Question about Cars & Trucks

1 Answer

How to remove dash from 1976 tradesman 100 Dodge van?

Removed a couple of screws from each end ,wont budge.

Posted by on

  • Dan Lobner Dec 11, 2012

    thanks anyway.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,197 Answers

You need a manual, there a hidden screws all over the place. You can buy a used factory manual here.

Posted on Dec 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mikey108
  • 475 Answers

SOURCE: Replace Driver's side mirror - Jeep Liberty 2002

The door panel has plastic clips that hold it in place also. Put a thin blade screwdriver between the panel and door. Pry the panel away from the door. The panel will make a loud snapping noise, that is the clip coming out of the retaining hole. Sometimes the clips break.

Posted on Dec 09, 2008

  • 10 Answers

SOURCE: Removing Stereo from Nissan Terrano II

I THINK YOU WILL FIND THER IS 4 SCREWS HOLDING IT IN THERE IS ON MINE * *
* *

Posted on Apr 17, 2009

  • 48 Answers

SOURCE: Removing the 100 amp fuse link in a 1994 toyota corolla

the fuse link is bolted in from the two side in the fusebox.you have to un bolt the whole fusebox so you can raise it and if you look at the sides there are two side panels that can be moved down so you can get a socket or spanner on the two bolts apprx 10mm. undo them and raise the fuse out and put the new one in and tighten up the bolts again. hope this helps.

Posted on Apr 25, 2009

  • 356 Answers

SOURCE: facia panel removal to change radio

YOUTUBE HAS GOOD VIDEO ON FORD CAR
RADIO REMOVAL.

Posted on Apr 04, 2010

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 dodge ram van wont start


try the ignition coil connector and the ground on the coil which is through the screws holding the coil on, i removed and reinstalled the screws with lock washers to help the ground issue

Dec 30, 2012 | Cars & Trucks

1 Answer

Why have i lost all electrical power to my 1974 dodge tradesman van


With the battery connected, did you check the fuseable link which is the pigtail wire on the positive cable ?
If nothing works, it has to be a bad cable, bad connection, or one of the major fuseable links from the battery to the fuse box.

Aug 04, 2012 | Dodge Cars & Trucks

2 Answers

How to install a heater core on a 2005 dodge grand caravan


Very easy if you go through the lower part near the peddles

Dec 24, 2009 | 2005 Dodge Caravan

1 Answer

Fan switch broken, does dash need to come off, 90' dodge dakota


The bezel surround for the gauges and dash center (radio area) need to be removed to gain access to remove the switch. Should be about 10 torx screws and then pull straight out.

Should pull out easily when all screws are removed.

Nov 25, 2009 | 1990 Dodge Dakota

1 Answer

Replacing ignition switch on 1976 Dodge D-300. Got the steering wheel off and taken out the circlip holding in the bearing. I''ve loosened the three screws that hold the turn signal housing, but can''t...


Here is what MOTOR says to do. If you have Tilt and/or Telescopic steering wheel the column needs to come off the dash and the mounting bracket removed so the cover on the wire harness can be removed. It is mounted with screws. On the others the wire cover is held on with clips and need to come off. The shift lever has to be full clockwise on all models except Tilt. On Tilt wheels position the gear shift at the midway point. Unplug the wire harness and remove the screw for the turn signal lever and then the lever. If you have cruise, let it hang. Remove the hazard warning switch and upper bearing retainer mounting screws. Pull the switch from the column carefully, guiding the wires through the column opening. Installation is the reverse.Hope this helps.

Oct 25, 2009 | Chrysler 300 Cars & Trucks

1 Answer

How to remove the radio?


Remove screws from dash trim. Remove dash trim. Next remove screws from radio. Pull out radio then disconnect wires.

Jul 10, 2009 | 1994 Dodge Grand Caravan

1 Answer

Can't remove dash from 1990 toyota celica to replace dash bulbs


hi i had d same problem with my gt4,i lightly wedged a piece of hard plastic between any gap n popped open the clips,be careful tho

Jun 24, 2009 | 1990 Toyota Celica

1 Answer

Removing the door panel on a 2001 dodge intrepid


remove all screws ,pull panel off from botom ,careful not to break clips

Mar 28, 2009 | 2001 Dodge Intrepid

1 Answer

2001 dodge 1500 van, headlights stay on always.


It the multi-function lever (turn signal) . When you pull back the handle ,this turns on the high beams headlights and indicator on the dash.

Nov 14, 2008 | 2000 Dodge Ram Maxi

1 Answer

Radio installation in 1983 dodge ram van


remove screws from dash face, remove dash face. two 10mm bolts hold stereo in place,remove bolts, gently pull stereo out. unplug stereo. install new stereo by reversing the directions

Oct 19, 2008 | 1983 Dodge Ram Wagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...