Question about 1995 Nissan Maxima

1 Answer

How to set the timing chain

I am replacing the water pump of my 1995 3.0 v6 infinity (same as altima) but my son removed the chain with out marking it, now I need to set the timing. How do I do this? There's marking on the valve sprockets and on the chain. Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Line the marks on the chain to the sprokets and it should be ok, is that what we call a qx, a32 chassis seires?

Posted on Jan 15, 2009

1 Suggested Answer

  • 8 Answers

SOURCE: I am replacing the water

This should be the same engine as the Maxima. If that is the case, there is no reason to remove timing chain or get it out of time. The pump is driven by the timing chain, but is not "in time".

The pump is under its own cover. The chain tensioner is under its own cover. The pump is removed after the tension is released on the chain, the tensioner pinned in its retracted position to take tension off chain, and the crank is rotated about 20 degrees counter clockwise to slacken the chain at the pump sprocket without coming off the cam sprockets. Then, the pump is remove by removing its mounting bolts and then screwing in three long M8 bolts as jack bolts into 3 holes (carefully and evenly) to jack out pump. The pump is sealed from the engine case by two o-rings that must be replaced. I think the pump mount bolts are sealed with silicone when replaced. I would get a Haynes or other reliable manual.

If you truly have to reset or check timing, definitely get a book.

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove the timing chains and gears


Everything blocking the timing chain cover needs to be removed. THEN REMOVE COVER AND REMOVE OLD CHAIN making sure your cam and crank marks align. install new chain

Mar 13, 2015 | 2003 Nissan Altima

1 Answer

Do you have step by step instruction on how to replace a water pump on a 2002 Chrysler Sebring convertible?


REMOVAL - 2.7L

NOTE: It is normal for the water pump to weep a small amount of coolant from the weep hole (black stain at weep passage). Do not replace the water pump if this condition exists. Replace the water pump if a heavy deposit or a steady flow of engine coolant is evident on side of the cylinder block from the weep hole passage (shaft seal failure). Be sure to perform a thorough analysis before replacing water pump.

WARNING: DO NOT REMOVE PRESSURE CAP WITH THE SYSTEM HOT AND PRESSURIZED. SERIOUS BURNS FROM COOLANT CAN RESULT.

Disconnect negative battery cable.
Drain cooling system (Refer to 7 - COOLING/ENGINE - STANDARD PROCEDURE).

NOTE: The water pump is driven by the primary timing chain.
Remove the timing chain cover, timing chain, and all chain guides


Remove upper intake manifold. (Refer to 9 - ENGINE/MANIFOLDS/INTAKE MANIFOLD - REMOVAL)
Remove cylinder head covers, crankshaft vibration damper, and timing chain cover. (Refer to 9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD COVER(S) - REMOVAL) (Refer to 9 - ENGINE/ENGINE BLOCK/VIBRATION DAMPER - REMOVAL) (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT / CHAIN COVER(S) - REMOVAL)

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
Align crankshaft sprocket timing mark to mark on oil pump housing (TIMING MARK ALIGNMENT). The mark on oil pump housing is 60 degrees ATDC of #1 cylinder.

CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
Remove power steering pump and bracket as an assembly. Do not disconnect power steering lines from pump. Reposition pump and support with suitable retaining strap.
Remove primary timing chain tensioner retainer cap and tensioner from right cylinder head (PRIMARY TIMING CHAIN TENSIONER).
Disconnect and remove camshaft position sensor from left cylinder head (TIMING DRIVE SYSTEM - PRIMARY).
Remove timing chain guide access plugs from cylinder heads (TIMING DRIVE SYSTEM - PRIMARY).

NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (if equipped) and sprocket (TIMING DRIVE SYSTEM - PRIMARY).
Remove left side camshaft sprocket attaching bolts and remove sprocket (TIMING DRIVE SYSTEM - PRIMARY).
Remove lower chain guide and tensioner arm (TIMING DRIVE SYSTEM - PRIMARY).
Remove the primary timing chain.

2_16_2012_2_52_11_pm.gif

Zoom Image link HERE


2_16_2012_2_53_05_pm.gif

Remove bolts attaching water pump to block (WATER PUMP - 2.7L).
Remove water pump and gasket.

