Question about 1999 Buick Century

Open Question

How to install multifunction switch 1999 buick park avenue

Changing multifunction switch on a 1999 buick park avenue

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
matney68
  • 426 Answers

SOURCE: Cannot change 3 rear spark plugs on 1999 Buick park avenue

there is a special tool for this job but I have cheated on this but you ned to be careful when doing this.The wishbone shaped mount on the front going from motor to front of vehicle, remove and it allows the motor to tilt.

Posted on Jun 19, 2009

Ad
  • 47 Answers

SOURCE: how to remove motor from 1999 buick park avenue

0900c1528004a70e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1 Engine mounting-Vin C engine


0900c1528004a70f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2 Front engine mount assembly-Vins L & 1 engines


0900c1528004a710.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3 Front engine mounting bracket-Vins L & 1 engines

REMOVAL & INSTALLATION


CAUTION When draining coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze, and quite likely to drink any is is left in an uncovered container or puddles on the ground. This will prove fatal in sufficient quantity. Therefore, drain coolant into a sealable container. Coolant should be reused Unless it is contaminated or several years old. The epa warns that prolonged contact with used engine oil may cause a number of skin disorders including cancer. You should make every effort to minimize your exposure to engine oil. Protective gloves should be worn when dealing with engine oil. Wash exposed skin immediately after contact with oil with soap and water, or waterless hand cleaner.
3.8L VIN C Engine

  1. Disconnect the negative battery cable. Using a scribing tool, matchmark the hood hinges and remove the hood.
  2. Label and disconnect the air flow sensor wiring. Depressurize the fuel system.
  3. Remove the air intake duct. Remove the throttle cable and bracket from the throttle body. Place a clean drain pan under the radiator, open the drain **** and drain the cooling system.
  4. Raise and safely support the vehicle.
  5. Remove the exhaust pipe-to-exhaust manifold bolts and separate the exhaust pipe.
  6. Remove the engine mount bolts.
  7. If equipped with a driveline vibration absorber, remove the bolts and disconnect the absorber.
  8. Label and disconnect the electrical connectors from the starter. Remove the starter-to-engine bolts and the starter.
  9. If equipped with air conditioning, remove the compressor mounting bolts and position aside. Do not discharge the system or disconnect the refrigerant lines.
  10. Place a pan under the power steering gear. Disconnect the hydraulic lines and drain the fluid. Use a length of wire to hold the hoses aside.
  11. Remove the lower transaxle-to-engine bolts.

One bolt is situated between the transaxle case and the engine block. It is installed in the opposite direction to the other bolts.
  1. Remove the flywheel cover. Matchmark the flexplate-to-torque converter relationship to insure proper alignment upon installation. Remove the flexplate-to-torque converter bolts.
  2. Remove the engine support bracket-to-transaxle bolts and the bracket. Lower the vehicle.
  3. Attach an engine hoist to the engine lift brackets and support the engine.
  4. Remove the radiator and heater hoses from the engine and position them aside.
  5. Label and disconnect the hoses from the vacuum modulator and canister purge lines.
  6. Label and disconnect the engine electrical wiring harness(es) and position them out of way.
  7. Remove the upper transaxle-to-engine bolts.
  8. Carefully remove the engine from the vehicle.

To install:
  1. Install the engine in the vehicle.
  2. Connect the reposition the engine electrical wiring harness, secure the bracket.
  3. Connect the hoses to the vacuum modulator and the canister purge lines.
  4. Install the radiator and the heater hoses.
  5. Remove the engine hoist. Raise and safely support the vehicle.
  6. Replace the engine support bracket-to-transaxle bolts.
  7. Replace the upper transaxle-to-engine bolts. Install the engine mount bolts and tighten to 70 ft. lbs. (95 Nm).
  8. Install the torque converter and tighten the bolts to 46 ft. lbs. (62 Nm). Replace the flywheel cover.
  9. Install the lower transaxle-to-engine bolts, tighten to 55 ft. lbs. (75 Nm).
  10. Connect the power steering hydraulic lines to the power steering gear.
  11. Install the air conditioning compressor, if equipped.
  12. Install the starter and tighten the mounting bolts to 35 ft. lbs. (47 Nm).
  13. Connect the electrical connections at the starter motor.
  14. Connect the driveline vibration absorber, if equipped.
  15. Install the exhaust pipe and replace the exhaust pipe-to-manifold bolts.
  16. Lower the vehicle.
  17. Connect the air flow sensor wiring. Install the hood assembly.
  18. Connect the negative battery cable. Refill the cooling system.
  19. Start the engine, allow it to reach normal operating temperatures and check for leaks.

Posted on Aug 15, 2009

  • 115 Answers

SOURCE: 2000 Buick Park Avenue Service engine soon light

need to take car somewhere to have the code read with a scanner,try parts stores first some will do it for free if not the dealers have them

Posted on Sep 15, 2009

  • 7353 Answers

SOURCE: 1999 buick park avenue low-beam headlight out

Some of these, the headlight housing comes out, usually 2 thumbscrews that are easily removed to access the housing. Tools usually are not needed,

Posted on Nov 24, 2009

  • 1 Answer

SOURCE: OIl PRESSURE SWITCH

The oil pressure switch is located next to the oil filter

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 park avenue


No lights are most likely the dimmer switch at the light switch, Replace it. rear defrost, could be a broken wire, switch is bad, or the little stands that go across the window, one is broke. No heat, probably the vent motor on the passenger side under the dash, close to the center console.

Jan 13, 2015 | 1999 Buick Park Avenue

1 Answer

Why would my turm signal light stay on even when the car is turned off?


sounds like a hazard switch problem cycle the switch on/off and see
if the light goes off or on we had a problem with the multifunction
switches years ago sounds like your problem

Aug 01, 2014 | 1999 Buick Park Avenue

1 Answer

P1361 code on 1999 buick park avenue


Code 1361 is a problem with the ignition module. The module would need to be tested.

Jul 14, 2014 | 1999 Buick Park Avenue

1 Answer

1999 buick park avenue heated seat stop working


it could be a faulty switch, bad connection under the seat or a burned out element.

Oct 11, 2012 | 1999 Buick Park Avenue

1 Answer

96 park avenue radio removal/installation


http://www.ehow.com/how_5437765_install-radio-buick-park-avenue.html

wiring diagram

http://www.modifiedlife.com/1999-buick-park-avenue-car-stereo-wiring-diagram/



Jul 17, 2009 | 1999 Buick Park Avenue

1 Answer

Cannot change 3 rear spark plugs on 1999 Buick park avenue


there is a special tool for this job but I have cheated on this but you ned to be careful when doing this.The wishbone shaped mount on the front going from motor to front of vehicle, remove and it allows the motor to tilt.

May 23, 2009 | 1999 Buick Park Avenue

1 Answer

1999 buick park avenue change battery now stereo has no display


can anybody give info on what I need to do to get my radio and AC back on since I changed the battery

Apr 14, 2009 | 1999 Buick Park Avenue

Not finding what you are looking for?
1999 Buick Century Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...