Question about 1999 Mercury Cougar

Open Question

How do you change 99 cougar head gasket - 1999 Mercury Cougar

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: canyou chage head gaskets on 99 ford cougar 2.5 v6

Yes! No need for the engine to come out at all. But there is going to be alot of parts coming out, you will need a manual from aoutozone or advance $14.99 It will tell you step by step.

Posted on Jun 21, 2009

Ad
  • 60 Answers

SOURCE: i need a print out

Removal

  1. Drain engine cooling system.
  1. Disconnect battery ground cable (14301) .
  1. Remove engine air cleaner (ACL) (9600) including air cleaner outlet tube (9B659) .
  1. Loosen drive belt tensioner (6B209). Remove drive belts (8620) .
  1. If LH cylinder head (6049) is being removed, perform the following:
    1. Remove oil filler cap (6766) .
    1. Remove power steering pump front mounting bracket retaining bolts.
    1. Remove generator (GEN) (10346) and belt idler pulley (8678).
    1. Remove power steering pump/generator bracket retaining bolts. Leave hoses connected, place pump/bracket assembly aside in a position to prevent fluid from leaking out.
  1. If RH cylinder head is being removed, perform the following:
    1. Remove drive belts .
    1. If equipped with A/C, remove mounting bracket retaining bolts. Leave hoses connected and position A/C compressor (19703) aside.
    1. Remove positive crankcase ventilation valve (PCV valve) (6A666) .
  1. Remove upper intake manifold (9424) .
  1. Remove valve cover retaining bolts.
  1. Remove fuel injection supply manifold (9F792).
  1. Remove lower intake manifold as outlined.
  1. Remove exhaust manifolds (9430) as outlined.
  1. Loosen rocker arm seat retaining bolts enough to allow rocker arm (6564) to be lifted off the push rod (6565) and rotate to one side.
  1. Remove push rods . Identify position of each push rod . Push rods should be installed in their original position during assembly.
  1. Remove cylinder head retaining bolts and discard.
  1. Remove cylinder heads .
  1. Remove and discard old head gaskets (6051) .
Installation
  1. NOTE: Lightly oil all bolts and stud bolt threads before installation except those specifying special sealant.
    Clean cylinder head, intake manifold , valve cover (6582) and head gasket surfaces. If cylinder head was removed for head gasket replacement, check flatness and sealing areas for scratches of cylinder head and cylinder block gasket surfaces. Refer to Section 03-00 for procedure.
  2. Position new head gaskets onto cylinder block (6010) using cylinder head to block dowels (6A008) for alignment.

    Head Gasket


    a11431c.gif

  3. Position cylinder heads onto cylinder block .
  4. ani_caut.gif CAUTION: Always use new cylinder head bolts to ensure a leak-tight assembly. Torque retention with used bolts can vary, which may result in coolant or compression leakage at the cylinder head mating surface area.
    -ft).
  5. For 3.8L non-SC engine, tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
    1. 20 Nm (15 Lb-Ft)
    1. 40 Nm (29 Lb-Ft)
    1. 50 Nm (37 Lb-Ft)
  6. ani_caut.gif CAUTION: Do not loosen all of the bolts at the same time, only work on one bolt at a time or possible damage to engine or leakage may occur.
    In sequence, loosen retaining bolts two to three revolutions and retighten bolts one at a time in the following manner:
    1. Long bolts:
      • 15-25 Nm (11-18 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.
    1. Short bolts:
      • 10-20 Nm (7-15 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.


