Question about 2007 Mazda MAZDA6

Open Question

How to replace headlight bulb on a mazda 6 - 2007 Mazda MAZDA6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How do you replace the head light bulb on a 2004 Mazda 6?

This is a problem - I had both drivers and passenger bulbs go on me and came at it through the wheel arch. The method is the same for both sides.

Equipment needed

Short handled Phillips screwdriver
2 x Latex gloves - to save scratches and dirty hands
Torch

Use 1 glove to save your hands
Lift bonnet to get as much light on the job as you can
Turn wheel in so you can get at wheel arch liner unmolested
Remove the plastic nuts – don’t loose them
Peel back liner – you can now see the back of the lens cover
You may need a torch, I did
Turn cover and pull it away – you can now see back of bulb
Remove clip, noting the way to the comes out, there is a notch on the base of the bulb and the replacement must go in that way

Use clean glove to handle bulb, keep to base of bulb and not the glass

Replace is the reverse of the above

Allow 30-45 mins first time

Posted on Nov 17, 2008

Ad
  • 1 Answer

SOURCE: how do I replace the headlight bulbs in my 2002 Mazda 626

On my Mazda I did the following:
- Pulled off the electrical connector socket from the back of the headlight housing.
- Pried off the rubber boot on the back side of the headlamp assembly.
- Removed the wire bracket surrounding bulb by removing the screw that held it in place, although it may be possible to remove the bulb without removing the bracket.
- Extract the bulb from the headlight assembly.

Reassembly was just the revrese of the above steps.

Posted on Feb 08, 2009

  • 1 Answer

SOURCE: Changing the bulb for a headlight

I guess you refer to the dipped beam headlamp?
If the light is a normal one, not the fancy expensive bright lamp, bluish colour light emitted you should be able to reach it throgh the wheelarch after removing part of the plastic trim.
The cover rotates and can be easily removed.
The there is the usual wire spring loop that hold the lamp in.
The lamp in mine was a standard H1 single filament bulb.
Took about 20 minutes to replace in semi darkness with the aid of a wind-up torch!

Hope this helps.

Paul H.

Posted on May 07, 2009

  • 1986 Answers

SOURCE: 05 Mazda 6 I need to replace the headlights

Behind the head lamp you'll see a circular cap with some fins on it. Turn it counter clockwise and then it should come out exposing the back of the bulb. Then you will need to push in and up on an angle to release the metal spring clip that holds the bulb in place. Then you can disconnect the harness to the back of the bulb and then remove the bulb. Do not touch the glass of the bulb when putting in the new one as that will cause the bulb to catastrophically fail

Posted on Oct 28, 2009

  • 1 Answer

SOURCE: how do i change mazda 6 headlight bulb

This is difficult give yourself a good 30 mins. I have only found one way. Bonnet up - You will need a slim torch and a stubby x headed strewdriver to remove the plastic screws that hold on the wheel arch cover. Turn wheel away to give you more room. Once this is out of the way you can see the back of the light cluster, A twist and the back cover comes off. Remove the electrical connector, locate the retaining clip (much of this is by feel) when you take out the bulb make sure you note the way it came out as the replacement must go in the same way. Do not touch the bulb glass with your fingers, use paper or gloves. By feel, re-fasten the clip then reconnect the electrics. Reposition cover and twist back on, Refasten wheel arch cover. Make sure the cover goes inside the lip of the wheel arch otherwise spray from the wheel may get in., good luck

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 Mazda 5 minivan how do I change the headlight bulb


Headlight Change 2006-2010 Mazda 5 - CarCareKiosk

www.carcarekiosk.com/video/2009_Mazda_5_Sport_2.../headlight
This free video shows how to change a burnt out headlight on a 2009 Mazda 5 Sport 2.3L 4 Cyl.. Complete instructions for replacing a head light bulb on a 2009 ...

Low beam head light bulb replace 2000-2006 Mazda Mpv ...

? 5:11
https://www.youtube.com/watch?v=kblzMLRJrok
Jun 29, 2013 - Uploaded by hp11208
Low beam head light bulb replace 2000-2006 Mazda Mpv .... My step dad and I successfully replaced a headlight yesterday! :-) ...I've lost it trying to replace the bulb. if anyone can let me know I would really appriciate it thanks ! ..... 5:00. Cleaning your IAC to fix rough idle on 2000 or 2001 Mazda MPV ...

