Question about 1988 Mazda B2200

Open Question

1986 mazda b2000 distributor chaniging rotor - 1988 Mazda B2200

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: Does a Mazda B2000 1986 have a IAT sensor? If so

I say no IAT sensor, but if there was one it would be on intake air ducting coming into carburetor.

Posted on Aug 05, 2009

Ad
  • 138 Answers

SOURCE: my 87 mazda b2000 keeps loosong power when im

The only way that oil would get into the distributor is if the o-ring at the base of the distributor is damaged. To check this, do the following.

Remove the distributor cap. You will see the distributor rotor inside. With a sharpie, make a mark on the outside of the distributor in relation to where the rotor is pointing. (This is important so that your truck is still in time when you reinstall the distributor)
Remove the bolt holding down the distributor. It is commonly a 1/2" or 13mm bolt. Pull the distributor. At the base, you will see an O-ring in a groove at the bottom of the shaft just above the drive gear. If you don't see this O-ring, or it is damaged, that is your problem with oil in the distributor.

When installing the distributor, make sure your mark on the distributor housing is in line with your rotor. Clean and reinstall your dist. cap.

Posted on Jan 01, 2010

  • 1 Answer

SOURCE: i need a vacuum diagram for a 1984 mazda b2000

I have the same problem. I was told that there are 5 or 6 vacuum line diagrams for the same truck. I called the Mazda dealer and they told me for $$$ per hr they would fix it for me. It was not worth there time to research something that old. I took that to mean that it is not on a dvd. Most likely a book , old shop manual. I have asked several people who own Mazda B2000 and most have replied that they removed most of the lines. And got it to run and forgot about it. I know this is not what you want to hear. But after a yr or so of looking that is what I have found.

Posted on Feb 01, 2010

BCAS1298
  • 3092 Answers

SOURCE: how to replace a timing belt on 1986 mazda b2000

Remove timing belt cover, hope this helps on how to align the cam and crank gear's.

51c376b.gif

Posted on Aug 18, 2010

johnjohn2
  • 5763 Answers

SOURCE: i hav a 1986 mazda

the valve clearance for a 1986 mazda B2000 is, Intake and exhaust valves are .012 inches (.30mm).... Hope this is helpful, have a good day

Posted on Mar 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is this little cylinoid? attached to my mazda b2000 truck


Probably the relay to make ur regulator come off and on to charge ur battery?

May 20, 2014 | Cars & Trucks

1 Answer

1986 mazda b2000


nothing . have a compression test done on the engine to determine the condition. have n exhaust test done to get the exhaust emissions reading to determine where the faults lay . Check the condition of the charcoal canister.

Dec 31, 2013 | Cars & Trucks

1 Answer

My 1986 mazda b2000 keeps blowing the parking light fuse


Need to check the bulb's connection,might be corroded or the wire is shorted and touching somewhere

Oct 15, 2013 | Mazda Cars & Trucks

1 Answer

I hav a 1986 mazda B2000, what is the valve clearance pls?


the valve clearance for a 1986 mazda B2000 is, Intake and exhaust valves are .012 inches (.30mm).... Hope this is helpful, have a good day

Mar 18, 2011 | Mazda B2200 Cars & Trucks

1 Answer

Where does the vacuum advance go on a 84 mazda b2000


It goes between the distributor and the base of the carburetor , while your at it give the pipe from the distributor a good **** and make sure the the plate that the points are on moves , ive had to replace a few of those distributors because the diaphragm has gone inside the advance unit .

Jan 04, 2011 | 1984 Mazda B-Series

2 Answers

How to replace a timing belt on 1986 mazda b2000


Remove timing belt cover, hope this helps on how to align the cam and crank gear's.

51c376b.gif

Aug 18, 2010 | 1986 Mazda B-Series

1 Answer

Spark plug firing order for 87 Mazda B2000 pickup


Firing order 1-3-4-2

Distributor rotor turn's clockwise

Jun 28, 2010 | 1994 Mazda 2WD B Series Pickup

1 Answer

My 87 mazda b2000 keeps loosong power when im driving at 75 to 80 miles in 4th n 5th gear i realize oil is getting in distributer rotors n cap could this be the problem n how do i fix it


The only way that oil would get into the distributor is if the o-ring at the base of the distributor is damaged. To check this, do the following.

Remove the distributor cap. You will see the distributor rotor inside. With a sharpie, make a mark on the outside of the distributor in relation to where the rotor is pointing. (This is important so that your truck is still in time when you reinstall the distributor)
Remove the bolt holding down the distributor. It is commonly a 1/2" or 13mm bolt. Pull the distributor. At the base, you will see an O-ring in a groove at the bottom of the shaft just above the drive gear. If you don't see this O-ring, or it is damaged, that is your problem with oil in the distributor.

When installing the distributor, make sure your mark on the distributor housing is in line with your rotor. Clean and reinstall your dist. cap.

Jan 01, 2010 | 1988 Mazda B2200

1 Answer

Does a Mazda B2000 1986 have a IAT sensor? If so where is it located? I have a performance chip I want to tie in.


I say no IAT sensor, but if there was one it would be on intake air ducting coming into carburetor.

Aug 04, 2009 | 1986 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...