Question about Cars & Trucks

1 Answer

No dash lights after installing an after market stereo in 2000 jimmy

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

Did you cut any wires

Posted on Dec 07, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: So when installing an after market radio in a 2000

rest assured you wont have to change the deck every year to pass a emissions test.

Posted on Apr 28, 2009

  • 3 Answers

SOURCE: dash lights, dome lights and stereo quit workign when installing

YOU HOOKED THE GROUND FOR THE RADIO TO THE WIRE FOR RADIO LIGHT FROM THE FACTORY UNIT. THAT WIRE IS DRAK BROWN AND WILL SHOW AS A GROUND UNTIL YOU TURN ON THE LIGHTS. YOUR FUSE FOR PARKING LIGHTS WILL ALSO BE BLOWN. I DID THIS AND FIXED IT ALSO.

Posted on Nov 26, 2009

  • 4 Answers

SOURCE: How do you get the dash apart and remove the

the screws for the dash are behind the heater vents,the heater vents pop out, one side of it will pop out with alittle pressure, a small flathead should do,theres four,two in the middle ,and one vent on either side.(took me two days of pulling hair and profanity to figure this out)

Posted on Feb 10, 2011

  • 4977 Answers

SOURCE: I am attempting to install an after market stereo

you can go to radio shack or other store and buy a plug adapter for your brand of radio that will match both the radio and the cars wiring so all you have to do is disconnect the factory radio and plug in the adapter to the radio and the original car wiring plug and your set to go without figuring out which wires to connect to and removing the possibility of causing wiring problems with the car

Posted on Mar 02, 2011

edwardjwoods
  • 372 Answers

SOURCE: 2002 Mitsubishi Gallant - installed

pull the radio back out and remove the wire marked dimmer control on the aftermarket radio then replace fuse

Posted on Apr 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dash lights only work when pressing brake


Undo what you have done as you have wired into the CPU system and it is sending the program haywire.. Seek help from professional radio installers as it is not a matter of just wiring in any where

Feb 22, 2014 | 2001 Dodge Ram Pickup 1500

1 Answer

Tail lights dash lights and turn signals not working


obviously it may have to do with the installation of the new stereo, while installing some fuse may have blown or wires are cut or wires were not put back in order.

Feb 08, 2013 | Cars & Trucks

1 Answer

2006 monte carlo tail lights and turn signals not working


you could have blown some fuse while installing the stereo. check the fuses, wires that may have been cut or disconnected.

Feb 08, 2013 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

2000 jimmy no dash lights after installing after market stereo


Check your fuses you have blown the dash light fuse. If you don't have the owners manual you can download it for free here.

Dec 07, 2012 | 2000 Chevrolet S-10

1 Answer

2002 Mitsubishi Gallant - installed after market stereo with wire nuts. Stereo works great, but the dash lights are out. Any Help?


pull the radio back out and remove the wire marked dimmer control on the aftermarket radio then replace fuse

Apr 24, 2011 | 2002 Mitsubishi Galant

1 Answer

I have a 2000 grand cherokee v8 and ive got battery problems


something is draning the battery.
it has to be the dash lights the dome lights or something being left in the cig lighters

or the lights arnt turning off after you close the door.
or an after market stereo was installed wrong and or the aftermarket amp.

keep me posted

jm

Jan 27, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Remove d/s airbag


disconnect the battery, then find the air bag plug normally under the seat or around side of the seat, maybe under the carpet *bright orange cable*

once you have disconnected the battery and the cable start taking the steering wheel apart and remove it, after market steering wheel will be needed unless your just going to cut the air back out and re fit the wheel, do not connect the air bag cable, you will have a dash light on the dash for air bag doing this though.

Apr 10, 2009 | 2000 GMC Jimmy

1 Answer

New radio installed - now dash lights don't work


Most factory stereos are wired to the dash dimmer switch. Usually if the dash lights go out after an after market stereo installation, it is because the wire that originally went to the factory stereo is not used for after market stereos. Double check the fuses and ensure the wire that controlled the lights on the factory stereo is not grounding out on something.

Nov 11, 2008 | 1998 Honda Passport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...