Question about Cars & Trucks

Open Question

Removing speakers without the panel coming off

Can the speakers from a 1998 Lincoln town car be removed without the panel coming off.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1997 Town Car - How do you remove the complete dash board panel?

There are 3 small bolts across the top where the front defrost grill is. 2 large bolts directly under the headlight switch and another big bolt lower right hand corner of the glovebox area.

Posted on Feb 19, 2009

Ad
  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

kennyz195
  • 61 Answers

SOURCE: 2003 Lincoln Town Car - Power window switch removal/installation

SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.

  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Posted on Apr 05, 2010

c17hydro
  • 2984 Answers

SOURCE: need to remove the dash

Removal & Installation

  1. If equipped, turn the air suspension service switch to the OFF position before raising the vehicle.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Front seats
    • Carpeting
    • Rear airflow duct
    • Heater hoses
    1. Remove the driver’s side air bag module by removing or disconnect the following:
    2. SRS module-to-steering wheel bolts, from both sides of the steering wheel.
    • SRS module and disconnect the electrical connector
    • Horn switch electrical connector
    1. Remove the passenger’s side SRS module by removing or disconnecting the following:
    2. Open the glove box and disconnect the glove compartment isolator
    • Push inward on the 2 glove box door tabs and lower it
    • SRS module’s electrical connector
    • SRS module-to-instrument panel bolts and the module
    1. Remove the instrument panel by removing or disconnecting the following:
    2. Speed control servo nuts and move the servo aside
    • Bolt and disconnect the left side bulkhead connector
    • Left side bulkhead connector from the dash panel
    • Windshield washer fluid reservoir screw, and position the reservoir aside
    • Blower motor electrical connector
    • Air conditioning pressure cut-off switch electrical connector
    • In-line electrical harness connector
    • Electronic Automatic Temperature Control (EATC) variable blower motor controller electrical connector
    • Right front wheel
    • Right front fender splash shield bolts and move the shield away from the cowl
    • Wiring harness from the evaporator case
    • Wiring harness from the cowl
    • Right side instrument panel lower insulator pushpins, disconnect the power point electrical connector, remove the courtesy lamp from the socket and remove the insulator
    • Unseat the wiring grommet and feed the wiring harness through the cowl
    • Cowl side trim panels and the windshield side garnish moldings from both sides
    • Locking clip and the Electronic Crash Sensor (ECS) module electrical connector
    • Antenna connector
    • Ground wire bolts from the right side
    • EATC hose at the evaporator housing
    • Bolt and disconnect the bulkhead connector from the right side
    • Pull the door weatherstrip seals away from the instrument panel on both sides
    • Tunnel brace trim cover
    • Climate control head vacuum harness connector
    • Instrument panel tunnel brace nuts and the brace
    • Ground wire bolts from the left side
    • Wiring harness connectors from the left side
    • Parking brake switch electrical connector
    • Pry out the instrument panel defroster opening grille, disconnect the electrical connectors and the remove the grille.
    1. Remove or disconnect the following:
    2. 3 upper instrument panel screws
    • Instrument panel cowl side nut from both sides
    • Instrument panel cowl side bolt. From the left side
    • Instrument panel
    • Windshield wiper mounting arm and the pivot shaft
    • Electrical connector and remove the upper cowl extension screw and the extension
    • Vacuum hoses and the wire harness connector from the evaporative emissions canister purge valve
    • Evaporative emissions purge valve nuts and the valve
    • Cowl side nut
    • Right side rear fender apron screws and reposition the apron
    • Evaporator housing nut and screw
    • Vacuum hoses and the wiring harness connectors
    • Plenum chamber’s lower flange nuts
    • Plenum chamber’s upper flange nut and the plenum chamber
    • Heater core cover-to-heater plenum chamber screws and the cover
    • Seal and the heater core
  • Posted on May 26, 2010

    • 95 Answers

    SOURCE: fuse box diagram for 1998 lincoln

    should be a cover over the fuse box with a digram on it

    Posted on Jun 16, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How remove the cylinder head of motor from a lincoln navigator 1998 without moving the timing chain


    Impossible. This is a dual cam engine. There is a camshaft in each cylinder head. The head cannot be removed without removing the timing chain.

    Nov 03, 2015 | 1998 Lincoln Navigator

    1 Answer

    How to remove front middle arm rest 1998 lincoln town car?


    Easiest way is get a hacksaw and cut the rod its attached to on both sides.

    Only other way I can see doing involves removing the all seats.

    Oct 29, 2015 | 1998 Lincoln Town Car

    1 Answer

    Ecm 98 lincoln town car where is it located?


    under the steering column to the right. remove panels Plastic and steel panels to reach ecm

    Sep 29, 2014 | 1998 Lincoln Town Car

    1 Answer

    How I removar inside door penel of drive door fo changing windown motor of lincoln town car 1998/


    the panel is held in place with metal clips which will pry apart. use a putty knife and patiently work your way around the perimeter of the panel. it will come off.

    Sep 07, 2009 | 1998 Lincoln Town Car

    1 Answer

    I need to change the bulb in the analog clock in my 1999 Lincoln Towncar. How do I go about getting to it without tearing apart the dashboard?


    you need a special tool to get the radio out. It has pins that spread out spring clips so the radio can pull out.

    please rate as solved if this helps.

    SECTION 413-00: Instrument Cluster and Panel Lighting — General Information 1999 Town Car Workshop Manual
    REMOVAL AND INSTALLATION Bulb —Electric Clock
    Special Tool(s) Radio Removing Tool
    T87P-19061-A

    2242b54.gif
    Removal
    1. Disconnect the battery ground cable.
    1. Pull out the radio using Radio Removing Tool.
    1475891.gif
    1. Remove the radio.
      1. Disconnect the electrical connectors.
      1. Disconnect the antenna cable.
      1. Remove the radio.
    1. Remove the instrument cluster finish panel bolts.
    c7eab47.gif
    1. Remove the instrument cluster finish panel bolts.
    054ed10.gif
    1. Pull out and position aside the instrument cluster finish panel.
    cc71028.gif
    1. Disconnect the electric clock electrical connector.
    1. Remove the instrument cluster finish panel.
      1. Disconnect the headlight switch electrical connector.
      1. Disconnect the dimmer switch electrical connector.
      1. Remove the instrument cluster finish panel.
    1. Remove the electric clock illumination bulb.

    Apr 23, 2009 | 1999 Lincoln Town Car

    3 Answers

    Lincoln Town Car 1999 driver side window switch


    The plastic piece around the switches comes off and the entire cartridge comes out. It just snaps into the armrest. My 98 continental having similar issues. All other switches work, drivers window just quit. Tried a new cartridge did not fix problem.....still working on it.

    Apr 06, 2009 | 2000 Lincoln Town Car

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...