Question about Honda Accord

Open Question

Honda pilot 2004 baro sensor location - Accord Honda Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 78 Answers

SOURCE: replacing headlamp of a 2004 Honda Pilot

i believe it is held in by a spring underneath the rubber boot the spring swings over like a door and hooks in a notch

Posted on Nov 15, 2008

SOURCE: Knock Sensor installation for 2003 Honda Pilot

I don't know where the knock sensor is exactly on this engine, but if you buy the replacement first it will help you identify it.

It's screwed into the block near the head or the head itself. It has an electrical connector attached to it (two wires, I believe).

The replacement is pretty simple: remove the electrical connector from the old one; screw it out with a wrench; screw the new one in and; plug the connector onto it.

Charlie

Posted on Aug 22, 2009

arauzvictor1
  • 466 Answers

SOURCE: location of ecm on 2004 honda pilot.

The PCM is located in the center of the board in the bottom

Posted on Jun 23, 2010

  • 356 Answers

SOURCE: Honda Odyssey 1996, a problem:

Take it to Honda.

Posted on Feb 12, 2011

rfoulds85
  • 128 Answers

SOURCE: where are sensors located? Got codes

The map sensor is mounted in the tube going fromt he air filter to the throttle body

Posted on May 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

V6. What are the probable causes of DTC P0108?


code p 0108 refers to manifold absolute pressure (MAP) sensor/ barometric pressure(BARO) sensor---high input===causes ---wiring short to positive ---MAP sensor---BARO sensor---ECM
Check /replace the sensors

Jan 09, 2016 | 2004 Lincoln LS

1 Answer

Mapping codes P0107, P2263 & P2227 come up on scan tool what are these codes relating too? Ford Ranger 2008 not 2004 3.0 4 door


code p 0107 refers to manifold absolute pressure (MAP) sensor /barometric pressure (BARO) sensor --low input ====causes --wiring short to ground ---MAP sensor ---BARO sensor ---ECM
code p 2263 refers to turbo charger (TC) boost pressure /supercharger (SC) boost pressure ---performance problem====causes --mechanical fault
code p 2227 refers to BARO sensor -range / performance problem===causes wiring --- BARO sensor --- ECM
I would be testing the BARO sensor for a problem as it is listed for all 3 codes
if you don't have such a sensor you have a MAP sensor which is reading in the same area so test that as well

Oct 19, 2015 | 2004 Ford Ranger

1 Answer

What is a code po106 on a 2004 lincoln ls


code p0106 refers to manifold absolute pressure (MAP) sensor /barometric pressure (BARO) sensor ---range /performance problem===causes --intake /exhaust leak--wiring--MAP sensor ---Baro sensor.

check for vacuum / air leaks and /or change sensors.

Aug 17, 2014 | 2004 Lincoln LS

1 Answer

2004 honda pilot drive light blinking


Check for error codes as this can be related to fault in the transmission , failure of the sensors or a possible ECU error.

Dec 30, 2011 | 2004 Honda Pilot

2 Answers

Location of ecm on 2004 honda pilot.


The PCM is located in the center of the board in the bottom

Jun 22, 2010 | 2004 Honda Pilot

1 Answer

WHERE IS THE THERMOSTAT LOCATED IN 2001 HONDA PILOT


Honda didn't make the Pilot until 2003. Check th year. On the 2003 model you can find it on the driver's side of the engine where the lower radiator hose connects at the engine. Hope this helps,...ZMANRACING

Dec 05, 2009 | 2004 Honda Pilot

1 Answer

2004 Honda pilot transmission 4 x 4


the honda pilots are all whee drive so there is nothing to lock in the trans mission does it on it's own. it uses sensors on the wheel to tell it when and whitch tire to put the power to.

Nov 12, 2009 | 2004 Honda Pilot

1 Answer

Bank 1 show on my ob11 tester


check the camshaft position sensor wiring located near the left front corner of the black cover over the top of the engine, my wiring was worn in half and caused my pilot to not start

Jul 31, 2008 | 2004 Honda Pilot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...