Question about 1999 Chevrolet K1500

1 Answer

I am trying to find out where the daytime running light curcuit board goes on a 1996 chevrolet silverodo

Have high beams but no low beams or running lights was told it was the circuit board

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 75,108 Answers

No that is not correct in my opinion.

Posted on Dec 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1997 Chevrolet Headlight problem

We had the same exact symptoms right down to the clicking noise under the dash. A friend who is a mechanic provided all the wiring diagrams, etc and when we pulled the dash we found that there was another enclosure behind the dash.....we stopped there.......

....waited a few days, did some research and decided since a replacement headlight switch was about $50.00 the easiest route was to to swap that out hoping it would fix the problem....was also a very easy installation.

Turns out that fixed the problem. Good luck!!!

Posted on Aug 13, 2008

  • 69 Answers

SOURCE: Daytime Running Lights

could be a fuse

Posted on Oct 06, 2008

SOURCE: !997 Chevrolet S10 headlight problem

I have had the same problem with my 97 S10. I looked at the GM iring diagram and found that the headlight circuit runs directly through the main headlight switch with no fuse or relay at all. The high low beam switch cannot shut the circuit off completely and therefore make the clicking relay sound that is heard. The daytime running light module looks for a headlight on signal and therefore shuts off the running lights. So when the headlights cut on and off the clicking you hear is the day time running light relay, turning them on thinking you are shutting the headlight switch on and off. Inside the headlight switch itself is a thermal metallic circuit protector similar to whats inside a flasher switch. This is the only logical place for the headlight circuit to cut out since it is a directly wired circuit as explained before. Replace your headlight switch for less than 20 bucks from autozone.

Posted on Oct 27, 2008

  • 2 Answers

SOURCE: 04 chev optra i have

I have a similar problem with my 2005 Optra 5 - daytime running lights are hit/miss. About 3-4 years ago, the alarm started activating itself - FREQUENTLY. Turns out it was corroded wires. Now this. (Take heart - my Corolla had a similar problem - bad sockets - bulbs burned out faster than they could be replaced. Toyota never did admit responsibility.)

Road Safety Recalls Database
Print this Page
Transport Canada Recall # 2007315 Recall Date: 2007/09/28 Notification Type: Safety Mfr System: Lights And Instruments Manufacturer Recall Number: 07240 Units Affected: question.gif 33,865 Category: Car Recall Details: Certain vehicles may experience a loss of headlamp low beam or Daytime Running Light (DRL) function as a result of a melted instrument panel harness connector. Low beam failure would lead to reduced visibility during hours of darkness. DRL failure may render the vehicle less visible to other motorists and pedestrians during daylight hours. Both cases could lead to a vehicle crash with injury or death. Correction: Dealers will add a direct connection splice clip to the headlamp low beam circuit in order to bypass the faulty connector. Make Model Model Year(s) Affected CHEVROLET OPTRA 2004 2005 2006

Posted on Oct 14, 2009

  • 429 Answers

SOURCE: i have a 2003 chevy cavalier. headlight issue

The blinking light is telling you that you have a headlight out, if you look the service light should be coming on when the light stops blinking.
Replace the head light and all should be fine.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

All of my running lights and blinkers work and high beams but no low beams on my 1997 Chevrolet TahoeA


Headlamps Inoperative - Low Beams

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the high beam headlamps are operating properly and the low beams are inoperative.

1

Did you perform the Headlights System Check?
--
Go to Step 2
Go to Headlight System Check

2

  1. Turn the headlamp and panel dimmer switch to the ON position.
  2. Move the headlamp dimmer switch to the LOW position.
  3. Backprobe the headlamp dimmer switch connector with a J 35616-200 from cavity A to ground.

Does the test lamp light?
--
Go to Step 3
Go to Step 5

3

  1. Remove the daytime running lamp relay.
  2. Connect a J 35616-200 at cavity G5 to ground.

Does the test lamp light?
--
Go to Step 4
Go to Step 6

4

  1. Re-install the daytime running lamp relay.
  2. Backprobe cavity B at the high/low beam headlamp with the headlamp dimmer switch in the LOW position.