2_16_2012_2_53_39_pm.gif
This is the proceedure from the chrysler shop manual if you have any problems let me know. Do yourself a favor and avoid potential bent valves!!!

REPLACE THE PRIMARY CHAIN TENSIONER ASSEMBLY, DON'T WASTE YOUR TIME ATTEMPTING TO RESET IT, IT DOESN'T ALWAYS WORK.

2_16_2012_2_54_27_pm.gif

Zoom Image link HERE

2_16_2012_2_55_10_pm.gif


2_16_2012_2_55_30_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 16, 2012 | 2002 Chrysler Sebring

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

1 Answer

I30 1996 INFINITY WATER PUMP LOCATION


Hi, you have to remove the timing chain cover and then remove the timing chains to get to the water pump which is located beneath it.

Take care

Aug 11, 2010 | Infiniti I35 Cars & Trucks

1 Answer

2002 Intrepid: need to replace the water pump...


In the 2.7L V6, the water pump is driven by the timing chain. I'm pretty sure that in the 3.2/3.5L V6, it's driven by the timing belt. In both cases, it's a lot of work to get to, as you have to remove everything on the top (intake plenum, valve covers) and front (belts, pulleys, idlers, p/s pump, and timing cover) of the engine. Then, after removing and replacing the water pump and timing chain/belt, you have to make sure that the valve timing is exactly right, and reset the chain tensioner on the 2.7L.

A lot of work. Unless you're very comfortable with working on engines, leave it to a professional. You'll save yourself a headache (not to mention some busted knuckles). ;-)

May 17, 2010 | 2002 Dodge Intrepid

1 Answer

How do i get to the water pump on a 1998 nissan altima


THE 2.4L AND 2.5L ENGINES.YOU HAVE TO SAFELY RAISE VECHICLE SUPPORT IT USING JACK STANDS.YOU HAVE TO REMOVE THE RIGHT HAND SPLASH SHIELD.THEN LOOSEN WATER PUMP PULLEY BOLTS LEAVE DRIVE BELT IN PLACE TO KEEP WATER PULLEY FROM TURNING WHILE LOOSEN PULLEY BOLTS.THEN YOU HAVE TO MOVE AC COMPRESSOR DONT DISCONNECT ANY REFRIGERANT LINES.JUST SET IT ASIDE THE ALTERNATOR AND ITS MOUNT ALSO HAS TO MOVED.THEN YOU ARE AT WATER PUMP.NOW THE 3.5L ENGINE WATER PUMP IS IN A TOUGH SPOT.YOU HAVE TO REMOVE ENGINE SPLASH SHIELD.REMOVE THE SUBFRAME BRACKET FROM THE RIGHT SIDE OF THE SUBFRAME ASSEMBLY. REMOVE THE INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM FROM THE ENGINE COMPARTMENT.REMOVE THE IPDMER UPPER COVER AND HARNESS COVER RELEASE THE TWO CLIPS.DISCONNECT THE ELECTRICAL CONNECTORS AND LIFT THE ASSEMBLY FROM THE CASE.REMOVE THE RADIATOR SHROUDS REMOVE THE DRIVE BELTS.REMOVE THE ENGINE COOLING FAN.REMOVE THE RADIATOR AND THE COOLANT RESERVOIR.REMOVE THE IDLER PULLEY AND THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS.REMOVE THE FRONT ENGINE MOUNT.REMOVE COOLANT DRAIN PLUG FROM THE WATER PUMP SIDE OF THE ENGINE BLOCK.REMOVE CHAIN TENSIONER COVER AND THE WATER PUMP COVER FROM THE ENGINE FRONT COVER.REMOVE THE CHAIN TENSIONER.PULL THE LEVER DOWN TO RELEASE THE PLUNGER STOPPER TAB.INSERT A STOPPER PIN INTO THE TENSIONER BODY HOLE TO RETAIN THE LEVER IN THE RELEASED.NO CHAIN TENSION POSITION.MOVE THE PLUNGER INTO THE TENSIONER BY PRESSING THE CHAIN GUIDE AND PUSHING WITH A SCREWDRIVER.MAKE A GAP BETWEEN THE WATER PUMP GEAR AND THE TIMING CHAIN BY ROTATING THE CRANKSHAFT PULLEY 20 DEGREES COUNTERCLOCKWISE.REMOVE THE THREE WATER PUMP MOUNTING BOLTS.INSTALL 2 BOLTS SIZE M8 1.25 X 50 MM INTO THE WATER PUMP BOLT HOLES AND TIGHTEN THEM EQUALLY UNTIL THEY BOTTOM AGAINST THE CHAIN COVER.IT WILL BE NECESSARY TO ROTATE THE WATER PUMP SLIGHTLY TO ALLOW THE BOLTS TO DRIVE AGAINST THE REAR TIMING CHAIN CASE COVER INSTEAD OF THE BOLT HOLES.REMOVE THE WATER PUMP.CLEAN THE SEALANT FROM THE MATING SURFACE AND REPLACE THE O-RINGS.INSTALL THE OUTER O-RING WITH THE WHITE PAINT MARK FACING THE FRONT OF THE ENGINE AND THE INNER O-RING BLACK NEXT.APPLY A LIGHT AMOUNT OF OIL TO THE O-RINGS.TIGHTEN THE WATER PUMP BOLTS TO 62 - 89 INCH POUNDS.TIGHTEN WATER PUMP BOLTS EVENLY DONT OVER TIGHT OR YOU WILL DAMAGE WATER PUMP AND HAVE LEAKS.REINSTALL THE POWER STEERING AND ALTERNATOR ADJUSTMENT BRACKETS AND ANY OTHER COMPONENTS REMOVED FOR ACCESS TO THE WATER PUMP.REFILL THE COOLING SYSTEM.RUN THE ENGINE AND CHECK FOR LEAKS.YOU NEED TO BUY THE HAYNES REPAIR MANUAL.SO THE PHOTOS WILL HELP YOU WHEN REMOVING AND INSTALLING WATER PUMP.

