Question about Cars & Trucks

Open Question

Got silenced on pimd how do I get un silenced

Posted by Anonymous on


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can I use Yezdi 350 silencer for Yezdi Classic D 250

If it fits then why not. Silencers are only used to even out the power pulses in the exhaust and they do this by a bit of back pressure or padding in the construction of the silencer.

Dec 10, 2014 | Cars & Trucks

1 Answer

I got silence for no reason I try to talk silenced permantely like wtf so can u guys unsilence me pimd

Don't get your point

This is not a business that gives out free info

It is a social web site

Everyone is at home & uses as you do

It is a world wide free chat room only

Hundreds of questions a day go unanswered

Nov 25, 2012 | Cars & Trucks

2 Answers

Engine light came on wit lack of power spluttering and wgite smoke from exhaust

Dear Sir,
As you said engine light is on and misfire with white smoke, it clearly symptom of poor ignition spark may cause of any wire got disconnected or spark plug faulty.
white smoke comes only in case no spark at spark plug and un burn fuel throwing from silencer. check wire and spark plug if any issue let me know. thanks.


Nov 17, 2010 | Hyundai Tucson Cars & Trucks

1 Answer

How do I remove the blower motor on a 2005 dodge magnum

From CAUTION On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death.
  1. Disconnect and isolate the negative battery cable.
  2. Remove the instrument panel silencer from the passenger side of the instrument panel, as follows:
    1. Remove the two push-pins that secure the instrument panel silencer to the instrument panel.
    2. Pull the instrument panel silencer rearward to disengage it from the brackets located near the dash panel.
    c. Remove the instrument panel silencer from the vehicle.
ce992e6.gif Fig. Instrument panel silencer (2), push pins (3) and brackets (1)

3. Disengage the wire harness connector locking tab and disconnect the wire harness connector and wire harness retainers from the blower motor.

4. Remove the four screws that secure the blower motor to the HVAC housing.

5. Remove the blower motor from the HVAC housing.
b21a285.gif Fig. Blower motor (2), harness connector (1), retaining screws (3) and HVAC housing (4)

To install

  1. Position the blower motor into the HVAC housing.
  2. Install the four screws that secure the blower motor to the HVAC housing. Tighten the screws to 20 inch lbs. (2.2 Nm).
  3. Attach the wire harness connector to the blower motor and engage the wire harness connector locking tab.
  4. Install the HVAC wire harness retainers onto the blower motor.
  5. Install the instrument panel silencer onto the passenger side of the instrument panel, as follows:
    1. Position the instrument panel silencer into the vehicle.
    2. Install the instrument panel silencer above the brackets located near the dash panel.
    3. Install the two push-pins that secure the instrument panel silencer to the instrument panel.

  6. Reconnect the negative battery cable.

Sep 21, 2010 | 2005 Dodge Magnum

1 Answer

I am trying to figure out if i have a silencer ring on my turbo in my truck

Hi ,

It is easy to figure out silencer ring

A silencer ring is a metal baffle placed into the turbocharger inlet to reduce whistle from the turbocharger. It is installed in Ram truck engines at the request of Chrysler. The silencer ring has no effect on engine output, EGT, or boost levels. It does significantly reduce high frequency turbo whistle

On Removal: Remove the flex hose from the front of the turbo that goes to the breather. Just inside the turbo, you will see a snap ring that looks like a piston ring(charcoal color), very gently with a small flat blade screw driver, lift one end of the snap ring out of the groove, then continue to work around the snap ring, lifting it out of the groove. When the snap ring has been removed, you can easily remove the silence ring. You may want to keep the snap ring and silencer together in a plastic bag in case you get tired of the extra whistle.

With Ring
silencer-t.jpg silencer-no-t.jpg Turbo
Without ring

Sep 23, 2009 | 1996 Chevrolet C/K 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides