. Expect some bloody knuckles and a few mental breakdowns.

      Good luck, and rated the help!!!
      REMOVAL & INSTALLATION CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

      For heater core removal on these vehicles, please refer to the procedure for vehicles with A/C.
      1994-96 VEHICLES
      See Figures 1, 2 and 3
      1. Properly disable the SIR system, as outlined earlier in this section.
      2. Disconnect the negative battery cable.
      3. Drain the cooling system into a suitable container.
      4. Raise and safely support the vehicle.
      5. Disconnect the drain tube from the heater case.
      6. Detach the heater hoses from the heater core.
      7. Carefully lower the vehicle.
      8. Remove the right and left sound insulators.
      9. Remove the steering column opening filler.
      10. Remove the floor air outlet duct.
      11. Remove the heater core cover.
      12. Unfasten the heater core mounting clamps, then remove the heater core from the vehicle.
      bda4cf8.gif
      Fig. 1: The heater core is located in the passenger's side footwell, below the glove compartment

      d3686c3.gif
      Fig. 2: Exploded view of the heater core and related components (1 of 2) - 1994-96 vehicles

      45d1f7c.gif
      Fig. 3: Component list for the heater core and related system components (2 of 2) - 1994-96 vehicles

      To install:
      1. Position the heater core in the vehicle and secure with the mounting straps.
      2. Install the heater core cover.
      3. Install the floor air outlet duct.
      4. Install the right and left sound insulators.
      5. Install the steering column opening filler.
      6. Raise and safely support the vehicle.
      7. Connect the heater hoses to the heater core.
      8. Attach the drain tube to the heater case.
      9. Carefully lower the vehicle.
      10. Connect the negative battery cable.
      11. Enable the SIR system, as outlined earlier in this section.
      12. Connect the negative battery cable, then start the engine and check for coolant leaks. Check the coolant level, and add if necessary.
      WWW.AUTOZONE.COM

      Aug 11, 2009 | 1995 Chevrolet Beretta

      1 Answer

      Low coolant light on in 1996 chevy berretta


      get a scan tool for that car i believe a tech 2 scanner will work adn clear the codes, if it comes back on then you are going to have to do some more digging

      Apr 12, 2009 | 1996 Chevrolet Beretta

      Not finding what you are looking for?
      1996 Chevrolet Beretta Logo

      Related Topics:

      121 people viewed this question

      Ask a Question

      Usually answered in minutes!

      Top Chevrolet Experts

      yadayada
      yadayada

      Level 3 Expert

      75807 Answers

      Colin Stickland
      Colin Stickland

      Level 3 Expert

      22133 Answers

      Jeff Turcotte
      Jeff Turcotte

      Level 3 Expert

      8172 Answers

      Are you a Chevrolet Expert? Answer questions, earn points and help others

      Answer questions

      Manuals & User Guides

      Loading...