Question about 2005 Peugeot 405

1 Answer

My peugeout 406 keeps overheating even after bleeding and ive changed the cylinder gasket, water pump and radiator. Havent seen any signs of leakage and the display shows " oil pressure insumfficient

The mileage is 200000km and i changed the oil and plugs too

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

This type of a car has a tendency of wapping the block.next tym you take out head have block checked that is if u have done all the above

Posted on Dec 28, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

billtec
  • 61 Answers

SOURCE: peugeot 106 overheated now building pressure in exspantion tank

HI,FIRST THING TO CHECK IS YOUR COOLING FAN COMING ON WHEN HOT? IF YES TRY REMOVEING T/STAT AND SEE IF IT OVERHEATS,TRY THIS BEFORE ANYTHING ,THANKS

Posted on Feb 20, 2009

  • 17 Answers

SOURCE: Peugeot 406 hdi executive 2002 will not start

hi pal was it doing it before you changed the battery or afterwards? try putting the key in the ignition and holding the lock button for 10-15 seconds it seems to be immobiliser fault and the key sign represents that its not coded to the car hop it helps you

Posted on Nov 15, 2009

Danniboi
  • 1098 Answers

SOURCE: peugeot 306 1.4 overheating problem, heater not

Hi its the head gasket, you cant see no water in the oil on these engines like you normally can on most oil caps, pull the dip stick out and look on the bottom any sign of yellow gundge will be the head gasket, sometimes it is only a very small amount.

These cars always have the same problem, if i was you I would do the head gasket and waterpump at the same time, water pumps are only about £20 and wont add much to the bill if doing them at the same time.

As there is no water coing out of the bleed niple then it must be air locked somewhere, problem is when they get like this the gasket will blow anyhow.

Hope this helps
Regards
Dan

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do I have to keep putting antifreeze into the reservoir car runs hot when it cools down all the antifreeze goes to the bottom of the reservoir


Andre, reading your comment,you said that you still topping up the radiator reservoir.By topping up the reservoir and often loose the coolant,means that if you do not have any water leakage from radiator, hoses,water pump or any core plugs, the fault might come either from the radiator cap, faulty thermostat,blogged radiator,faulty water pump ( probably the propeller inside are either not rotating with the pump shaft,or blades are missing even there is not any noise or coolant leak.) by having the above, the coolant pressurized and overflowed. The worst situation is having a problem with the cylinder head gasket. Also check whether no coolant does mixed with engine oil.If you do have this the fault is the cylinder head gasket. Visit the workshop.If you can not find anything from the above,my advise is to visit the workshop and ask them to do a leakage test for better results.Good Luck.

Mar 20, 2016 | Cars & Trucks

1 Answer

1993 Mercury Tracer overheating after running 15 miles or so


possibly air trapped on engine side of thermostat-possibly. HOW TO BLEED: loosen coolant temp sensor. Start engine. As engine warms, slightly unscrew sensor to allow air to escape. Once a steady stream of coolant trickles out you're good. Let us know if this helps. Good luck.

May 11, 2014 | Mercury Tracer Cars & Trucks

1 Answer

Its keeps overheating i change radiator and head gasket and still overheating


Did you also replace your thermostat? If it's stuck closed, engine will overheat.
When you did the HG, did you have head checked for cracks or warpage? A cracked head will cause severe overheating.A warped head may or may not show signs of external coolant leakage. Either of these conditions can occur if overheating is severe enough.
Are your hoses in good shape? An old hose can collapse when it's hot, and restrict flow. Feel them (when cool) for any sign of sponginess.
New radiator cap? The cap provides a seal to pressurize the cooling system.
Finally, how about your water pump? Any sign at the weep-hole of leaking coolant? Your water pump inner seal is bad, remedy is a new water pump. Or maybe the pumps' fins have corroded and not pushing coolant sufficiently. If there is corrosion, get the whole system flushed and start anew.
Pull your spark plugs and look for any sign of coolant in the cylinders. I know it's a pain to keep going back and checking, but you gotta be thorough. Plugs may be blistered white from overheating, but if you get it fixed, they should be alright.
Now, finally, really: sometimes, Randy, just a small air pocket in coolant can cause overheating. So, make sure you bleed the system if it has a bleed screw, or fill, cap loose, run engine till t-stat opens, level in radiator drops, then re-fill, and add coolant to your overflow reservoir to around the full hot mark. Tighten cap, and you are done. Good luck.

Oct 20, 2011 | 2004 Jeep Grand Cherokee

1 Answer

Car keeps overheating. we got new radiator cap from the dealer, still too hot. Then we changed water pump and flushed system, still too hot. Then we called cadillac and spoke with service who told us it...


i have seen several cases where headgasket leak could not be found by compression test check for engine heating up rather quick as 600 degree gas is entering cooing system also die is sold that can be added to cooling system that changes color if mixed with combustion (keep in mind dealers are chomping at the bit to get a couple thousand dollar headgasket job) one other test is a cooling system tester put on the radiator crank the engine if gauge rises with rotation of engine suspect head gasket if not change radiator

Feb 18, 2010 | 1997 Cadillac Seville

1 Answer

Losing antifreeze, but I see no leakage on the


If you are loosing radiator water/antifreeze and you see 'white' smoke out of your exhaust then it is likely that you are seeing steam: this usually indicates that you have a blown cylinder head gasket or have a cracked ylinder head: both situation will cause overheating of your engine. You can also check this situation by waiting until the engine is COLD, opening the radiator cap, refill with clean radiator fluid/water, restart the engine and see if the water as seen in the radiator is violently bubbling. Another condition before even starting the car again is if you see oil/white-brown staining in the radiator fluid caused by cracked cylinder head or gaskets letting engine oil in the radiator circuit. In any case, it is a critical sitation and you should get it checked and fixed immediately.
Hope it helps and please let me know if I have assessed the correct situation.

Jan 23, 2010 | 1995 Land Rover Range Rover

2 Answers

I have a 1990 gmc 1500 5 speed that is overheating and leaking coolant i changed the radiator hoses,thermostat, and water pump, and i know the leak is not coming from the radiator what do i do next?


any external leaks?coolant stains? would check the intake for signs of leakage also the heater hose quick connect.also check the sides of the block for leakage from the core plugs.

Jan 02, 2010 | 1990 GMC C1500

3 Answers

Hi, my 99 vw beetle was overheating and overheated really bad (smoking and really hot). towed to repair shop , he replaced radiator, head gasket (head gasket blown). now he says its still overheating and...


hi it mite be that the water pumps impeller is made of plastic on these models an they break up after time (very common on audis an vw same engines)and dont pump the water effectivley the car constantley over heat.the solution is to but a pump wid a metal impeller ive had the same problem on my audi a3 turbo..also changing the thermostat is an option...hope this helps












May 21, 2009 | Volkswagen Beetle Cars & Trucks

2 Answers

Overheating and rust on B-pillars


the overheating could be due to head gasket/cylinder head failure. you should examine the coolant reservoir for oil contaimination & have a look at the engine oil.

Apr 23, 2017 | 2004 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...