Nov 29, 2015 | Mazda Cars & Trucks

1 Answer

Hi how can i replace my Mazda ^ 2006 headlight bulb ?


You can open the hood and you should be able to see the headlight compartment, right between your radiator on the front. Most Mazda's have a plastic cover on them. Simply turn the cover or pull it out. The light bulb is inside that compartment. Hope that helps you.

Jan 10, 2011 | 2004 Mazda 6

1 Answer

How do I replace a headlight light bulb?


Open the hood & reach to the rear of the headlight, turn the retainig ring to release the bulb, pull it away from the headlight & unplug it. Dont touch the replacement bulb with your fingers.

Jan 10, 2011 | 2005 Mazda 6

1 Answer

My mazda 6 ts2 seems to have 2 headlight bulbs that dont do anything any ideas


Steve, have you heard of spare bulbs. So that you do not lose/misplace them after cleaning the car, Mazda has placed them where they are required. Right in the headlights.

Dec 23, 2009 | 2006 Mazda 6

1 Answer

05 Mazda 6 I need to replace the headlights


Behind the head lamp you'll see a circular cap with some fins on it. Turn it counter clockwise and then it should come out exposing the back of the bulb. Then you will need to push in and up on an angle to release the metal spring clip that holds the bulb in place. Then you can disconnect the harness to the back of the bulb and then remove the bulb. Do not touch the glass of the bulb when putting in the new one as that will cause the bulb to catastrophically fail

Oct 28, 2009 | 2005 Mazda 6

2 Answers

Need to change headlight on 2003 mazda rx 6


If it is the headlight itself. There may be a cover or shroud on the front of the engin bay. Remove that, may be a combination of clips and screws. If it does not cever the light area, it is even easier. There will probably be 3 screws or nuts, remover these and unplug the electrical to the light. From there you should just be able to pop the light out of place. If you are just replacing the bulbs. Where the power goes into the assembly, turn the clip, may be grey in color and pull out of the headlight assembly and replace the light bulb. But don't touch the new bulb the oils from your skin will damage the bulb.

Apr 22, 2009 | 1994 Mazda MX-6

1 Answer

Change fog light bulbs in Mazda 6


Hi, I have a 2003 Mazda 6 which also has the fog light in the headlight assembly. I'm not sure but I would imagine the design is similar to yours. I had the left side blown and it took me roughly 10 minutes to get the bulb out. The cover on the back of the assembly has a push tab in the centre at the top and two locating tabs on the bottom. I had to push down fairly hard on the air filter side of the top tab while at the same time carefully levering the cover off with a flat blade screwdriver. There isn't a lot of room between the headlight and the air filter box but just enough that you can tilt the back cover over a bit and lift it straight up, out from the bottom locating tabs. Pull this cover right out and then you can see inside the back of the headlight assembly. The bulb has a wire retainer clip that you can push in with your fingers to unhook it and hinge it over. You may have to pull a wire terminal off to get at this clip better.You can now just pull the bulb out and remove the approx 5cm wire tail on the bulb out from it's terminal. Should be able to get a replacement bulb just about anywhere. Replacement would be the opposite only be careful not to touch the glass of the bulb with your fingers as this is detrimental to the life of the bulb. Don't forget to put the other wire terminal back on if you had to remove it. As far as the right side goes, I have never replaced the fog light but I have replaced the headlight bulbs which are also behind this cover so it should be possible. It was a while ago for that but if I remember rightly, I had to use a little mirror sometimes on the right headlight-bit of a pain. By the way, unlike me, before you ever replace a headlight bulb, check that the fuse isn't blown first. There is a fuse for low and high beam for both left and right headlights. I don't think that is the case with the fog lights. Hope this helps you or whoever else.
Cheers,Peter.

Feb 28, 2009 | 2006 Mazda 6

1 Answer

Mazda 6 2.3 sport 2002 headlights


If your car and headlights are off then you will not get a shock. You have to unplug the bulb to replace it anyway so there is no way for you to get shocked.

Dec 03, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2007 Mazda MAZDA6 Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...