Nov 14, 2009 | Nissan Altima Cars & Trucks

1 Answer

Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/

e09cf57.gif

Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301) .
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
  1. Remove the main wiring harness from the upper engine front cover (6019) .
  1. Remove the eight upper engine front cover bolts and the upper engine front cover .
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
  1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501) .
  1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover .
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
  3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
  4. Loosen the timing chain/belt tensioner nut.
  5. Remove the timing chain/belt .

  6. Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





Sep 20, 2009 | 1998 Nissan Quest

1 Answer

Do I need to remove the timing chain in order to replace the water pump in a 97 Infinity J30?


rubber timing belt will need removed in order to service the pump on that vehicle

Mar 07, 2009 | 1997 Infiniti.5 J30

1 Answer

I am replacing the water pump of my 1995 3.0 v6 infinity (same as altima) but my son removed the chain with out marking it, now I need to set the timing. How do I do this? There's marking on the valve...


This should be the same engine as the Maxima. If that is the case, there is no reason to remove timing chain or get it out of time. The pump is driven by the timing chain, but is not "in time".

The pump is under its own cover. The chain tensioner is under its own cover. The pump is removed after the tension is released on the chain, the tensioner pinned in its retracted position to take tension off chain, and the crank is rotated about 20 degrees counter clockwise to slacken the chain at the pump sprocket without coming off the cam sprockets. Then, the pump is remove by removing its mounting bolts and then screwing in three long M8 bolts as jack bolts into 3 holes (carefully and evenly) to jack out pump. The pump is sealed from the engine case by two o-rings that must be replaced. I think the pump mount bolts are sealed with silicone when replaced. I would get a Haynes or other reliable manual.

If you truly have to reset or check timing, definitely get a book.

Jan 12, 2009 | 1995 Nissan Maxima

2 Answers

Timing chain


A timing belt will no blow up the engine, however it will on occasion bend the valves, you will need to replace the belt and test for damage to the engine. Change the water pump and check all the pulleys while you are in there.

Aug 07, 2008 | 1995 Nissan Altima

Not finding what you are looking for?
1995 Nissan Maxima Logo

624 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...