Question about Cars & Trucks

1 Answer

What does a fuel pump relay for 1997 Crown vic look like?

Where is it located?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,197 Answers

It is listed in the owners manual, it is under the hood location is clearly shown in the OM if you don't have the OM you can download one free from Ford here

Posted on Dec 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 225 Answers

SOURCE: Fuel pump relay location 1997 celica

The relay and fuse is located under the hood in the relay box. It will be labeled on the lid. If fuse is good, then test the relay. Pull it out and with a test light see if there is power. If there is then remember that one. Have some one turn the key on and find another power wire. There should be 2 powers.If there is only one power then there maybe a problem in the ignition switch. If there is 2 powers then you need to get to the top of the fuel tank and see if power is getting to the pump. The power at the pump will be there for only a few seconds once the key is turned on and then will drop off. Let us know how it goes.

Posted on Aug 30, 2009

  • 752 Answers

SOURCE: where is the fuel pump relay located in a 1997 chevy blazer 4-dr.

In the glove box behind a plastic panel. There are 3 relays in there. The fuel pump is the one closest to the drivers side.

Posted on Mar 31, 2010

  • 1 Answer

SOURCE: Location of fuel pump relay on a 2001 Ford Crown Vic

where is the fuel pump relay on a 2001 crown vic p71

Posted on Apr 14, 2010

  • 5 Answers

SOURCE: 1988 Ford Crown Vic Horn Relay Location

The horn relay IS NOT located in a box toward the front of the engine. It is located just behind the radiator overflow reservoir and attached to the inner fender next to two other relays. It is the only one without a plastic cover over the top of it. FYI, our Crown Vic horn didn't blow, and the cruise didn't work. I changed the relay and still no horn. I decided to check the horns themselves. Found wires disconnected from terminals. Touched wire to horn terminal and horn blew incessantly. (previous owner had disconnected horn rather than diagnose why) Pulled the horn "button" from steering wheel and disconnected the wire leads and horn quit. Disassembled the "button" assembly. Foam had degraded over time between the contacts. (Ford has discontinued this part). Cleaned and replaced foam with Scotch foam mounting squares with holes punched out over contacts (2 layers thick). Re-assembled and viola! Horn and cruise control both work! Relay was bad as was horn button.

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'M NOT GETTING FUEL TO THE INJECTORS ON A 85 CROWN VIC . THE FUEL PUMP AND THE RELAY HAVE BENN REPLACED WHATS THE NEXT STEP/


You will only get fuel at the injectors when cranking, the pump wont run(Usually) with just the key on. This is to prevent the pump running in a crash and feeding the engine.

May 18, 2014 | 1985 Ford Crown Victoria

1 Answer

Fuel pump relay location


Yes In the trunk of some of the Crown Vics there is a switch next to the air ride control. It is called an Inertia switch and has a reset button. If you do not find this switch in the trunk, you will find it behind one of the kick panels above the front seat floorboard. It will sometimes activate by mistake with an impact.

The fuel pump relay should be in a Relay trio that is piggy-back to the Powerbox under the hood on the driver's side. There are plastic clips on one end which when pressed will allow the Relay trio to slide out of the case and towards the engine.

Oct 22, 2013 | Ford Crown Victoria Cars & Trucks

1 Answer

Fuel pump wire colors 97 crown vic


Power from the inertia switch should be pink black and ground is black.

Feb 24, 2013 | Cars & Trucks

1 Answer

Fuel pump not working


need a diagram for a 2001 crown vic police interceptor on droping a fuel tank so i can replace the fuel pump !!

Nov 13, 2012 | 1997 Ford Crown Victoria

1 Answer

LOCATION OF THE STARTER MOTOR RELAY AND THE LOCATION OF THE FUEL PUMP RELAY SWITCH ON A 1984 CROWN VIC. IT HAS'NT BEEN STARTED IN A FEW YEARS AND WE ARE TRYING TO TRACE THE PROBLEM


the starter relay is by the battery , follow the positive cable to it. that car should have a FUEL PUMP INERTIA switch. in the trunk, it should be well marked

Sep 01, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

1992 ford crown vic working fine, next day no power to fuel pump or cut off switch


  1. Hi Domino, The fuel shut off is powered by the fuel pump relay (which is in the engine compartment fuse block) the fuel pump relay is powered by the EEC power relay(PCM relay) you will have to check for distribution and voltage. I hope this helps!

Aug 31, 2010 | 1992 Ford Crown Victoria

1 Answer

2003 CROWN VIC HAS NO SPARK AND NO POWER TO FUEL PUMP CHECKED RELAYS AND FUSES CHANGED CRANK AND CAM SESOR LOOKED FOR BAD GROUND AND BROKEN WIRES AND HELP PLEASE


DID YOU CHECK THE FUEL PUMP SHUTOFF SAFETY SWITCH ON THE LH/DRIVERS SIDE IN THE TRUNK & MAKE SURE IT IS DOWN ,& EVEN IF IT IS SOMETIMES YOU CAN TAKE SOMETHING & PUSH IT UP & THEN PUSH IT BACK DOWN & IT WILL CRANK,& BELOW THAT SWITCH IN THE TRUNK IS A FUEL PUMP DRIVER MODULE ,IT MAY BE BAD,THOSE ARE A COUPLE OF THINGS THAT HAVE WORKED FOR ME ,& THATS PRETTY MUCH ALL I DO IS WORK ON FORDS, & LX CROWN VICS & P71 POLICE CROWN VICS WHERE I AM WORKING, HOPE THAT IT MIGHT HELP YOU FIX IT. SEAN

Nov 02, 2009 | 2003 Ford Crown Victoria

3 Answers

2001 crown vic keeps burning 30A PCM relay fuse


have fuel pump checked i have known a bad fuel pump shorting out causing pcm fuse to blow.

May 10, 2009 | 2001 Ford Crown Victoria

2 Answers

Location of fuel pump relay on a 2001 Ford Crown Vic


where is the fuel pump relay on a 2001 crown vic p71

Jan 10, 2009 | 2001 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...