Question about Cars & Trucks

Open Question

Central locking wiring diagrams for ldv maxus

I wont to install after markit alarm to my central locking wiring

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 50 Answers

SOURCE: Where is the control module for the central locking.

The alarm module is actually mounted on the drivers side, to the right of the dash fuse block.

Posted on Aug 20, 2008

Ad

SOURCE: central locking

hi there

i had a major problem with my central locking. it would lock with my key but then wouldnt open. the only way i could get in the car was by manually oopeing the driver door but that still meant the the rest of the doors were locked. I managed to buy a relay from ebay and open up my general module . thats the white box thst sits behind uyour fuse box in the glove compartment. it a tricky job as the relays are soldered on and it took approx 30 mins to remove each and replace it.

I have had no problem since

Posted on Nov 06, 2008

desmondsheri
  • 7 Answers

SOURCE: fitting a portman car alarm

We really sorry about your problem.............this has been a problem for many people to solve.........I am here unbehalf of my company ( Solution Technology/Engineer Company United Kingdom).

Before we can solve your problem you need to pay a deposite amount of 100Pounds Sterling, then we send how u can solve the problem after this problem is solve, the remaining amount (100pound Sterling) will be paid to our office.

Please if u agree with the above contact us with the following information:

Sincerely,

Consultant Officer Tel: +44705714853
Desond Sherif E-mail:desmondsherif@rocketmail.com
Solution Technology/Engineer Company,
United Kingdom.

Posted on Nov 09, 2008

  • 45 Answers

SOURCE: Car alarm not activating central locking

It means that the remote is not passing the signal to the car . The alarm has triggered because the system has detected an illegal entry. Replace the remote batteries

Posted on Jan 07, 2009

junmag
  • 175 Answers

SOURCE: Car alarm installed. Car wont start.

im sure you cut the starter wire in the ignition switch. usually white. put it back and check. if it starts check the programming configuration of the black widow

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help needed have a Ldv Maxus, put a new plastic grommet into clutch pedal today as the old one broke, now having trouble getting it into gear unless I pump the pedal Any Idears please.


Sounds like there is now air in the system. If there is a bleed nipple on the slave cylinder, bleed the clutch with new fluid. If not, it is a sealed system and both the master and slave must be replaced as a pair and ensure you follow the instructions otherwise you will get air in the system again.

Jun 01, 2017 | Cars & Trucks

1 Answer

Hello if i change the esa on ldv maxus do i need to re programme the fob remote


Not heard of ESA. But if it is the main part of central locking, yes, FOB's have to be programmed to it.

Jun 16, 2016 | Cars & Trucks

1 Answer

2 way wire diagram


as cars run DC power the polarity doesn't matter in a solenoid unit such as door lock if it has 2 wires ( power wire and earth wire ) Just reverse the wiring and it should work

Apr 12, 2014 | 2012 Subaru Legacy 2.5i Sedan 2.5L 4-cyl....

1 Answer

How to fix 5th gear on my ldv maxus


Its likely you have a problem with the clutchnot completly disengageing or problems with disk or pressure plate

Jun 13, 2013 | 1997 Chevrolet Cargo Van

2 Answers

LDV Maxus 3.5 Drivers door lock initially wouldn't unlock with fob, will work with key. Now will not lock or unlock on fob. Back door will unlock with fob, but does not lock, it has to be locked


The problem is not the actuators, the fault lies in the central locking control unit under the dashboard, behind the glovebox, on the firewall. The CLCU is mounted with the connection terminals to the top resulting in condensation going onto the printed circuit board inside, if the damage started a while ago there is only 3 ways to go.

1. specialist firm to repair the CLCU.
2. Replace.
3. (As I did) buy a cheap remote control receiver with keyfob/s. Cut all wires off the multiplug, there are four pairs, a permanent live and permanent earth. Test each wire to earth on the van to identify the permanent earth FIRST. Then test pairs of wires across 12v/Earth noting which pairs actuate which lock.Isolate in pairs noting which wire has to be live to lock, (Reversed it will unlock) wire each pair into the relay on the remote receiver using the relay to changeover the polarity to each pair You will then be able to Lock/Unlock all the doors, throw the old CLCU away and mount the RCReceiver eslewhere to keep it dry. each door individually. I bought a 2 way RCReceiver and can lock/Unlock front doors seperate the the rear ones which is of far more use! Any decent electrician will tell you how to wire the relays. Job Done..... (100% Sure)

603d3609-f326-41be-a38e-a00bb8d6bdab.jpg

Feb 02, 2013 | Cars & Trucks

2 Answers

Help!!! how to reset a LDV Maxus key fob?


Hi
I know from experience that you cannot really re synch these fobs on the LDV Maxus vans.
What actually is the fault is an onboard component on the pcb has failed and we normally just replace that with a new one..the fob will be tested for operation and sent back. OR its the Relay in the ESA unit - under the left hand front glovebox on the bulkhead - black with cables going into it. We have those relays (soldered to the pcb) we can supply those or do the work for you. The fob connects to that ESA and the unit then fires the relays to open/close the doors. Sometimes that unit is installed upside down which causes water (condensation) to enter the box and have fun with your electrics.
The fob is SYNCHED to this unit via coding we can use your old fob to clone to a new fob and that will work with the ESA and the vehicle.
We have the parts on this link Items for sale from remobilise ltd

Here is a link to how to program the fob to the vehicle via the programmer - NOTE how you MUST have a working fob to program another (text at the start of the video... LDV Maxus flv

We can fix most problems on the LDV Maxus that occur with faults to do with the Central locking/fobs/ESA/ETACS - three relays are in the ESA and they control ONLY the central locking - two more relays are in the ETACS unit (behind the ashtray) and they control the fogs and intermittant wipers.

Any help or info needed please contact info@remobilise.co.uk
or tel 01792 896404.

We are based in Swansea UK.

Aug 30, 2012 | Cars & Trucks

1 Answer

Ldv maxus wont start off key but goes with a push everytime


You could check your battery if its properly charged then check your alternator, probably d alternator is bad and doesnt charge the battery wel enough. So its either your alternator or ur battery. Also try removing a batt terminal after each drive to avoid draining

Jan 29, 2012 | Cars & Trucks

2 Answers

Central locking broke on ford focus c max 2004


Fuse No 64 on back of fuse box inside cabin behind glove compartment undo two bolt and turn fuse board around pull the wires gently apart to see fuse 20 amp

Nov 07, 2008 | 2004 Ford Focus

3 Answers

Cow boy alarm fitter came to fit alarm.When came to pick car up cenral locking did not work. he didnt no what he had done. So i had my car back with out paying 3 days later . I have now taken alarm of...


Try to check wires to the driverside central lock master motor. alarm installer probaly cut wires inorder to link the alarm to your cars central locking system.

Central lock master motor usually comes with 5 wires, two is the motor supply wire capable of reversing its polarity depending on lock or unlock request, the remaining 3 is just a swtich. One is ground and the two are negative request swtich for lock and unlock. If all fuses were good this moght be the problem, try also to check the outside fuses- in the hood. Good luck!

Aug 25, 2008 | Mitsubishi Lancer Evolution Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...