Question about 1996 Jeep Cherokee

1 Answer

Clutch not disengageing on 1996 jeep cherokee

How do i bleed the hyd for the cltch that has a slave cylindar? I dont see any bleeder screws by the slave cylindar.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

There has to be a bleeder there unless someone broke it off. If so, your best option is to replace it. In order to be malfunctioning, there has to be a reason. Air just does not enter the system by itself... Either the clutch master, slave cyl or a line between the two is bad, or the clutch itself is worn. Check everything carefully before deciding upon a repair plan.

Posted on Jan 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to install a new clutch in my 96 jeep cherokee it is a sealed unit I have it in but it wont go into gear how do I blead it or does it need to be blead???


I would start by topping off the clutch fluid.If you have replaced clutch the fluid level will drop.There is a bleeder screw at the slave cylinder.Basically you can pump the pedal and hold it down while someone opens the bleeder.Close the bleeder when pressure is released and then release pedal and repeat procedure.Good Luck!

May 10, 2011 | 1996 Jeep Cherokee Sport

1 Answer

I have a 1996 f150 4x4 5 speed v 4.9 engine that the clutch mastercylinder has to be pumped up before you can put vehicle in gear. It has a new clutch mastercylinder should I change out the slave cylinder?


did you bleed the slave cylinder? On the slave cylinder there should be a bleeder screw just like a brake caliper, perform the bleed procedure just like a brake, pump clutch and open slave bleeder, repeat untill all air is no longer noticed. keep master filled with fluid and top off when completed

Mar 09, 2011 | 1996 Ford F150 Regular Cab

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

I put a slave cylinder in a year ago, a new clutch in august, an three master cylinders since then an my clutch is still engaging then disengaging when the pedal is on the floor, what could the problem be?


I have always found the slave bleeding instructions inadequate. The way they design the slave with the bleeder away from the piston makes the standard bleeding ineffective. Unbolt the slave and put a wrench on the bleeder nut. Hold the slave in your left hand with your thumb over the pusher. Open the bleeder with your right hand and push the piston into the slave. Close the bleeder, release the piston, and repeat until air is out. This is essentially a bench bleed on the car.

jturcotte_351.gif

Nov 29, 2010 | 1996 Honda Accord

1 Answer

Looking for a diagram for a 1999 Jeep Wrangler Sahara that shows photos on how to find the bleeder screw on bleeding the clutch


You wont need a photo its super easy, but it is under the jeep follow the line from resivior to the clutch master cylinder (holds fluid) then the other end located on the trannsmission is the slave cylinder the bleeder is on it usually has a rubber cap on it! hope this helps. p.s. dont let the resivoir get empty it will leave air in the system and make bleeding almost impossible.

Aug 17, 2010 | 1999 Jeep Wrangler

2 Answers

How to bleed the clutch that has no bleeder screw or fittings what so ever? As it is hard to put in gear, cause its acting like the clutch is not being pressed in all the way?


If it has no bleed screw then you need to loosen the flange nut(that holds the pipe to the slave cylinder). Pump the pedal a couple times then hold it down. Loosen the nut till the fluid comes out. Fasten again. Pump and hold. Loosen etc.

Jul 25, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I have a 94 dodge 2500 v10 and i just replaced the clutch and all the hydraulic clutch system and my clutch wont disengage?


you need to bleed it just like brakes.fill the reservoir for clutch with brake fluid and open the bleed on slave cylinder and just let it drip dont touch the clutch pedal.keep eye on reservoir and add some when it goes down DONT RUN IT DRY! about 10 minutes of this should do. close bleeder screw and try it it should work. if not then recheck your installation

Mar 20, 2010 | 1994 Dodge Ram 2500

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

My 94 jeep wrangler 4.0 when stopped with car in gear with clutch pedal pressed to floor sometimes the clutch disengages and i have changed slave cylinder and clutch resevoir is full. my version has...


may have a bad mastercylinder for slave, also did you bleed system good and no leaks,id say master may be the problem or clutch preasure plate is bad .good luck.

Oct 27, 2009 | 1996 Jeep Cherokee

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...