Does the test lamp light?
--
Go to Step 7
Go to Step 8

5

Replace the headlamp dimmer switch.

Is the repair complete?
--
Go to Headlight System Check
--

6

Repair the open in CKT 359 (PPL) between the headlamp dimmer switch and the daytime running lamp relay.

Is the repair complete?
--
Go to Headlight System Check
--

7

Replace the high/low beam headlamps.

Is the repair complete?
--
Go to Headlight System Check
--

8

  1. Inspect for an open in CKT 12 (TAN) between the daytime running lamp relay and S120, repair as necessary.
  2. Replace the daytime running lamp relay if no open was found in CKT 12 (TAN) between the daytime running lamp relay and S120.

Is the repair complete?
--
Go to Headlight System Check
--

Jul 24, 2015 | Chevrolet Cars & Trucks

1 Answer

My high beam light is flashing on and off in day but when I turn the lights on it goes off. Also, I now have now day time running lights.


Daytime running Light module is overheating / it reduces power to low beam to create daytime running light . Ask yourself do I need this - If no law against it = UNPLUG control module . Your low beams will operate normal by turning on switch - Lever / Turn switch will turn on Highbeams but this switch can be Lose internally and Only cure is replace Signal Light Steering wheel switch . Common issue for all Cars is switch stalk / Lever is worn out by Aggressive use. If your car has Automatic light control - re they turn off after 30 second delay when you exit car - Try putting switch in manual mode means you Turn on - off by switch . But I really feel signal stalk is worn . DRCM is a known issue that can be unplugged . Final cheap solution unplug both high beams an Drive on low beam . $$$$$$$ spent chasing small problem will destroy $$$ needed for Bigger issues .

Jun 30, 2014 | 1996 Pontiac Grand Am

1 Answer

Low beams not working but high beams are on a 2000 chevy metro


The headlight relay provides power to the dimmer relay, then power goes thru a fuse for each light for each circuit (4). The low beam fuses are in fuse block 2. The dimmer relay is controlled by the daytime running light module. The headlight and dimmer switches send signals to the DRL module. You may need a shop manual to troubleshoot the circuits.

Jan 24, 2014 | 2000 Chevrolet Metro

1 Answer

1996 chevy suburban high beams work, low beams and daytime running lights don't. checked all fuses none blown, dont know how to check relays except to replace each one, one at at a time.


with a test light back probe the green wire behind the low beam then if test light on = bulb defect
the blue one is for daytime running lights example : if 1 bulb is burn or open no daytime running lights
p.s. you need to have 2 bulbs the same or it won't work

Aug 05, 2013 | 1996 GMC Suburban

2 Answers

HIGH BEAM LIGHT STAYS ON IN DASH ...SWITCH GOES HIGH AND LOW BUT ONLY WORKS ON HIGH (ONE LIGHT) AND NO LIGHTS ON LOW


I have the same problem and I've tried two fixes so far and neither has worked.
- I replaced the daytime running light module and that didn't work
- I replaced the trun signal/hazard/light switch and that didn's work

I've had one comment that it could be a ground issue.
hope this saves you spending money on "fixes" that don't solve the problem

Dec 03, 2010 | 1996 Pontiac Sunfire

2 Answers

No low beam lights or daytime lights - high beams work


both low beam ights wont work on my VW 2000 beetle I have checked the fuses, bulbs, and relays what could be the problem

Feb 04, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Low beam headlight /daytime light are not working


It's on the driver's side. Remove all the plastic & it's in there.Big rectangle, black box,about 1.5" thick,lotta wires.

Jun 22, 2009 | 1996 Chevrolet Tahoe

1 Answer

Green light is on not sure wat it means


DRL indicator light. (Daytime Running Lights)

Jan 23, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet K1500 Logo

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...