      a11399c.gif


      Item Part Number Description 1 6010 Cylinder Block 2 - Locating Pin (2 Req'd) 3 N802515-S Cylinder Head Bolt (4 Req'd Each Side) 4 6049 Cylinder Head 5 N802516-S Cylinder Head Bolt (4 Req'd Each Side) 6 6A008 Cylinder Head to Block Dowel
  7. NOTE: If original valve train components are being installed, a valve clearance check is not required. If a component has been replaced, perform a valve clearance check as outlined.
    Dip each push rod end in Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A and install push rods in their original position.
  8. For each valve, rotate crankshaft (6303) until valve tappet (6500) rests on the heel (base circle) of the camshaft lobe, before tightening rocker arm seat retaining bolts to 7-15 Nm (5-11 lb-ft) maximum.
  9. Lubricate all rocker arms with Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A. Final-tighten the rocker arm seat bolts to 30-40 Nm (22-30 lb-ft). For final tightening, camshaft (6250) may be in any position.
  10. Install exhaust manifolds as outlined.
  11. Install lower intake manifold as outlined.
  12. Install fuel injection supply manifold .
  13. Position valve cover and new valve cover gasket (6584) on cylinder head and install retaining bolts. Note location of ignition wire routing clip stud bolts. Tighten retaining bolts to 9-12 Nm (7-9 lb-ft).
  14. Install upper intake manifold .Install spark plugs (12405) , if removed.
  15. Connect ignition wires to the spark plugs .
  16. If LH cylinder head is being installed, perform the following:
    1. Install oil filler cap.
    1. Install generator/power steering pump mounting bracket.
    1. Install generator .
    1. Install main accessory drive belt tensioner .
    1. Install power steering pump (3A674) .
    1. Install power steering pump support bracket.If RH cylinder head is being installed, perform the following:
    1. Install positive crankcase ventilation valve .
    1. If equipped with A/C, install A/C compressor mounting brackets (2882) and A/C compressor .
  17. Install drive belt and tighten to specification.
  18. Connect battery ground cable .
  19. Install air cleaner outlet tube.
2010&c18=modelyear&c35=wsm%2ccylinder%20heads%2cssd%2c03-01a%2cin-vehicle%20service&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Posted on Mar 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Start


could be a motor mount or its not running on all cyclinders

Aug 23, 2014 | 1999 Mercury Cougar

1 Answer

Changed the spark plugs, battery, and fuses on my 2002 mercury cougar and it still wont start it just shoots out smoke from the exhaust.


if it is black smoke ,a number of things could cause this problem,map/mass air flow sensor,or timming,,if it is white smoke and head gasket or crack in the head would cause it to burn antifreeze.

Oct 04, 2013 | 2002 Mercury Cougar

4 Answers

99 pontiac montana overheaten already changed thermostat what is it?


you have a GM common problem and that is a bad intake manifold gasket. GM change the gaskets to plastic and they crank and leak causing over heating. here is a picture of one i took from a 2005 pon. bonneville with 74,000 miles on it2_12_2013_3_00_09_am.jpg

Feb 12, 2013 | 1999 Pontiac Montana

1 Answer

How hard is it to change the head gaskets on a 99 malibu


if your able to do so, it is not bad. if you go to any auto parts store and get a haynes manual for your car, it will tell how to do the job. they are based on a complete teardown of your vehicle. for less than 25.00.

May 19, 2010 | 2000 Chevrolet Malibu

2 Answers

My cougar overheats when my ac is on. what can be the problem


Thermostat stuck closed.

Clogged radiator.

Bad radiator cap.

Or blown head gasket.

Mar 29, 2010 | 1999 Mercury Cougar

1 Answer

Afteri change intake gastek do i need to hange head gastiks on a 99 chevy blazer


No you don't need to change the head gaskets, unless you suspect that you have a blown or leaking head gasket.

Feb 20, 2010 | 1999 Chevrolet Blazer

1 Answer

Canyou chage head gaskets on 99 ford cougar 2.5 v6 with engine in car


Yes! No need for the engine to come out at all. But there is going to be alot of parts coming out, you will need a manual from aoutozone or advance $14.99 It will tell you step by step.

Jun 21, 2009 | 2000 Mercury Cougar

1 Answer

Changing valve cover gasket


v6 or 4 cylinder?

SECTION 303-01A: Engine - 2.0L 1999 Cougar Workshop Manual
IN-VEHICLE REPAIR Valve Cover Removal
  1. Disconnect the oil feed sensor electrical connector.
  1. Disconnect the crankcase ventilation tube.
  1. Remove the appearance cover.
    1. Position the throttle cable out of the way, and the speed control cable (if equipped).
    1. Remove the eight bolts.
    1. Remove the appearance cover.
  1. Remove the spark plug wires.
  1. Detach the upper part of the engine front cover out of the way.
    1. Remove the four bolts.
    1. Position the front cover to one side.
  1. Remove the valve cover.
    1. Position the throttle cable to one side, and the speed control cable (if equipped).
    1. Remove the nine bolts.
    1. Remove the valve cover
---------------------------------------------------------------------------------------------

Mar 23, 2009 | 1999 Mercury Cougar

1 Answer

My '99 Cougar heated up the other day and when i parked and popped the hood some gray smoke came out. Now the car over heats a lot and the heater will only blow cold air out


Possible blown head gasket...sounds like it, remove the spark plugs and do a compression test, sometimes you will find water coming out of the spark plug hole with a blown head gasket, pull the plugs and turn the engine over, with the radiator full of water, if water starts spitting out of any of the spark plug holes...it's a cracked head, or blown head gasket.

Feb 24, 2009 | 1994 Buick Regal Gran Sport

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...